13 CB500F-32MGZA000.book 1 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when it is resold. This publication includes the latest production information available before printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. The vehicle pictured in this owner’s manual may not match your actual vehicle. © 2012 Honda Motor Co., Ltd. 13 CB500F-32MGZA000.book 2 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Welcome Congratulations on your purchase of a new Honda motorcycle. Your selection of a Honda makes you part of a worldwide family of satisfied customers who appreciate Honda’s reputation for building quality into every product. To ensure your safety and riding pleasure: ● Read this owner’s manual carefully. ● Follow all recommendations and procedures contained in this manual. ● Pay close attention to safety messages contained in this manual and on the motorcycle. The following codes in this manual indicate each country. ● The illustrations here in are based on the CB500FA ED type. Country Codes ● Code CB500F E, II E F, II F ED, III ED CB500FA E, II E F, II F ED, III ED U Country UK France, Belgium European direct sales UK France, Belgium European direct sales Australia, New Zealand *The specifications may vary with each locale. 13 CB500F-32MGZA000.book 3 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 A Few Words About Safety Your safety, and the safety of others, is very important. Operating this motorcycle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on safety labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining a motorcycle. You must use your own good judgement. You will find important safety information in a variety of forms, including: ● Safety labels on the motorcycle ● Safety Messages preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION. These signal words mean: 3 DANGER You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 WARNING You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 CAUTION You CAN be HURT if you don’t follow instructions. Other important information is provided under the following titles: NOTICE Information to help you avoid damage to your motorcycle, other property, or the environment. 13 CB500F-32MGZA000.book 4 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Contents Motorcycle Safety P. 2 Operation Guide P. 18 Maintenance P. 41 Troubleshooting P. 84 Information P. 104 Specifications P. 116 Index P. 119 13 CB500F-32MGZA000.book 2 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Motorcycle Safety This section contains important information for safe riding of your motorcycle. Please read this section carefully. Safety Guidelines .........................................P. 3 Image Labels.................................................P. 6 Safety Precautions .....................................P. 11 Riding Precautions .....................................P. 12 Accessories & Modifications......................P. 16 Loading .......................................................P. 17 13 CB500F-32MGZA000.book 3 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Safety Guidelines Safety Guidelines Always Wear a Helmet It’s a proven fact: helmets and protective apparel significantly reduce the number and severity of head and other injuries. So always wear an approved motorcycle helmet and protective apparel. 2 P. 11 Before Riding Take Time to Learn & Practice Even if you have ridden other motorcycles, practice riding in a safe area to become familiar with how this motorcycle works and handles, and to become accustomed to the motorcycle’s size and weight. Ride Defensively Always pay attention to other vehicles around you, and do not assume that other drivers see you. Be prepared to stop quickly or perform an evasive maneuver. Make sure that you are physically fit, mentally focused and free of alcohol and drugs. Check continued 3 Motorcycle Safety Follow these guidelines to enhance your safety: ● Perform all routine and regular inspections specified in this manual. ● Stop the engine and keep sparks and flame away before filling the fuel tank. ● Do not run the engine in enclosed or partly enclosed areas. Carbon monoxide in exhaust gases is toxic and can kill you. that you and your passenger are both wearing an approved motorcycle helmet and protective apparel. Instruct your passenger on holding onto the grab rails or your waist, leaning with you in turns, and keeping their feet on the footpegs, even when the motorcycle is stopped. 13 CB500F-32MGZA000.book 4 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Safety Guidelines Make Yourself Easy to See Motorcycle Safety Make yourself more visible, especially at night, by wearing bright reflective clothing, positioning yourself so other drivers can see you, signaling before turning or changing lanes, and using your horn when necessary. Ride within Your Limits Never ride beyond your personal abilities or faster than conditions warrant. Fatigue and inattention can impair your ability to use good judgement and ride safely. Don’t Drink and Ride Alcohol and riding don’t mix. Even one alcoholic drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. Don’t drink and ride, and don’t let your friends drink and ride either. 4 Keep Your Honda in Safe Condition It’s important to keep your motorcycle properly maintained and in safe riding condition. Inspect your motorcycle before every ride and perform all recommended maintenance. Never exceed load limits (2 P. 17), and do not modify your motorcycle or install accessories that would make your motorcycle unsafe (2 P. 16). If You are Involved in a Crash Personal safety is your first priority. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. Call for emergency assistance if needed. Also follow applicable laws and regulations if another person or vehicle is involved in the crash. If you decide to continue riding, first evaluate the condition of your motorcycle. If the engine is still running, turn it off. Inspect for fluid leaks, 13 CB500F-32MGZA000.book 5 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Safety Guidelines 3 WARNING Motorcycle Safety check the tightness of critical nuts and bolts, and check the handlebar, control levers, brakes, and wheels. Ride slowly and cautiously. Your motorcycle may have suffered damage that is not immediately apparent. Have your motorcycle thoroughly checked at a qualified service facility as soon as possible. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any areas or activities that expose you to carbon monoxide. Carbon Monoxide Hazard Exhaust contains poisonous carbon monoxide, a colourless, odorless gas. Breathing carbon monoxide can cause loss of consciousness and may lead to death. If you run the engine in confined or even partly enclosed area, the air you breathe could contain a dangerous amount of carbon monoxide. Never run your motorcycle inside a garage or other enclosure. 5 13 CB500F-32MGZA000.book 6 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Image Labels Image Labels Motorcycle Safety The following pages describe the label meanings. Some labels warn you of potential hazards that could cause serious injury. Others provide important safety information. Read this information carefully and don’t remove the labels. If a label comes off or becomes hard to read, contact your dealer for a replacement. There is a specific symbol on each label. The meanings of each symbol and label are as follows. 6 Read instructions contained in Owner’s Manual carefully. Read instructions contained in Shop Manual carefully. In the interest of safety, take the motorcycle to be serviced only by your dealer. DANGER (with RED background) You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. WARNING (with ORANGE background) You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. CAUTION (with YELLOW background) You CAN be HURT if you don’t follow instructions. 13 CB500F-32MGZA000.book 7 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Image Labels continued 7 Motorcycle Safety BATTERY LABEL DANGER • Keep flame and spark away from the battery. Battery produce explosive gas that can cause explosion. • Wear the eye protection and rubber gloves when handling the battery, or you can get burned or lose your eyesight by the battery electrolyte. • Do not allow children and other people to touch a battery unless they understand proper handling and hazards of the battery very well. • Handle the battery electrolyte with extreme care as it contains dilute sulfuric acid. Contact with your skin or eyes can burn you or cause loss of your eyesight. • Read this manual carefully and understand it before handling the battery. Neglect of the instructions can cause personal injury and damage to the motorcycle. • Do not use a battery with the electrolyte at or below the lower level mark. It can explode causing serious injury. 13 CB500F-32MGZA000.book 8 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Image Labels Motorcycle Safety RADIATOR CAP LABEL DANGER Except U type NEVER OPEN WHEN HOT. Hot coolant will scald you. Relief pressure valve begins to open at 1.1 kgf/cm2. ACCESSORIES AND LOADING WARNING LABEL WARNING Except U type ACCESSORIES AND LOADING • The safety stability and handling of this motorcycle may be affected by the addition of accessories and luggage. • Read carefully the instructions contained in user’s manual and installation guide before installing any accessory. • The total weight of accessories and luggage added to rider’s and passenger’s weight should not exceed 182 kg (401 lb), which is the maximum weight capacity. • The luggage weight must not exceed 11 kg (24 lb) under any circumstances. • The fitting of large fork-mounted or large handlebar mounted fairing is not recommended. 8 13 CB500F-32MGZA000.book 9 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Image Labels Motorcycle Safety TYRE INFORMATION LABEL Cold tyre pressure: [Driver only] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 290 kPa (2.90 kgf/cm2, 42 psi) [Driver and passenger] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 290 kPa (2.90 kgf/cm2, 42 psi) Tyre size: Front 120/70ZR17M/C (58W) Rear 160/60ZR17M/C (69W) Tyre brand: DUNLOP METZELER Front D222F ROADTEC Z8 INTERACT E Rear D222 ROADTEC Z8 INTERACT continued 9 13 CB500F-32MGZA000.book 10 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Image Labels Motorcycle Safety 10 SAFETY REMINDER LABEL For your protection, always wear helmet, protective apparel. FUEL LABEL Unleaded petrol only DRIVE CHAIN LABEL Keep chain adjusted and lubricated. 35 to 45 mm (1.4 to 1.8 in) Freeplay 13 CB500F-32MGZA000.book 11 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Safety Precautions Safety Precautions ● Face shield with unobstructed field of vision handlebar and feet on the footpegs. ● Keep passenger’s hands onto the grab rails or your waist, passenger’s feet on the footpegs while riding. ● Always consider the safety of your passenger, as well as other drivers and riders. Protective Apparel Make sure that you and any passenger are wearing an approved motorcycle helmet, eye protection, and high-visibility protective clothing. Ride defensively in response to weather and road conditions. ❙ Helmet Safety-standard certified, high-visibility, correct size for your head ● Must fit comfortably but securely, with the chin strap fastened 3 WARNING Not wearing a helmet increases the chance of serious injury or death in a crash. Motorcycle Safety or other approved eye protection ● Ride cautiously and keep your hands on the Make sure that you and any passenger always wear an approved helmet and protective apparel. ❙ Gloves Full-finger leather gloves with high abrasion resistance ❙ Boots or Riding Shoes Sturdy boots with non-slip soles and ankle protection ❙ Jacket and Trousers Protective, highly visible, long-sleeved jacket and durable trousers for riding (or a protective suit). 11 13 CB500F-32MGZA000.book 12 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Riding Precautions Riding Precautions Motorcycle Safety 12 Running-in Period During the first 500 km (300 miles) of running, follow these guidelines to ensure your motorcycle’s future reliability and performance. ● Avoid full-throttle starts and rapid acceleration. ● Avoid hard braking and rapid down-shifts. ● Ride conservatively. Brakes Observe the following guidelines: ● Avoid excessively hard braking and sudden shifting to a lower gear. u Sudden braking can reduce the motorcycle’s stability. u Where possible, reduce speed before turning; otherwise you risk sliding out. ● Exercise caution on low traction surfaces. u The tyres slip more easily on such surfaces and braking distances are longer. ● Avoid continuous braking. u Repeated braking, such as when descending long, steep slopes can seriously overheat the brakes, reducing their effectiveness. Use engine braking with intermittent use of the brakes to reduce speed. ● For full braking effectiveness, operate both the front and rear brakes together. 