14 CTX700-32MJF8000.book 1 ページ 2013年5月9日 木曜日 午後9時59分 This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when it is resold. This publication includes the latest production information available before printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. The vehicle pictured in this owner’s manual may not match your actual vehicle. © 2013 Honda Motor Co., Ltd. 14 CTX700