13 CB500F-32MGZA000.book 13 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Riding Precautions ❙ Anti-lock Brake System (ABS) This model is equipped with an Anti-lock Brake System (ABS) designed to help prevent the brakes from locking up during hard braking. ● ABS does not reduce braking distance. In certain circumstances, ABS may result in a longer stopping distance. ● ABS does not function at speeds below 10 km/h (6 mph). ● The brake lever and pedal may recoil slightly when applying the brakes. This is normal. ● Always use the recommended tyres to ensure correct ABS operation. ❙ Engine Braking Engine braking helps slow your motorcycle down when you release the throttle. For further slowing action, downshift to a lower gear. Use engine braking with intermittent use of the brakes to reduce speed when descending long, steep slopes. Motorcycle Safety CB500FA only ❙ Wet or Rainy Conditions Road surfaces are slippery when wet, and wet brakes further reduce braking efficiency. Exercise extra caution when braking in wet conditions. If the brakes get wet, apply the brakes while riding at low speed to help them dry. continued 13 13 CB500F-32MGZA000.book 14 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Riding Precautions Parking Motorcycle Safety ● Park on a firm, level paved surface. ● If you must park on a slight incline or loose surface, park so that the motorcycle cannot move or fall over. ● Make sure that high-temperature parts cannot come into contact with flammable materials. ● Do not touch the engine, muffler, brakes and other high-temperature parts until they cool down. ● To reduce the likelihood of theft, always lock the handlebar and remove the key when leaving the motorcycle unattended. Use of an anti-theft device is also recommended. ❙ Parking with the Side Stand 1. Stop the engine. 2. Push the side stand down. 14 3. Slowly lean the motorcycle to the left until its weight rests on the side stand. 4. Turn the handlebar fully to the left. u Turning the handlebar to the right reduces stability and may cause the motorcycle to fall. 5. Turn the ignition switch to the LOCK position and remove the key. 2 P. 35 13 CB500F-32MGZA000.book 15 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Riding Precautions Refuelling and Fuel Guidelines Motorcycle Safety Follow these guidelines to protect the engine and catalytic converter: ● Use only unleaded petrol. ● Use recommended octane number. Using lower octane petrol will result in decreased engine performance. ● Do not use fuels containing a high concentration of alcohol. 2 P. 108 ● Do not use stale or contaminated petrol or an oil/petrol mixture. ● Avoid getting dirt or water in the fuel tank. 15 13 CB500F-32MGZA000.book 16 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Accessories & Modifications Motorcycle Safety 16 Accessories & Modifications We strongly advise that you do not add any accessories that were not specifically designed for your motorcycle by Honda or make modifications to your motorcycle from its original design. Doing so can make it unsafe. Modifying your motorcycle may also void your warranty and make your motorcycle illegal to operate on public roads and highways. Before deciding to install accessories on your motorcycle be certain the modification is safe and legal. 3 WARNING Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding accessories and modifications. Do not pull a trailer with, or attach a sidecar to, your motorcycle. Your motorcycle was not designed for these attachments, and their use can seriously impair your motorcycle’s handling. 13 CB500F-32MGZA000.book 17 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Loading Loading motorcycle’s handling, braking and stability. Always ride at a safe speed for the load you are carrying. ● Avoid carrying an excessive load and keep within specified load limits. 2 Maximum weight capacity / Maximum luggage weight P. 116 ● Tie all luggage securely, evenly balanced and close to the centre of the motorcycle. ● Do not place objects near the lights or the muffler. Overloading or improper loading can cause a crash and you can be seriously hurt or killed. Follow all load limits and other loading guidelines in this manual. Motorcycle Safety ● Carrying extra weight affects your 3 WARNING 17 Operation Guide 13 CB500F-32MGZA000.book 18 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Parts Location Rear brake fluid reservoir (P70) Operation Guide Battery (P63) Fuse box (P102) Main fuse (P103) Engine oil fill cap (P64) Front brake fluid reservoir (P70) Front brake lever Throttle grip (P80) Engine oil filter (P66) Engine oil level inspection window (P64) Rear brake pedal 18 13 CB500F-32MGZA000.book 19 ページ Clutch lever (P77) ２０１２年１１月２７日 火曜日 午後３時５７分 Crankcase breather (P81) Side cover (P60) Front seat (P59) Rear seat (P58) Operation Guide Fuel fill cap (P38) Engine oil drain bolt (P66) Rear suspension spring preload adjuster (P82) Drive chain (P73) Coolant reserve tank (P68) Shift lever (P37) Side stand (P72) 19 13 CB500F-32MGZA000.book 20 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments Operation Guide SEL button SET button Display Check When the ignition switch is turned on, all the mode and digital segments will show, and the tachometer segment progresses to maximum scale and then disappear. If any part of these displays does not come on when it should, have your dealer check for problems. 20 13 CB500F-32MGZA000.book 21 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Speedometer NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. Tachometer red zone (excessive engine rpm range) Operation Guide Tachometer Clock (12-hour display) To set the clock: (P26) Fuel gauge Remaining fuel when only 1st (E) segment starts flashing: approximately 2.8 litres (0.74 US gal, 0.62 Imp gal) If the fuel gauge indicator flash sequentially or turned off: (P89) continued 21 13 CB500F-32MGZA000.book 22 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments (Continued) Operation Guide Odometer [TOTAL] & Tripmeter [A/B] & Fuel mileage meter & Fuel consumption meter SEL button selects the odometer, tripmeter A, tripmeter B, current fuel mileage, average fuel mileage and fuel consumption. u To reset the tripmeter: (P24) Odometer Tripmeter A Tripmeter B Reserve fuel consumption (P25) 22 Current fuel mileage Average fuel Fuel mileage consumption 13 CB500F-32MGZA000.book 23 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Operation Guide The average fuel mileage and fuel consumption will be based on tripmeter A. • Current fuel mileage: Current instant fuel mileage. If your speed is less than 7 km/h (5 mph), “ ” is displayed. When “ ” is displayed at speeds above 7 km/h (5 mph), go to your dealer for service. • Average fuel mileage: Average fuel mileage since tripmeter A was reset. When “ ” is displayed, go to your dealer for service. • Fuel consumption: Total fuel consumption since tripmeter A was reset. When “ ” is displayed, go to your dealer for service. u To reset the average fuel mileage and fuel consumption: (P24) continued 23 13 CB500F-32MGZA000.book 24 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments (Continued) ❙ To reset the tripmeter, average fuel mileage and fuel consumption Operation Guide !a To reset tripmeter A, average fuel mileage, and fuel consumption together, press and hold SET button. Tripmeter A Average fuel Fuel mileage consumption or !c Then, the display returns to the last selected indication. or or !d To reset tripmeter B, press and hold SET button with tripmeter B displayed. Tripmeter B or !b When they are reset, “0.0” is displayed at each indication. Also, the tripmeter A, average fuel mileage, and fuel consumption will automatically reset by refuelling more than the reserve amount and riding your motorcycle for 0.1 km (0.06 mile). You can activate or deactivate the automatic reset mode by refuelling. (P26) 24 13 CB500F-32MGZA000.book 25 ページ ２０１２年１１月２７日 Reserve fuel consumption meter Reserve fuel consumption meter 午後３時５７分 • Flashes from “0.0” L (litre) or gal (US gal). u When the amount of consumed fuel is more than 1.0 litre (0.26 US gal, 0.22 Imp gal) the display blinks faster. u If you change the display to odometer, tripmeter, fuel mileage meter and fuel consumption meter and so on (P22), it will automatically return to the reserve fuel consumption display if the buttons are not pressed after for about 10 seconds. Operation Guide When the 1st (E) segment of the fuel gauge starts flashing, the odometer & tripmeter & fuel mileage meter & fuel consumption meter switches to the reserve fuel consumption. You should refill the tank as soon as possible. 火曜日 After refuelling more than the reserve amount, the display returns to normal when your motorcycle travel 0.1 km (0.06 mile). continued 25 13 CB500F-32MGZA000.book 26 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments (Continued) Operation Guide Display Setting Following items to change sequentially • Clock setting • Backlight brightness adjustment • Activating/deactivating of tripmeter A, average fuel mileage and fuel consumption automatic reset mode • Setting of HISS Indicator • E, II E type only Changing of speed and mileage unit • Changing of fuel mileage meter unit Press and hold SEL button and SET button Press SET button Ordinary display Setting Mode Clock setting Backlight brightness adjustment Activating/deactivating of tripmeter A, average fuel mileage and fuel consumption automatic reset mode Setting of HISS Indicator Changing of speed and mileage unit E, II E type only Changing of fuel mileage meter unit 26 13 CB500F-32MGZA000.book 27 ページ ２０１２年１１月２７日 1 To set the clock: !a Turn the ignition switch to ON. !b Press and hold SEL button and SET button until the hour digits start flashing. !c Press SEL button until the desired hour is displayed. u Press and hold to advance the hour fast. 午後３時５７分 !d Press SET button. The minute digits start flashing. !e Press SEL button until the desired minute is displayed. u Press and hold to advance the minute fast. Operation Guide In addition, to move the ordinary display at display setting. • The button is not pressed for about 30 seconds • Turn the ignition switch off and then on 火曜日 !f Press SET button. The clock is set, and then the display moves to the backlight brightness adjustment. continued 27 13 CB500F-32MGZA000.book 28 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments (Continued) 2 Backlight brightness adjustment: You can adjust the brightness five levels. Operation Guide 28 !a Press SEL button. The brightness is switched. !b Press SET button. The backlight is set, and then the display moves to the activating/ deactivating of tripmeter A, average fuel mileage and fuel consumption automatic reset mode. 13 CB500F-32MGZA000.book 29 ページ ２０１２年１１月２７日 !a Press SEL button to select “ ”(activate) or “ ” (deactivate) in the automatic reset mode. 午後３時５７分 !b To end the selection, press SET button. The activation/deactivation of automatic reset mode is set, and then the display moves to the on/off of blinks of HISS indicator (HISS indicator comes on). Operation Guide 3 To activate/deactivate of tripmeter A, average fuel mileage and fuel consumption automatic reset mode: You can also activate or deactivate the automatic reset mode by refuelling after 1st (E) segment of the fuel gauge starts flashing. Deactivation is initially set. 火曜日 continued 29 13 CB500F-32MGZA000.book 30 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments (Continued) Operation Guide 4 HISS indicator setting: You can select the blink or off the HISS indicator. !a Press SEL button to select “ “ ” (off). ”(blinks) or !b Except E, II E type Press SET button. The HISS indicator setting is set, and then the display moves to the changing of the fuel mileage meter unit. E, II E type only Press SET button. The HISS indicator is set, and then the display moves to the changing of the speed and mileage unit. 30 5 Changing the speed and mileage unit: E, II E type only !a Press SEL button to select either “km/h” and “km” or “mph” and “mile”. !b Press SET button. The speed and mileage unit is set, and then the display moves to the changing of the fuel mileage meter unit. 13 CB500F-32MGZA000.book 31 ページ ２０１２年１１月２７日 6 Changing the fuel mileage meter unit: E, II E type only If the “mph” for speed and “mile” for mileage are selected, the fuel mileage shown by “mile/L” or “mile/gal”. 午後３時５７分 !b To end the selection, press SET button. The established setting can also be set by turning the ignition switch to OFF. The control is automatically switched from the setting mode to the ordinary display if the button is not pressed for about 30 seconds. Even in this case, established setting is maintained. Operation Guide !a Press SEL button to select “km/L” or “L/100 km”. 火曜日 31 13 CB500F-32MGZA000.book 32 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Indicators Operation Guide Low oil pressure indicator Comes on when the ignition switch is turned on. Goes off when the engine starts. If it comes on while engine is running: (P87) ABS (Anti-lock Brake System) indicator (CB500FA only) Comes on when the ignition switch is turned on. Goes off when your speed reaches approximately 10 km/h (6 mph). If it comes on while riding: (P88) High coolant temperature indicator Comes on briefly when the ignition switch is turned on. If it comes on while riding: (P86) PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) Comes on briefly when the ignition switch is turned on with the engine stop switch in the (Run) position. Comes on when the ignition switch is turned on with the engine stop switch in the (Off) position. If it comes on while engine is running: (P87) 32 13 CB500F-32MGZA000.book 33 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Operation Guide HISS indicator (P26) (P106) • Comes on briefly when the ignition switch is turned on. Goes off if the ignition key has the correct coding. • Flashes every 2 seconds for 24 hours when the ignition switch is turned off. Right turn signal indicator High beam indicator Left turn signal indicator Neutral indicator Comes on when the transmission is in Neutral. 33 13 CB500F-32MGZA000.book 34 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Switches Operation Guide Engine stop switch Should normally remain in the (Run) position. u In an emergency, switch to the (Off) position to stop the engine. Start button Horn button Turn signal switch u Pressing the switch turns the turn signal off. Headlight dimmer switch • : High beam • : Low beam Passing light control switch Flashes the high beam headlight. 34 Hazard switch Switchable when the ignition switch is on. Can be turned to off regardless of the ignition switch position. u The signals continue flashing with the ignition switch is OFF or LOCK after the hazard switch is on. 13 CB500F-32MGZA000.book 35 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 ON Turns electrical system on for starting/riding. OFF Turns engine off. u Key can be removed when in the OFF or LOCK position. LOCK Locks steering. Steering Lock ❙ Locking Lock the steering when parking to help prevent theft. !a Turn the handlebar all the way to the left. A U-shaped wheel lock or similar device is also recommended. Ignition key !a Push !b Turn Operation Guide Ignition Switch Switches the electrical system on/off, locks the steering. !b Push the key down, and turn the ignition switch to the LOCK position. u Jiggle the handlebar if the lock is difficult to engage. !c Remove the key. ❙ Unlocking Insert the key, push it in, and turn the ignition switch to the OFF position. 35 13 CB500F-32MGZA000.book 36 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Starting the Engine Operation Guide Start your engine using the following procedure, regardless of whether the engine is cold or warm. !a Make sure the engine stop switch is in the (Run) position. !c !c Shift the transmission to Neutral ( N indicator comes on). Alternatively, pull in the clutch lever to start your motorcycle with the transmission in gear so long as the side stand is raised. !a !d !b NOTICE • If the engine does not start within 5 seconds, turn the ignition off and wait 10 seconds before trying to start the engine again for recovery of battery voltage. • Extended fast idling and revving the engine can damage the engine, and the exhaust system. • Snapping the throttle or fast idling for more than about 5 minutes may cause exhaust pipe discolouration. !b Turn the ignition switch to the ON position. !d Press the start button with the throttle completely closed. If the engine does not start: !a Open the throttle fully and press the start button for 5 seconds. !b Repeat the normal starting procedure. !c If the engine starts, open the throttle slightly if idling is unstable. !d If the engine does not start, wait 10 seconds before trying steps !a & !b again. ❙ If Engine Will Not Start (P85) 36 13 CB500F-32MGZA000.book 37 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Shifting Gears Operation Guide Your motorcycle transmission has six forward gears in a one-down, five-up shift pattern. 6 5 4 3 2 N 1 If you put the motorcycle in gear with the side stand down, the engine will shut off. 37 13 CB500F-32MGZA000.book 38 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Refuelling Ignition key Opening the Fuel Fill Cap Fuel filler opening Operation Guide Closing the Fuel Fill Cap Lock cover Fuel fill cap Filler neck plate Fuel level (max) Do not fill with fuel above the plate. Fuel type: Unleaded petrol only Fuel octane number: Your motorcycle is designed to use Research Octane Number (RON) 91 or higher Tank capacity: 15.7 litres (4.15 US gal, 3.45 Imp gal) ❙ Refuelling and Fuel Guidelines (P15) 38 Open the lock cover, insert the ignition key, and turn it clockwise to remove the cap. !a After refuelling, align the fuel fill cap latch with the slot in the filler neck. !b Push the fuel fill cap into the filler neck until it snaps closed and locks. !c Remove the key and close the lock cover. u The key cannot be removed if the cap is not locked. 3 WARNING Petrol is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine, and keep heat, sparks, and flame away. • Handle fuel only outdoors. • Wipe up spills immediately. 13 CB500F-32MGZA000.book 39 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Storage Equipment The helmet holder and helmet set wire (in the tool kit) are located under the rear seat. Helmet holder Riding with a helmet attached to the holder can interfere with your ability to safely operate the motorcycle and could lead to a crash in which you can be seriously hurt or killed. Helmet set wire Operation Guide 3 WARNING Use the helmet holder only while parked. Do not ride with a helmet secured by the holder. u Use the helmet holder only when parked. ❙ Removing the Rear Seat (P58) continued 39 13 CB500F-32MGZA000.book 40 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Storage Equipment (Continued) The tool kit is located under the rear seat. There is also space to store a U-shaped lock. Operation Guide Rubber strap The document bag is located underside of the front seat. Document bag Tool kit Rubber strap U-shaped lock u The U-shaped lock is held in place under the front seat. u Some U-shaped locks may not fit in the compartment due to their size or design. 40 ❙ Removing the Front Seat (P59) 13 CB500F-32MGZA000.book 41 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully before attempting any maintenance. Refer to “Specifications” for service data. Importance of Maintenance ..................... P. 42 Maintenance Schedule .............................. P. 43 Maintenance Fundamentals ..................... P. 46 Tool kit ....................................................... P. 57 Removing & Installing Body Components ..P. 58 Rear Seat .................................................. P. 58 Front Seat ................................................. P. 59 Side Cover ................................................ P. 60 Headlight Assembly .................................. P. 61 Clips ......................................................... P. 62 Battery...................................................... P. 63 Engine Oil ...................................................P. 64 Coolant .......................................................P. 68 Brakes .........................................................P. 70 Side Stand...................................................P. 72 Drive Chain .................................................P. 73 Clutch ..........................................................P. 77 Throttle .......................................................P. 80 Crankcase Breather ....................................P. 81 Other Adjustments ....................................P. 82 Rear Suspension ........................................P. 82 Headlight Aim ...........................................P. 83 Brakelight Switch ......................................P. 83 13 CB500F-32MGZA000.book 42 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Importance of Maintenance Importance of Maintenance Maintenance Keeping your motorcycle well-maintained is absolutely essential to your safety and to protect your investment, obtain maximum performance, avoid breakdowns, and reduce air pollution. Maintenance is the owner’s responsibility. Be sure to inspect your motorcycle before each ride, and perform the periodic checks specified in the Maintenance Schedule. 2 P. 43 3 WARNING Improperly maintaining your motorcycle or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual. 42 Maintenance Safety Always read the maintenance instructions before you begin each task, and make sure that you have the tools, parts, and skills required. We cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Follow these guidelines when performing maintenance. ● Stop the engine and remove the key. ● Park your motorcycle on a firm, level surface using the side stand or a maintenance stand to provide support. ● Allow the engine, muffler, brakes, and other high-temperature parts to cool before servicing as you can get burned. ● Run the engine only when instructed, and do so in a well-ventilated area. 13 CB500F-32MGZA000.book 43 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Schedule The maintenance schedule specifies the maintenance requirements necessary to ensure safe, dependable performance, and proper emission control. Honda recommends that your dealer should road test your motorcycle after each periodic maintenance is carried out. Maintenance Maintenance work should be performed in accordance with Honda’s standards and specifications by properly trained and equipped technicians. Your dealer meets all of these requirements. Keep an accurate record of maintenance to help ensure that your motorcycle is properly maintained. Make sure that whomever performs the maintenance completes this record. All scheduled maintenance is considered a normal owner operating cost and will be charged for by your dealer. Retain all receipts. If you sell the motorcycle, these receipts should be transferred with the motorcycle to the new owner. continued 43 13 CB500F-32MGZA000.book 44 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Schedule Items Pre-ride Check 2 P. 46 × 1,000 km × 1,000 mi 1 0.6 Fuel Line I Maintenance Fuel Level I Throttle Operation I I 36 24 48 32 I I Annual Regular Refer to Check Replace page – I 38 I Air Cleaner *2 I I I R R R R I I 80 I 56 Crankcase Breather *3 81 Spark Plug Valve Clearance Engine Oil I – – R R R R R R 64 Engine Oil Filter R R R R R R 66 Engine Idle Speed I I I I I I I I I I I Cooling System I I I I I – Secondary Air Supply System I I I I I – Radiator Coolant *4 I I Maintenance Level : Intermediate. We recommend service by your dealer, unless you have the necessary tools and are mechanically skilled. Procedures are provided in an official Honda Shop Manual. : Technical. In the interest of safety, have your motorcycle serviced by your dealer. 44 Frequency *1 12 24 8 16 – 3 Years Maintenance Legend I : Inspect (clean, adjust, lubricate, or replace if necessary) : Lubricate R : Replace : Clean 68 13 CB500F-32MGZA000.book 45 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Schedule Items Drive Chain Pre-ride Check 2 P. 46 × 1,000 km × 1,000 mi 1 0.6 Frequency *1 12 24 8 16 36 24 48 32 Annual Regular Refer to Check Replace page Every 1,000 km (600 mi): I I Drive Chain Slider 73 76 I I I I I I I I I I I I I 71 I I I I I 46 Brakelight Switch I I I I I 83 Headlight Aim I I I I I 83 Brake Fluid *4 I Brake Pads Wear I Brake System I Lights/Horn I Engine Stop Switch I Clutch System I Side Stand I Wheels/Tyres 70 – – I Suspension Nuts, Bolts, Fasteners 2 Years Maintenance I I I Steering Head Bearings I Notes: *1 : At higher odometer readings, repeat at the frequency interval established here. *2 : Service more frequently when riding in unusually wet or dusty areas. I I I I I 77 I I I I I 72 I I I I I 82 I I I I I – I I I I I 53 I I I I I – *3 : Service more frequently when riding in rain or at full throttle. *4 : Replacement requires mechanical skill. 45 13 CB500F-32MGZA000.book 46 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals Pre-ride Inspection Maintenance 46 To ensure safety, it is your responsibility to perform a pre-ride inspection and make sure that any problem you find is corrected. A preride inspection is a must, not only for safety, but because having a breakdown, or even a flat tyre, can be a major inconvenience. Check the following items before you ride motorcycle: ● Fuel level − Fill fuel tank when necessary. 2 P. 38 ● Throttle − Check for smooth opening and full closing in all steering positions. 2 P. 80 ● Engine oil level − Add engine oil if necessary. Check for leaks. 2 P. 64 ● Coolant level − Add coolant if required. Check for leaks. 2 P. 68 Drive chain − Check condition and slack, adjust and lubricate if necessary. 2 P. 73 ● Brakes − Check operation; Front and Rear: check brake fluid level and pads wear. 2 P. 70, 71 ● Lights and horn − Check that lights, indicators and horn function properly. ● Engine stop switch − Check for proper function. ● Clutch − Check operation; Adjust freeplay if necessary. 2 P. 77 ● Side stand ignition cut-off system − Check for proper function. 2 P. 72 ● Wheels and tyres − Check condition, air pressure and adjust if necessary. 2 P. 53 ● 13 CB500F-32MGZA000.book 47 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals Replacing Parts Always use Honda Genuine Parts or their equivalents to ensure reliability and safety. Colour label Maintenance When ordering coloured components, specify the model name, colour, and code mentioned on the colour label. The colour label is attached to the rear fender under the rear seat. 2 P. 58 3 WARNING Installing non-Honda parts may make your motorcycle unsafe and cause a crash in which you can be seriously hurt or killed. Always use Honda Genuine Parts or equivalents that have been designed and approved for your motorcycle. 47 13 CB500F-32MGZA000.book 48 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals Battery Maintenance Your motorcycle has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water. Clean the battery terminals if they become dirty or corroded. Do not remove the battery cap seals. There is no need to remove the cap when charging. NOTICE Your battery is a maintenance-free type and can be permanently damaged if the cap strip is removed. This symbol on the battery means that this product must not be treated as household waste. NOTICE An improperly disposed of battery can be harmful to the environment and human health. Always confirm local regulations for battery disposal. 48 3 WARNING The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled mechanic do the battery servicing. ❙ Cleaning the Battery Terminals 1. Remove the battery. 2 P. 63 2. If the terminals are starting to corrode and are coated with a white substance, wash with warm water and wipe clean. 13 CB500F-32MGZA000.book 49 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals 3. If the terminals are heavily corroded, clean and polish the terminals with a wire brush or sandpaper. Wear safety glasses. Fuses ❙ Inspecting and Replacing Fuses 4. After cleaning, reinstall the battery. The battery has a limited life span. Consult your dealer about when you should replace the battery. Always replace the battery with another maintenance-free battery of the same type. NOTICE Installing non-Honda electrical accessories can overload the electrical system, discharging the battery and possibly damaging the system. Turn off the ignition switch to remove and inspect fuses. If a fuse is blown, replace with a fuse of the same rating. For fuse ratings, see “Specifications.” 2 P. 118 Maintenance Fuses protect the electrical circuits on your motorcycle. If something electrical on your motorcycle stops working, check for and replace any blown fuses. 2 P. 102 Blown fuse NOTICE Replacing a fuse with one that has a higher rating greatly increases the chance of damage to the electrical system. continued 49 13 CB500F-32MGZA000.book 50 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals If a fuse fails repeatedly, you likely have an electrical fault. Have your motorcycle inspected by your dealer. *1. Engine Oil Maintenance Engine oil consumption varies and oil quality deteriorates according to riding conditions and time elapsed. Check the engine oil level regularly, and add the recommended engine oil if necessary. Dirty oil or old oil should be changed as soon as possible. ❙ Selecting the Engine Oil For recommended engine oil, see “Specifications.” 2 P. 117 If you use non-Honda engine oil, check the label to make sure that the oil satisfies all of the following standards: ● JASO T 903 standard*1: MA ● SAE standard*2: 10W-30 ● API classification*3: SG or higher 50 The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines. There are two classes: MA and MB. For example, the following label shows the MA classification. Oil code Oil classification *2. *3. The SAE standard grades oils by their viscosity. The API classification specifies the quality and performance rating of engine oils. Use SG or higher oils, excluding oils marked as “Energy Conserving” or ”Resource Conserving” on the circular API service symbol. Not recommended Recommended 13 CB500F-32MGZA000.book 51 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals Brake Fluid NOTICE Brake fluid can damage plastic and painted surfaces. Wipe up spills immediately and wash thoroughly. Also inspect the engine sprocket and rear wheel sprocket. If either has worn or damaged teeth, have the sprocket replaced by your dealer. Maintenance Do not add or replace brake fluid, except in an emergency. Use only fresh brake fluid from a sealed container. If you do add fluid, have the brake system serviced by your dealer as soon as possible. If the chain does not move smoothly, makes strange noises, has damaged rollers or loose pins or missing O-rings, or kinks, have the chain inspected by your dealer. Recommended brake fluid: Honda DOT 4 Brake Fluid or equivalent Normal (GOOD) Worn (REPLACE) Damaged (REPLACE) Drive Chain The drive chain must be inspected and lubricated regularly. Inspect the chain more frequently if you often ride on bad roads, ride at high speed, or ride with repeated fast acceleration. NOTICE Use of a new chain with worn sprockets will cause rapid chain wear. continued 51 13 CB500F-32MGZA000.book 52 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals ❙ Cleaning and Lubricating Maintenance After inspecting the slack, clean the chain and sprockets while rotating the rear wheel. Use dry cloth with chain cleaner designed specifically for O-ring chains, or neutral detergent. Use a soft brush if the chain is dirty. After cleaning, wipe dry and lubricate with the recommended lubricant. If not available, use SAE 80 or 90 gear oil. Recommended lubricant: Drive chain lubricant designed specifically for O-ring chains. Do not use a steam cleaner, a high pressure cleaner, a wire brush, volatile solvent such as petrol and benzene, abrasive cleaner, chain cleaner or lubricant NOT designed specifically for O-ring chains as these can damage the rubber O-ring seals. Avoid getting lubricant on the brakes or tyres. Avoid applying excess chain lubricant to prevent spray onto your clothes and the motorcycle. Recommended Coolant Pro Honda HP coolant is a pre-mixed solution of antifreeze and distilled water. Concentration: 50% antifreeze and 50% distilled water A concentration of antifreeze below 40% will not provide proper corrosion and cold temperature protection. 52 13 CB500F-32MGZA000.book 53 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals A concentration of up to 60% will provide better protection in colder climates. Crankcase Breather Service more frequently when riding in rain, at full throttle, or after the motorcycle is washed or overturned. Service if the deposit level can be seen in the transparent section of the drain tube. Tyres (Inspecting/Replacing) ❙ Checking the Air Pressure Inspect the tyres for cuts, slits, or cracks that exposes fabric or cords, or nails or other foreign objects embedded in the side of the tyre or the tread. Also inspect for the bumps or bulges in the side walls of the tyres. Maintenance NOTICE Using coolant not specified for aluminium engines or ordinary tap water can cause corrosion. ❙ Inspecting for Damage ❙ Inspecting for Abnormal Wear Inspect the tyres for signs of abnormal wear on the contact surface. Visually inspect your tyres and use an air pressure gauge to measure the air pressure at least once a month or any time you think the tyres look low. Always check air pressure when your tyres are cold. continued 53 13 CB500F-32MGZA000.book 54 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals ❙ Inspecting Tread Depth Inspect the tread wear indicators. If they become visible, replace the tyres immediately. For safe riding, you should replace the tyres when the minimum tread depth is reached. Maintenance or TWI Wear indicator location mark 54 3 WARNING Riding on tyres that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tyre inflation and maintenance. Germany German law prohibits use of tyres whose tread depth is less than 1.6 mm. 13 CB500F-32MGZA000.book 55 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Maintenance Fundamentals 3 WARNING Installing improper tyres on your motorcycle can adversely affect handling and stability, and can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tyres recommended in this owner’s manual. Maintenance Have your tyres replaced by your dealer. For recommended tyres, air pressure and minimum tread depth, see “Specifications.” 2 P. 117 Follow these guidelines whenever you replace tyres. ● Use the recommended tyres or equivalents of the same size, construction, speed rating, and load range. ● Have the wheel balanced with Honda Genuine balance weights or equivalents after the tyre is installed. ● Do not install a tube inside a tubeless tyre on this motorcycle. Excessive heat build-up can cause the tube to burst. ● Use only tubeless tyres on this motorcycle. The rims are designed for tubeless tyres, and during hard acceleration or braking, a tubetype tyre could slip on the rim and cause the tyre to rapidly deflate. 55 13 CB500F-32MGZA000.book 56 ページ ２０１２年１１月２７日 Maintenance Fundamentals Air Cleaner Maintenance 56 This motorcycle is equipped with a viscous type air cleaner element. Air blow cleaning or any other cleaning can degrade the viscous element performance and cause the intake of dust. Do not perform the maintenance. Should be serviced by your dealer. 火曜日 午後３時５７分 13 CB500F-32MGZA000.book 57 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tool kit The tool kit is stored under the rear seat. 2 P. 58 U type only Pin spanner 8 × 12 mm Open end wrench ● 10 × 14 mm Open end wrench ● Standard/Phillips screwdriver ● Screwdriver handle ● Extension bar ● 5 mm Hex wrench ● 19 mm Box end wrench ● 24 mm Box end wrench ● Helmet set wire ● Fuse puller ● ● Except U type Pin spanner 10 × 14 mm Open end wrench ● Standard/Phillips screwdriver ● Screwdriver handle ● Extension bar ● 5 mm Hex wrench ● Helmet set wire ● Fuse puller ● ● Maintenance You can perform some roadside repairs, minor adjustments and parts replacement with the tools contained in the kit. 57 13 CB500F-32MGZA000.book 58 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Removing & Installing Body Components ❙ Removal Rear Seat Ignition key Seat lock Maintenance Prongs 1. Insert the ignition key into the seat lock. 2. Turn it clockwise, then pull the rear seat up and back. ❙ Installation 1. Insert the prongs into the rear stays on the frame. 2. Push down on the rear of the rear seat. Make sure that the seat is locked securely in position to pull it up lightly. The seat locks automatically when closed. Take care not to lock your key in the compartment under the rear seat. Rear stays 58 Rear seat 13 CB500F-32MGZA000.book 59 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Removing & Installing Body Components u Front Seat ❙ Removal Front Seat Front seat Mounting bolts Collars ❙ Installation 1. Insert the tab into the recess. 2. Install the collars and mounting bolts. 3. Tighten the mounting bolts securely. Make sure that the seat is locked securely in position to pull it up lightly. Maintenance Tab 1. Remove the rear seat. 2 P. 58 2. Remove the mounting bolts and collars, and then pull the front seat back and up. Recess 59 13 CB500F-32MGZA000.book 60 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Removing & Installing Body Components u Side Cover Side Cover Side cover Grommets Prongs The left side cover must be removed to access the coolant reserve tank cap. The right side cover must be removed to access the main fuse. Maintenance The right and left side covers can be removed in the same manner. ❙ Removal 1. Remove the bolt and clip. 2 P. 62 2. Remove the prongs from the grommets. 3. Remove the side cover by releasing the tabs. ❙ Installation Prongs Bolt Clip 60 Tabs Install the parts in the reverse order of removal. 13 CB500F-32MGZA000.book 61 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Removing & Installing Body Components u Headlight Assembly Headlight Assembly Bolts Headlight assembly The headlight assembly must be removed to replace the headlight bulb and position light bulb. ❙ Removal Maintenance When removing and installing the headlight assembly, be careful not to damage the wire harness. 1. Remove the bolts. 2. Remove the headlight assembly by releasing it from the holes of the bottom bridge. ❙ Installation Install the parts in the reverse order of removal. Holes 61 13 CB500F-32MGZA000.book 62 ページ ２０１２年１１月２７日 Removing & Installing Body Components u Clips Clips The clips must be removed to remove the side covers. Maintenance ❙ Removal 1. Press down on the centre pin to release the lock. 2. Pull the clip out of the hole. Centre pin ❙ Installation 1. Push the bottom of the centre pin. 2. Insert the clip into the hole. 3. Press down on the centre pin to lock the clip. 62 火曜日 午後３時５７分 13 CB500F-32MGZA000.book 63 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Removing & Installing Body Components u Battery Battery Positive terminal Rubber strap Battery ❙ Removal Make sure the ignition switch is off. 1. Remove the front seat. 2 P. 59 ❙ Installation Install the parts in the reverse order of removal. Always connect the positive + terminal first. Make sure that bolts and nuts are tight. Readjust the clock after the battery is reconnected since the clock goes wrong once the battery disconnected. The tripmeter A and B will be reset if the battery is disconnected. For proper handling of the battery, see “Maintenance Fundamentals.” 2 P. 48 Battery Goes Dead 2 P. 97 Maintenance Negative terminal 2. Unhook the rubber strap from rear side. 3. Disconnect the negative - terminal from the battery. 4. Disconnect the positive + terminal from the battery. 5. Remove the battery taking care not to drop the terminal nuts. 63 13 CB500F-32MGZA000.book 64 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Engine Oil Checking the Engine Oil Maintenance 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait 2 to 3 minutes. 3. Place your motorcycle in an upright position on a firm, level surface. 4. Check that the oil level is between the upper and lower level marks in the oil level inspection window. Oil fill cap Oil level inspection window Upper level Lower level 64 13 CB500F-32MGZA000.book 65 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Engine Oil u Adding Engine Oil Adding Engine Oil For the recommended oil and oil selection guidelines, see “Maintenance Fundamentals.” 2 P. 50 Maintenance If the engine oil is below or near the lower level mark, add the recommended engine oil. 2 P. 50 1. Remove the oil fill cap. Add the recommended oil until it reaches the upper level mark. u Place your motorcycle in an upright position on a firm, level surface when checking the oil level. u Do not overfill above the upper level mark. u Make sure no foreign objects enter the oil filler opening. u Wipe up any spills immediately. 2. Securely reinstall the oil fill cap. NOTICE Overfilling with oil or operating with insufficient oil can cause damage to your engine. Do not mix different brands and grades of oil. They may affect lubrication and clutch operation. 65 13 CB500F-32MGZA000.book 66 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Engine Oil u Changing Engine Oil & Filter Changing Engine Oil & Filter Maintenance Changing the oil and filter requires special tools. We recommend that you have your motorcycle serviced by your dealer. Use a new Honda Genuine oil filter or equivalent specified for your model. NOTICE Using the wrong oil filter can result in serious damage to the engine. 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait for 2 to 3 minutes. 3. Park on a firm, level surface and lower the side stand. 4. Place a drain pan under the drain bolt. 66 Drain bolt Sealing washer 5. Remove the oil fill cap, drain bolt, and sealing washer to drain the oil. 6. Remove the oil filter with a filter wrench and let the remaining oil drain out. Make sure the prior seal is not stuck to the engine. u Discard the oil and oil filter at an approved recycling centre. 13 CB500F-32MGZA000.book 67 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Engine Oil u Changing Engine Oil & Filter Oil filter 9. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft). Rubber seal 7. Apply a thin coat of engine oil to the rubber seal of a new oil filter. 8. Install a new oil filter and tighten. Torque: 26 N·m (2.7 kgf·m, 19 lbf·ft). Required oil When changing oil & engine oil filter: 2.7 litres (2.9 US qt, 2.4 Imp qt) When changing oil only: 2.5 litres (2.6 US qt, 2.2 Imp qt) Maintenance 10. Fill the crankcase with the recommended oil (2 P. 50) and install the oil fill cap. 11. Check the oil level. 2 P. 64 12. Check that there are no oil leaks. 67 13 CB500F-32MGZA000.book 68 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Coolant Checking the Coolant Maintenance 1. Place your motorcycle on a firm, level surface. 2. Hold your motorcycle in an upright position. 3. Check that the coolant level is between the UPPER and LOWER level marks in the reserve tank. UPPER level Reserve tank 68 LOWER level If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a serious leak. Have your motorcycle inspected by your dealer. Adding Coolant If the coolant level is below the LOWER level, add the recommended coolant (2 P. 52) until the level reaches the UPPER level mark. Add fluid only from the reserve tank cap and do not remove radiator cap. 1. Remove the left side cover. 2 P. 60 13 CB500F-32MGZA000.book 69 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Coolant u Changing Coolant Reserve tank cap Maintenance 2. Remove the reserve tank cap and add fluid while monitoring the coolant level. u Do not overfill above the UPPER level mark. u Make sure no foreign objects enter the reserve tank opening. 3. Securely reinstall the cap. 4. Install the left side cover. 3 WARNING Removing the radiator cap while the engine is hot can cause the coolant to spray out, potentially scalding you. Always let the engine and radiator cool down before removing the radiator cap. Changing Coolant Have your dealer change the coolant unless you have the proper tools and are mechanically qualified. 69 13 CB500F-32MGZA000.book 70 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Brakes Checking Brake Fluid Maintenance 1. Place your motorcycle in an upright position on a firm, level surface. 2. Front Check that the brake fluid reservoir is horizontal and that the fluid level is above the LWR mark. Rear Check that the brake fluid reservoir is horizontal and that the fluid level is between the LOWER level and UPPER level marks. Front If the brake fluid level in either reservoir is below the LWR or LOWER level mark or the brake lever and pedal freeplay becomes excessive, inspect the brake pads for wear. If the brake pads are not worn, you most likely have a leak. Have your motorcycle inspected by your dealer. Rear Front brake fluid reservoir Rear brake fluid reservoir UPPER level mark LOWER level mark LWR mark 70 13 CB500F-32MGZA000.book 71 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Brakes u Inspecting the Brake Pads Inspecting the Brake Pads Front Maintenance Check the condition of the brake pad groove wear indicators. The pads need to be replaced if a brake pad is worn to the indicator. 1. Front Inspect the brake pads from below the brake caliper. 2. Rear Inspect the brake pads from the rear right of the motorcycle. If necessary have the pads replaced by your dealer. Always replace both left and right brake pads at the same time. Rear Pads Wear indicator Disc Pads Wear indicator Wear indicator Wear indicator Disc 71 13 CB500F-32MGZA000.book 72 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Side Stand Maintenance 4. Start the engine, pull the clutch lever in, and shift the transmission into gear. 5. Lower the side stand all the way. The engine should stop as you lower the side stand. If the engine doesn’t stop, have your motorcycle inspected by your dealer. Side stand spring 1. Check that the side stand operates smoothly. If the side stand is stiff or squeaky, clean the pivot area and lubricate the pivot bolt with clean grease. 2. Check the spring for damage or loss of tension. 3. Sit on the motorcycle, put the transmission in Neutral, and raise the side stand. 72 13 CB500F-32MGZA000.book 73 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Drive Chain Inspecting the Drive Chain Slack Drive chain slack: 35 to 45 mm (1.4 to 1.8 in) Maintenance Check the drive chain slack at several points along the chain. If the slack is not constant at all points, some links may be kinked and binding. Have the chain inspected by your dealer. 1. Place your motorcycle on the side stand on a level surface. 2. Stop the engine. Place the transmission in Neutral. 3. Check the slack in the lower half of the drive chain midway between the sprockets. 4. Roll the motorcycle forward and check that the chain moves smoothly. 5. Inspect the sprockets. 2 P. 51 6. Clean and lubricate the drive chain. 2 P. 52 u Do not ride your motorcycle if the slack exceeds 60 mm (2.4 in). 73 13 CB500F-32MGZA000.book 74 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Drive Chain u Adjusting the Drive Chain Slack Adjusting the Drive Chain Slack Lock nut Rear axle nut Maintenance Adjusting the chain requires special tools. Have the drive chain slack adjusted by your dealer. (CB500FA only) When adjusting the drive chain slack, be careful not to damage the wheel speed sensor and pulser ring. Adjusting nut 1. Place your motorcycle on the side stand on a level surface. 2. Stop the engine. Place the transmission in Neutral. 3. Loosen the rear axle nut. 4. Loosen the lock nuts on both sides of the swingarm. Rear edge of adjusting slot Chain adjuster index mark Adjusting nut 74 Lock nut 13 CB500F-32MGZA000.book 75 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Drive Chain u Adjusting the Drive Chain Slack 7. Tighten the rear axle nut. Torque: 88 N·m (9.0 kgf·m, 65 lbf·ft). 8. Tighten the drive chain adjusting nuts lightly, then hold the adjusting nuts and tighten the lock nuts. Torque: 21 N·m (2.1 kgf·m, 15 lbf·ft). 9. Recheck drive chain slack. Maintenance 5. Turn both adjusting nuts an equal number of turns until the correct drive chain slack is obtained. Turn the adjusting nuts clockwise to tighten the chain. Turn the adjusting nuts counterclockwise to provide more slack. Adjust the slack at a point midway between the front sprocket and the rear wheel sprocket. Check the drive chain slack. 2 P. 73 6. Check rear axle alignment by making sure the chain adjuster index marks align with the rear edge of the adjusting slots. Both marks should correspond. If the axle is misaligned, turn the right or left adjusting nuts until the marks are aligned and recheck chain slack. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. continued 75 13 CB500F-32MGZA000.book 76 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Drive Chain u Checking the Drive Chain Slider Maintenance ❙ Checking the Drive Chain Wear Checking the Drive Chain Slider Check the chain wear label when adjusting the drive chain. If the index mark on the washer enters the red zone on the label after the chain has been adjusted to the proper slack, the chain is excessively worn and must be replaced. Check the condition of the drive chain slider. The drive chain slider need to be replaced if it is worn to the wear limit line. If necessary have the drive chain slider replaced by your dealer. Chain: DID 520V0 If necessary have the drive chain replaced by your dealer. Wear limit line Red zone Index mark 76 Drive chain slider 13 CB500F-32MGZA000.book 77 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Clutch Checking the Clutch ❙ Checking the Clutch Lever Freeplay Check the clutch lever freeplay. Clutch lever Maintenance Freeplay at the clutch lever: 10 to 20 mm (0.4 to 0.8 in) Check the clutch cable for kinks or signs of wear. If necessary have it replaced by your dealer. Lubricate the clutch cable with a commercially available cable lubricant to prevent premature wear and corrosion. Freeplay 77 13 CB500F-32MGZA000.book 78 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Clutch u Adjusting the Clutch Lever Freeplay Adjusting the Clutch Lever Freeplay Upper clutch cable adjuster ❙ Upper Adjustment Maintenance – Attempt adjustment with the upper clutch cable adjuster first. 1. Loosen the upper lock nut. 2. Turn the upper clutch cable adjuster until the freeplay is 10 to 20 mm (0.4 to 0.8 in). 3. Tighten the upper lock nut and check the freeplay again. + Upper lock nut ❙ Lower Adjustment If the upper clutch cable adjuster is threaded out near its limit, or the correct freeplay cannot be obtained, attempt adjustment with the lower adjusting nut. 78 13 CB500F-32MGZA000.book 79 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Clutch u Adjusting the Clutch Lever Freeplay Lower lock nut + – Maintenance 1. Loosen the upper lock nut and turn the upper clutch cable adjuster all the way in (to provide maximum freeplay). Tighten the upper lock nut. 2. Loosen the lower lock nut. 3. Turn the lower adjusting nut until the clutch lever freeplay is 10 to 20 mm (0.4 to 0.8 in). 4. Tighten the lower lock nut and check the clutch lever freeplay. 5. Start the engine, pull the clutch lever in, and shift into gear. Make sure the engine does not stall and the motorcycle does not creep. Gradually release the clutch lever and open the throttle. Your motorcycle should move smoothly and accelerate gradually. Lower adjusting nut If proper adjustment cannot be obtained or the clutch does not work correctly, see your dealer. 79 13 CB500F-32MGZA000.book 80 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Throttle Maintenance Checking the Throttle Adjusting the Throttle Freeplay With the engine off, check that the throttle rotates smoothly from fully closed to fully open in all steering positions and throttle freeplay is correct. If the throttle does not move smoothly, close automatically, or if the cable is damaged, have the motorcycle inspected by your dealer. 1. Slide the cable boot. 2. Loosen the lock nut. 3. Turn the adjuster until the freeplay is 2 to 6 mm (0.1 to 0.2 in). 4. Tighten the lock nut and return the cable boot, then inspect the throttle action again. Freeplay at the throttle grip flange: 2 to 6 mm (0.1 to 0.2 in). Lock nut Cable boot Freeplay – Flange + Throttle grip 80 Adjuster 13 CB500F-32MGZA000.book 81 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Crankcase Breather Cleaning the Crankcase Breather Maintenance 1. Remove the crankcase breather tube plug from the tube. 2. Drain deposits into a suitable container. 3. Install the crankcase breather tube plug. Crankcase breather tube plug 81 13 CB500F-32MGZA000.book 82 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Other Adjustments Adjusting the Rear Suspension ❙ Spring Preload Maintenance You can adjust the spring preload by the adjuster to suit the load or the road surface. Turn the adjuster using the pin spanner and extension bar provided in the tool kit (2 P. 57). The preload adjuster has 9 positions. The standard position is 3 when the index mark on the adjuster is aligned with the left end of the rear shock absorber lower mounting bolt. Turn the adjuster in the direction A to decrease spring preload (soft) (position 1 to 2), or turn the adjuster in the direction B to increase spring preload (hard) (position 4 to 9). Attempting to adjust directly from 1 to 9 or 9 to 1 may damage the shock absorber. Index mark A B Adjuster Lower mounting bolt Align (Standard position) Extension bar Pin spanner 82 13 CB500F-32MGZA000.book 83 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Other Adjustments u Adjusting the Headlight Aim Adjusting the Headlight Aim Check the operation of the brakelight switch. Hold the brakelight switch and turn the adjusting nut in the direction A if the switch operates too late, or turn the nut in the direction B if the switch operates too soon. Brakelight switch Maintenance You can adjust vertical aim of the headlight for proper alignment. Turn the pinion using a Phillips screwdriver provided in the tool kit (2 P. 57) in or out as necessary. Obey local laws and regulations. Adjusting the Brakelight Switch Raise Pinion B A Lower Adjusting nut 83 13 CB500F-32MGZA000.book 84 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Troubleshooting Engine Will Not Start (HISS indicator stays on) ......................................................... P. 85 Overheating (High coolant temperature indicator is on)..........................................P. 86 Warning Indicators On or Flashing ...........P. 87 Low Oil Pressure Indicator..........................P. 87 PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) ............P. 87 ABS (Anti-lock Brake System) Indicator (CB500FA only)........................................P. 88 Other Warning Indication ......................... P. 89 Fuel Gauge Failure Indication .................... P. 89 Tyre Puncture............................................. P. 90 Electrical Trouble ....................................... P. 97 Battery Goes Dead .................................... P. 97 Burned-out Light Bulb............................... P. 97 Blown Fuse ............................................. P. 102 13 CB500F-32MGZA000.book 85 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Engine Will Not Start (HISS indicator stays on) ❙ Starter Motor Operates But Engine Does Not Start ❙ Starter Motor Does Not Operate Check the following items: ● Make sure engine stop switch is (Run) position 2 P. 34 ● Check for a blown fuse 2 P. 102 ● Check for a loose battery connection or battery terminal corrosion 2 P. 63 ● Check the condition of the battery 2 P. 97 If the problem continues, have your motorcycle inspected by your dealer. Troubleshooting Check the following items: ● Check the correct engine starting sequence 2 P. 36 ● Check that there is petrol in the fuel tank ● Check if the PGM-FI malfunction indicator lamp (MIL) is on u If the indicator light is on, contact your dealer as soon as possible. ● Check if the HISS indicator stays on u Turn the ignition switch to the OFF position and remove the key. Reinsert the key and turn the ignition switch to the ON position. If the indicator still stays on, check the following: Check if there is no another HISS key (including spare key) close to the ignition switch. Check if there are no any metallic seals or stickers on the key. If the HISS indicator still stays on, have your motorcycle inspected by your dealer. 85 13 CB500F-32MGZA000.book 86 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Overheating (High coolant temperature indicator is on) Troubleshooting The engine is overheating when the following occurs: ● High coolant temperature indicator comes on ● Acceleration becomes sluggish ● If this occurs, pull safely to the side of the road and perform the following procedure. Extended fast idling may cause the high coolant temperature indicator comes on. NOTICE Continuing to ride with an overheated engine can cause serious damage to the engine. 2. Check that the radiator fan is operating, and then turn the ignition switch to the OFF position. If the fan is not operating: Suspect a fault. Do not start the engine. Transport your motorcycle to your dealer. If the fan is operating: Allow the engine to cool with the ignition switch in the OFF position. 3. After the engine has cooled, inspect the radiator hose and check if there is a leak. 2 P. 68 If there is a leak: 1. Stop the engine using the ignition switch, and then turn the ignition switch to the ON position. 86 Do not start the engine. Transport your motorcycle to your dealer. 4. Check the coolant level in the reserve tank, and add coolant as necessary. 2 P. 68 5. If 1–4 check normal, you may continue riding, but closely monitor the high coolant temperature indicator. 13 CB500F-32MGZA000.book 87 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Warning Indicators On or Flashing Low Oil Pressure Indicator If the low oil pressure indicator comes on, pull safely to the side of the road and stop the engine. 1. Check the engine oil level, and add oil as necessary. 2 P. 64 2. Start the engine. u Only continue riding if the low oil pressure indicator goes off. Rapid acceleration may momentarily cause the low oil pressure indicator to come on, especially if the oil is at or near the low level. If the low oil pressure indicator stays on when the oil level is at the proper level, stop the engine and contact your dealer. PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) If the indicator comes on while riding, you may have a serious problem with the PGM-FI system. Reduce speed and have your motorcycle inspected by your dealer as soon as possible. Troubleshooting NOTICE Continuing to ride with low oil pressure can cause serious damage to the engine. If the engine oil level goes down rapidly, your motorcycle may have a leak or another serious problem. Have your motorcycle inspected by your dealer. 87 13 CB500F-32MGZA000.book 88 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Warning Indicators On or Flashing u ABS (Anti-lock Brake System) Indicator (CB500FA only) ABS (Anti-lock Brake System) Indicator (CB500FA only) Troubleshooting 88 If the indicator operates in one of the following ways, you may have a serious problem with the brake system. Reduce your speed and have your motorcycle inspected by your dealer as soon as possible. Indicator comes on or starts flashing while riding. ● Indicator does not come on when the ignition switch is in the ON position. ● Indicator does not go off at speeds above 10 km/h (6 mph). ● If the ABS indicator stays on, your brakes will continue to work as a conventional system, but without the anti-locking function. The ABS indicator may flash if you turn the rear wheel while your motorcycle is lifted off the ground. In this case, turn the ignition switch off and then on again. The ABS indicator will go off after your speed reaches 30 km/h (19 mph). 13 CB500F-32MGZA000.book 89 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Other Warning Indication Fuel Gauge Failure Indication Troubleshooting If the fuel system has an error, the fuel gauge indicators will be displayed as shown in the illustration. If these occurs, see your dealer as soon as possible. 89 13 CB500F-32MGZA000.book 90 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture Repairing a puncture or removing a wheel requires special tools and technical expertise. We recommend you have this type of service performed by your dealer. After an emergency repair, always have the tyre inspected/replaced by your dealer. Troubleshooting 90 Emergency Repair Using a Tyre Repair Kit If your tyre has a minor puncture, you can make an emergency repair using a tubeless tyre repair kit. Follow the instructions provided with the emergency tyre repair kit. Riding your motorcycle with a temporary tyre repair is very risky. Do not exceed 50 km/h (30 mph). Have the tyre replaced by your dealer as soon as possible. 3 WARNING Riding your motorcycle with a temporary tyre repair can be risky. If the temporary repair fails, you can crash and be seriously injured or killed. If you must ride with a temporary tyre repair, ride slowly and carefully and do not exceed 50 km/h (30 mph) until the tyre is replaced. Removing Wheels Follow these procedures if you need to remove a wheel in order to repair a puncture. 13 CB500F-32MGZA000.book 91 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels (CB500FA only) When removing and installing the wheel, be careful not to damage the wheel speed sensor and pulser ring. u Take care to prevent the brake caliper from scratching the wheel during removal. Tape or cloth Mounting bolts ❙ Front Wheel Troubleshooting Removal 1. Park on a firm, level surface. 2. Cover the right side of the front wheel and brake caliper with protective tape or cloth. 3. On the right side, remove the mounting bolts and brake caliper. u Support the brake caliper assembly so that it doesn’t hang from the brake hose. Do not twist the brake hose. u Avoid getting grease, oil, or dirt on the disc or pad surfaces. u Do not pull the brake lever while the brake caliper is removed. Brake caliper Wheel speed sensor (CB500FA only) Pulser ring (CB500FA only) Side collar continued 91 13 CB500F-32MGZA000.book 92 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels Troubleshooting 4. Loosen the axle pinch bolt and front axle shaft. 5. Support your motorcycle securely and raise the front wheel off the ground using a maintenance stand or a hoist. 6. Remove the front axle shaft, front wheel and side collars. Side collar Front axle shaft Axle pinch bolt 92 Installation 1. Attach the side collars to the wheel. 2. On the left side, place the wheel between the fork legs and insert the front axle shaft to the end, through the left fork leg and wheel hub. 3. Tighten the axle shaft. Torque: 54 N·m (5.5 kgf·m, 40 lbf·ft). 13 CB500F-32MGZA000.book 93 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels 4. Install the brake caliper and tighten the mounting bolts. Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft). NOTICE When installing the brake caliper into position on the fork leg, carefully fit the brake disc between the pads to avoid scratching them. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. Troubleshooting u Take care to prevent the brake caliper from scratching the wheel during installation. u Use new mounting bolts when installing the brake caliper. 8. Raise the front wheel off the ground again, and check that the wheel rotates freely after you release the brake. 9. Uncover the protective tape or cloth. 5. Lower the front wheel on the ground. 6. Apply the brake lever and pump the fork several times. 7. Tighten the axle pinch bolt. Torque: 22 N·m (2.2 kgf·m, 16 lbf·ft). continued 93 13 CB500F-32MGZA000.book 94 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels ❙ Rear Wheel Troubleshooting Removal 1. Support your motorcycle securely and raise the rear wheel off the ground using a maintenance stand or a hoist. 2. Loosen the rear axle nut, lock nuts and turn the adjusting nuts so the rear wheel can be moved all the way forward for maximum drive chain slack. 3. Remove the drive chain from the rear wheel sprocket by pushing the rear wheel forward. 4. Remove the rear axle nut and washer. Pulser ring (CB500FA only) Wheel speed sensor (CB500FA only) Rear axle nut Lock nut Washer Adjusting nut Rear axle shaft Lock nut Adjusting nut Drive chain 94 Washer 13 CB500F-32MGZA000.book 95 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels Installation 1. To install the rear wheel, reverse the removal procedure. u Take care to prevent the brake caliper from scratching the wheel during installation. NOTICE When installing the brake caliper into position, carefully fit the brake disc between the pads to avoid scratching them. Troubleshooting 5. Remove the rear axle shaft, washer, brake caliper bracket, rear wheel and side collars. u Support the brake caliper assembly so that it doesn’t hang from the brake hose. Do not twist the brake hose. u Avoid getting grease, oil, or dirt on the disc to pad surfaces. u Do not push the brake pedal while the wheel is removed. continued 95 13 CB500F-32MGZA000.book 96 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Tyre Puncture u Removing Wheels 2. Make sure that the slot on the brake caliper bracket is positioned in the lug on the swingarm. Brake caliper bracket Slot Torque: 88 N·m (9.0 kgf·m, 65 lbf·ft). Troubleshooting 5. Tighten the drive chain adjusting nuts lightly, then hold the adjusting nuts and tighten the lock nuts. Torque: 21 N·m (2.1 kgf·m, 15 lbf·ft). 6. After installing the wheel, apply the brake pedal several times, then recheck the wheel rotates freely. Recheck the wheel if the brake drags or if the wheel does not rotate freely. Lug Swingarm 96 3. Adjust the drive chain. 2 P. 74 4. Tighten the rear axle nut. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. 13 CB500F-32MGZA000.book 97 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble Burned-out Light Bulb Charge the battery using a motorcycle battery charger. Remove the battery from the motorcycle while charging. Do not use an automobile-type battery charger, as these can overheat a motorcycle battery and cause permanent damage. If the battery does not recover after recharging, contact your dealer. Follow the procedure below to replace a burned-out light bulb. Turn the ignition switch to the OFF or LOCK position. Allow the bulb to cool before replacing it. Do not use bulbs other than those specified. Check the replacement bulb for correct operation before riding. NOTICE Jump starting using an automobile battery is not recommended, as this can damage your motorcycle’s electrical system. For the light bulb wattage, see “Specifications.” 2 P. 118 Troubleshooting Battery Goes Dead continued 97 13 CB500F-32MGZA000.book 98 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Headlight Bulb 1. 2. 3. 4. Remove the headlight assembly. 2 P. 61 Pull off the socket without turning. Remove the dust cover. Press the pin down and pull out the bulb without turning it. 5. Install a new bulb and parts in the reverse order of removal. Pin Troubleshooting Do not touch the glass surface with your fingers. If you touch the bulb with your bare hands, clean it with a cloth moistened with alcohol. Bulb Dust cover Socket 98 13 CB500F-32MGZA000.book 99 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Position Light Bulb ❙ Brake/Tail Light Bulb Socket 1. Remove the bolts and rear fender cover. Troubleshooting Bulb 1. 2. 3. 4. Remove the headlight assembly. 2 P. 61 Pull off the socket without turning. Pull out the bulb without turning. Install a new bulb and parts in the reverse order of removal. Rear fender cover Bolts continued 99 13 CB500F-32MGZA000.book 100 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Front/Rear Turn Signal Bulb 1. Remove the screw and collar. 2. Remove the turn signal lens. 3. Slightly press the bulb and turn it counterclockwise. Troubleshooting Socket Bulb 2. Turn the socket counterclockwise, and remove it. 3. Slightly press the bulb and turn it counterclockwise. 4. Install a new bulb and parts in the reverse order of removal. 100 Collar Screw Turn signal lens Bulb 4. Install a new bulb and parts in the reverse order of removal. u Use only the amber bulb. 13 CB500F-32MGZA000.book 101 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Burned-out Light Bulb ❙ License Plate Light Bulb 1. Remove the screws, license light cover and license light cover packing. 2. Pull out the bulb without turning. Cover packing Troubleshooting Bulb Screws License light cover 3. Install a new bulb and parts in the reverse order of removal. 101 13 CB500F-32MGZA000.book 102 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Blown Fuse Blown Fuse (CB500F) Fuse box covers Before handling fuses, see “Inspecting and Replacing Fuses.” 2 P. 49 ❙ Fuse Box Fuses Troubleshooting 1. Remove the front seat. 2 P. 59 2. Remove the fuse box covers. 3. Pull the fuses out with the fuse puller in the tool kit one by one check for a blown fuse. Always replace a blown fuse with a spare of the same rating. 4. Install the fuse box cover. 5. Install the front seat. Spare fuses (CB500FA) Fuse box covers Spare fuses 102 13 CB500F-32MGZA000.book 103 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Electrical Trouble u Blown Fuse ❙ Main Fuse Main fuse Wire connector NOTICE If a fuse fails repeatedly, you likely have an electrical problem. Have your motorcycle inspected by your dealer. Starter magnetic switch Troubleshooting 3. Pull the main fuse out and check for a blown fuse. Always replace a blown fuse with a spare of the same rating. u Spare main fuse is provided in the starter magnetic switch. 4. Reinstall parts in the reverse order of removal. Spare main fuse 1. Remove the right side cover. 2 P. 60 2. Disconnect the wire connector of the starter magnetic switch. 103 13 CB500F-32MGZA000.book 104 ページ ２０１２年１１月２７日 Information Keys...........................................................P. 105 Instruments, Controls, & Other Features ..P. 106 Fuels Containing Alcohol.........................P. 108 Catalytic Converter ..................................P. 109 Caring for Your Motorcycle.....................P. 110 Storing Your Motorcycle .........................P. 113 Transporting Your Motorcycle ................P. 113 You & the Environment ...........................P. 114 Serial Numbers .........................................P. 115 火曜日 午後３時５７分 13 CB500F-32MGZA000.book 105 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Keys Keys Ignition key A metal key holder may cause damage to the area surrounding the ignition switch. Information The ignition key contains a special coded chip that is recognized by the immobilizer system (HISS) in order to start the engine. Handle the key carefully to prevent damaging the HISS components. ● Do not bend keys or subject them to undue stress. ● Avoid prolonged exposure to sunlight or high temperatures. ● Do not grind, drill or in any way alter their shape. ● Do not expose to strong magnetic objects. To make a duplicate key and register it with your HISS system, take the spare key, the key number plate, and the motorcycle to your dealer. If you lose all keys and the key number plate, the PGM-FI unit/ignition control module must be replaced by your dealer. To avoid this, keep a duplicate key. If you lose a key, make another duplicate key immediately. 105 13 CB500F-32MGZA000.book 106 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments, Controls, & Other Features Instruments, Controls, & Other Features Ignition Switch Information The headlight is always on when the ignition switch is on. Leaving the ignition switch on with the engine stopped will drain the battery. Do not turn the key while riding. Engine Stop Switch Do not use the engine stop switch except in an emergency. Doing so when riding will cause the engine to suddenly turn off, making riding unsafe. If you stop the engine using the engine stop switch, turn the ignition switch off. Failing to do so will drain the battery. Odometer The display locks 999999 when the read-out exceeds 999999. 106 Tripmeter The tripmeter A, B returns to 0.0 when the read-out exceeds 9999.9. HISS The Honda Ignition Security System (HISS) immobilizes the engine’s ignition system if an improperly-coded key is used to try and start the engine. When the ignition switch is turned off, the HISS immobilizer system is always alert, even if the HISS indicator is not flashing. If the ignition switch is turned on with the engine stop switch in the (Run) position, the HISS indicator turns on and goes off after a few seconds to indicate it is OK to start the engine. 2 HISS Indicator Does Not Turn OFF P. 85 The HISS indicator starts flashing every 2 seconds for 24 hours after the ignition switch is turned off. You can turn this feature on or off. 2 P. 26 13 CB500F-32MGZA000.book 107 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Instruments, Controls, & Other Features Morocco only EC Directive This immobilizer system complies with R & TTE (Radio and Telecommunications Terminal Equipment and the mutual recognition of their conformity) Directive. Document Bag The owner’s manual, registration, and insurance information can be stored in the plastic document bag located underside of the front seat. 2 P. 40 Information The declaration of conformity to R & TTE Directive is provided to the owner at the time of purchase. The declaration of conformity should be kept at a safe place. When the declaration of conformity is lost or is not provided, contact your dealer. Ignition Cut-off System South Africa only Singapore only A banking (lean angle) sensor automatically stops the engine and fuel pump if the motorcycle falls over. To reset the sensor, you must turn the ignition switch to OFF and back to the ON position before the engine can be restarted. 107 13 CB500F-32MGZA000.book 108 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Fuels Containing Alcohol Fuels Containing Alcohol Some conventional fuels blended with alcohol are available in some locales to help reduce emissions to meet clean air standards. If you plan to use blended fuel, check that it is unleaded and meets the minimum octane rating requirement. Information 108 The following fuel blends can be used in your motorcycle: ● Ethanol (ethyl alcohol) 10% by volume (max). ● Petrol containing ethanol may be marketed under the name Gasohol. ● Methanol (methyl alcohol) 5% by volume (max) that contain cosolvents and corrosion inhibitors to protect the fuel system. Never use a blend containing more than 5%. The use of petrol containing more than 10% ethanol (or more than 5% methanol) may: ● Damage the painting of the fuel tank. ● Damage the rubber tubes of the fuel line. ● Cause corrosion of the fuel tank. ● Cause poor drivability. NOTICE Use of blended fuels containing higher than approved percentages can damage metal, rubber, plastic parts of your fuel system. If you notice any undesirable operating symptoms or performance problems, try a different brand of petrol. 13 CB500F-32MGZA000.book 109 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Catalytic Converter Catalytic Converter A defective catalytic converter contributes to air pollution and can impair your engine’s performance. A replacement unit must be an original Honda part or equivalent. Information This motorcycle is equipped with a three-way catalytic converter. The catalytic converter contain precious metals that serve as catalysts in high temperature chemical reactions that convert hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) in the exhaust gasses into safe compounds. Follow these guidelines to protect your motorcycle’s catalytic converter. ● Always use unleaded petrol. Leaded petrol will damage the catalytic converter. ● Keep the engine in good running condition. ● Have your motorcycle serviced if your engine is misfiring, backfiring, stalling, or otherwise not running properly, stop riding and turn off the engine. 109 13 CB500F-32MGZA000.book 110 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Caring for Your Motorcycle Caring for Your Motorcycle Information Frequent cleaning and polishing is important to ensure the long life of your Honda. A clean motorcycle makes it easier to spot potential problems. In particular, seawater and salts used to prevent ice on roads promote the formation of corrosion. Always wash your motorcycle thoroughly after riding on coastal or treated roads. Washing Allow the engine, muffler, brakes, and other high-temperature parts to cool before washing. 1. Rinse your motorcycle thoroughly using a garden hose to remove loose dirt. 2. If necessary, use a sponge or a soft towel with mild cleaner to remove road grime. u Clean the headlight lens, panels, and other plastic components with extra care to avoid scratching them. Avoid directing 110 water into the air cleaner, muffler, and electrical parts. 3. Thoroughly rinse your motorcycle with plenty of clean water and dry with a soft, clean cloth. 4. After the motorcycle dries, lubricate any moving parts. u Make sure that no lubricant spills onto the brakes or tyres. Brake discs or pads contaminated with oil suffer greatly reduced braking effectiveness and can lead to a crash. 5. Lubricate the drive chain immediately after washing and drying the motorcycle. 6. Apply a coat of wax to prevent corrosion. u Avoid products that contain harsh detergents or chemical solvents. These can damage the metal, paint, and plastic on your motorcycle. Keep the wax clear of the tyres and brakes. u If your motorcycle has any matte painted parts, do not apply a coat of wax to the matte painted surface. 13 CB500F-32MGZA000.book 111 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Caring for Your Motorcycle ● Do not direct water near the headlight: Follow these guidelines when washing: ● Do not use high-pressure washers: u High-pressure water cleaners can damage moving parts and electrical parts, rendering them inoperable. ● Do not direct water at the muffler: u Water in the muffler can prevent starting and causes rust in the muffler. ● Dry the brakes: u Water adversely affects braking effectiveness. After washing, apply the brakes intermittently at low speed to help dry them. ● Do not direct water under the rear seat: u Water in the under seat compartment can damage your documents and other belongings. ● Do not direct water at the air cleaner: u Water in the air cleaner can prevent the engine from starting. u Any condensation inside the headlight should dissipate after a few minutes of running the engine. ● Do not use waxes containing compounds at the mat painted surface: u Using plenty of water, clean the mat painted surface with a soft cloth or sponge. Dry with a soft, clean cloth. u Use neutral detergent to clean mat painted surface. Aluminium Components Information ❙ Washing Precautions Aluminium will corrode from contact with dirt, mud, or road salt. Clean aluminium parts regularly and follow these guidelines to avoid scratches: ● Do not use stiff brushes, steel wool, or cleaners containing abrasives. ● Avoid riding over or scraping against curbs. continued 111 13 CB500F-32MGZA000.book 112 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Caring for Your Motorcycle Panels Information 112 Follow these guidelines to prevent scratches and blemishes: ● Wash gently using a soft sponge and plenty of water. ● To remove stubborn stains, use diluted detergent and rinse thoroughly with plenty of water. ● Avoid getting petrol, brake fluid, or detergents on the instruments, panels, or headlight. Exhaust Pipe and Muffler The exhaust pipe and muffler are stainless steel but may become stained by mud or dust. To remove mud or dust, use a wet sponge and a liquid kitchen abrasive, then rinse well with clean water. Dry with chamois or a soft towel. If necessary, remove heat stains by using a commercially available fine texture compound. Then rinse by the same manner as removing mud or dust. NOTICE Even though the exhaust is made of stainless steel, it can become stained. Remove all marks and blemishes as soon as they are noticed. 13 CB500F-32MGZA000.book 113 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Storing Your Motorcycle Storing Your Motorcycle Transporting Your Motorcycle If your motorcycle needs to be transported, it should be carried on a motorcycle trailer or a flatbed truck or trailer that has a loading ramp or lifting platform, and motorcycle tie-down straps. Never try to tow your motorcycle with a wheel or wheels on the ground. Information If you store your motorcycle outdoors, you should consider using a full-body motorcycle cover. If you won’t be riding for an extended period, follow these guidelines: ● Wash your motorcycle and wax all painted surfaces (except matte painted surfaces). Coat chrome pieces with rust-inhibiting oil. ● Lubricate the drive chain. 2 P. 52 ● Place your motorcycle on a maintenance stand and position a block so that both tyres are off the ground. ● After rain, remove the body cover and allow the motorcycle to dry. ● Remove the battery (2 P. 63) to prevent discharge. Charge the battery in a shaded, wellventilated area. u If you leave the battery in place, disconnect the negative - terminal to prevent discharge. After removing your motorcycle from storage, inspect all maintenance items required by the Maintenance Schedule. NOTICE Towing your motorcycle can cause serious damage to the transmission. 113 13 CB500F-32MGZA000.book 114 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 You & the Environment You & the Environment Owning and riding a motorcycle can be enjoyable, but you must do your part to protect the environment. Choose Sensible Cleaners Information Use a biodegradable detergent when you wash your motorcycle. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Recycle Wastes Put oil and other toxic wastes in approved containers and take them to a recycling centre. Call your local or state office of public works or environmental services to find a recycling centre in your area, and to get instructions on how to dispose of non-recyclable wastes. Do not place used engine oil in the trash, or pour it down a 114 drain or on the ground. Used oil, petrol, coolant, and cleaning solvents contain poisons that can hurt refuse workers and contaminate drinking water, lakes, rivers, and oceans. 13 CB500F-32MGZA000.book 115 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Serial Numbers Serial Numbers Frame number Information The frame and engine serial numbers uniquely identify your motorcycle and are required in order to register your motorcycle. They may also be required when ordering replacement parts. The frame number is stamped on the right side of the steering head. The engine number is stamped on the top of the crankcase. You should record these numbers and keep them in a safe place. Engine number 115 13 CB500F-32MGZA000.book 116 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Specifications Specifications ■ Main Components Type Overall length Overall width Overall height Wheelbase Minimum ground clearance Caster angle Trail Specifications Curb weight Maximum weight capacity*1 Maximum luggage weight Passenger capacity Minimum turning radius PC45 2,075 mm (81.7 in) 780 mm (30.7 in) 1,060 mm (41.7 in) 1,410 mm (55.5 in) 155 mm (6.1 in) 25º 30´ 103 mm (4.1 in) CB500F 190 kg (419 lb) CB500FA 192 kg (423 lb) 182 kg (401 lb) 11 kg (24 lb) Rider and 1 passenger 2.7 m (8.9 ft) *1 Including rider, passenger, all luggage, and accessories 116 Displacement 471 cm3 (28.7 cu-in) Bore × stroke 67.0 × 66.8 mm (2.64 × 2.63 in) Compression ratio 10.7:1 Unleaded petrol Fuel Recommended: 91 RON or higher Tank capacity 15.7 litres (4.15 US gal, 3.45 Imp gal) FTZ10S 12V-8.6Ah (10 HR) / 9.1Ah (20 HR) Battery YTZ10S 12V-8.6Ah (10 HR) / 9.1Ah (20 HR) 1st 3.285 2nd 2.105 3rd 1.600 Gear ratios 4th 1.300 5th 1.150 6th 1.043 Reduction ratios 2.029 / 2.733 (primary / final) 13 CB500F-32MGZA000.book 117 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Specifications ■ Service Data Front Rear Engine oil capacity Recommended brake fluid Cooling system capacity Recommended coolant Recommended drive chain lubricant Drive chain slack Standard drive chain After draining 2.5 litres (2.6 US qt, 2.2 Imp qt) After draining & engine oil filter change 2.7 litres (2.9 US qt, 2.4 Imp qt) After disassembly 3.2 litres (3.4 US qt, 2.8 Imp qt) Honda DOT 4 Brake Fluid 1.40 litres (1.48 US qt, 1.23 Imp qt) Pro Honda HP Coolant Drive chain lubricant designed specifically for O-ring chains 35 to 45 mm (1.4 to 1.8 in) DID 520V0 No. of links Engine sprocket Standard Rear wheel sprocket sizes sprocket Specifications 120/70ZR17M/C (58W) 160/60ZR17M/C (69W) Tyre type Radial, tubeless DUNLOP D222F Front METZELER ROADTEC Z8 INTERACT E Recommended Tyres DUNLOP D222 Rear METZELER ROADTEC Z8 INTERACT Front 250 kPa (2.50 kgf/cm2, 36 psi) Tyre air pressure Rear 290 kPa (2.90 kgf/cm2, 42 psi) Front 1.5 mm (0.06 in) Minimum tread depth Rear 2.0 mm (0.08 in) Spark plugs (standard) CPR8EA-9 (NGK) Spark plug gap 0.80 to 0.90 mm (0.031 to 0.035 in) Idle speed 1,200 ± 100 rpm Honda 4-stroke motorcycle oil API Service Classification SG or higher, excluding oils Recommended marked as “Energy Conserving” or “Resource engine oil Conserving,” SAE 10W-30, JASO T 903 standard MA Tyre size 112 15T 41T 117 13 CB500F-32MGZA000.book 118 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Specifications ■ Bulbs ■ Torque Specifications Headlight Brake/Tail light Front turn signal lights Rear turn signal lights Position light License plate light 12V-60/55W 12V-21/5W 12V-21W × 2 12V-21W × 2 12V-5W 12V-5W Engine oil drain bolt Oil filter Front wheel axle shaft Front wheel brake caliper mounting bolts Front wheel axle pinch bolt Rear wheel axle nut Drive chain adjusting lock nuts ■ Fuses Main fuse Other fuses Specifications 118 30A CB500F CB500FA 15A, 7.5A 30A, 15A, 7.5A 30 N·m (3.1 kgf·m, 22 lbf·ft) 26 N·m (2.7 kgf·m, 19 lbf·ft) 54 N·m (5.5 kgf·m, 40 lbf·ft) 30 N·m (3.1 kgf·m, 22 lbf·ft) 22 N·m (2.2 kgf·m, 16 lbf·ft) 88 N·m (9.0 kgf·m, 65 lbf·ft) 21 N·m (2.1 kgf·m, 15 lbf·ft) 13 CB500F-32MGZA000.book 119 ページ ２０１２年１１月２７日 火曜日 午後３時５７分 Index Index A ABS (Anti-lock Brake System) Indicator ............................................ 32, 88 Accessories................................................. 16 Anti-lock Brake System (ABS)................... 13 D Digital Clock Adjustment.................... 26, 27 Display Setting........................................... 26 Drive Chain ................................................ 73 E Electrical Trouble....................................... 97 Engine Number.................................................. 115 Oil ...................................................... 50, 64 Oil Filter.................................................... 66 Overheats................................................. 86 Starting .................................................... 36 Stop Switch ................................ 34, 36, 106 Stopping ................................................ 106 Index B Battery ................................................. 48, 63 Brakelight Switch...................................... 83 Brakes Fluid................................................... 51, 70 Pad Wear ................................................. 71 Braking ...................................................... 12 Bulb Brake/Tail Light ........................................ 99 Front Turn Signal.................................... 100 Headlight ................................................. 98 License Plate Light.................................. 101 Position Light ........................................... 99 Rear Turn Signal..................................... 100 C Caring for Your Motorcycle.................... 110 Catalytic Converter.................................. 109 Clutch System ............................................ 77 Colour label ............................................... 47 Coolant ................................................ 52, 68 Crankcase Breather ................................... 81 119 13 CB500F-32MGZA000.book 120 ページ ２０１２年１１月２７日 Environment ............................................ 114 Equipment Owner’s Manual............................... 40, 107 Tool Kit .............................................. 40, 57 Index F Flooded Engine ......................................... 36 Frame Number......................................... 115 Front Seat .................................................. 59 Fuel Consumption Meter ................................. 22 Gauge ...................................................... 21 Mileage Meter.......................................... 22 Recommended ......................................... 38 Remaining .......................................... 21, 25 Tank Capacity........................................... 38 Fuels Containing Alcohol........................ 108 Fuses................................................... 49, 102 G Gasohol .................................................... 108 120 火曜日 午後３時５７分 H Hazard Switch ............................................34 Headlight Aim............................................83 Headlight Assembly...................................61 Headlight Dimmer Switch .........................34 Helmet Holder ...........................................39 High Beam Indicator..................................33 High Coolant Temperature Indicator .............................................32, 86 HISS Indicator...........................26, 30, 33, 85 Horn Button ...............................................34 I Ignition Cut-off System Banking Sensor .......................................107 Side Stand ................................................72 Ignition key ..............................................105 Ignition Switch.....................................35, 36 Image Labels ................................................6 Indicators....................................................32 Instruments ................................................20 13 CB500F-32MGZA000.book 121 ページ ２０１２年１１月２７日 L Labels........................................................... 6 Load Limits ................................................ 17 Loading Guidelines ................................... 17 Low Oil Pressure Indicator.................. 32, 87 N Neutral Indicator....................................... 33 O Odometer .......................................... 22, 106 Oil Engine ............................................... 50, 64 Overheating .............................................. 86 午後３時５７分 P Parking....................................................... 14 Parts Location ............................................ 18 Passing light control switch ...................... 34 Petrol.................................................. 38, 108 PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) .... 32, 87 Protective Apparel .................................... 11 R Rear Seat.................................................... 58 Rear Suspension ........................................ 82 Recommended Coolant .................................................... 52 Fuel .......................................................... 38 Oil ............................................................ 50 Refuelling .................................................. 38 Removal Clips......................................................... 62 Front Seat................................................. 59 Headlight Assembly .................................. 61 Rear Seat.................................................. 58 Side Cover................................................ 60 Index M Maintenance Fundamentals .......................................... 46 Importance .............................................. 42 Safety ...................................................... 42 Schedule .................................................. 43 Maximum Weight Limit............................ 17 Modifications ............................................ 16 火曜日 121 13 CB500F-32MGZA000.book 122 ページ ２０１２年１１月２７日 Repair Kit ................................................... 90 Riding Precautions .................................... 12 Index 122 S Safety Precautions..................................... 11 Serial Numbers ........................................ 115 Shifting Gears ............................................ 37 Side Cover .................................................. 60 Side Stand .................................................. 72 Side Stand Ignition Cut-off System .......... 72 Specifications........................................... 116 Speedometer ............................................. 21 Start Button ......................................... 34, 36 Starting the Engine ................................... 36 Steering Lock ............................................. 35 Stopping Engine...................................... 106 Storage Equipment................................................ 39 Owner’s Manual............................... 40, 107 Tool Kit .................................................... 40 Storing Your Motorcycle......................... 113 Switches ..................................................... 34 火曜日 午後３時５７分 T Tachometer ................................................21 Throttle ......................................................80 Tool kit .......................................................57 Transporting Your Motorcycle................113 Tripmeter ...........................................22, 106 Troubleshooting ........................................84 Turn signal indicators ................................33 Tyres Air Pressure...............................................53 Puncture ...................................................90 Replacing............................................53, 90 W Warning Indicators On ..............................87 Washing Your Motorcycle.......................110 Weight Limit ..............................................17 Wheels Front removal ...........................................91 Rear removal.............................................94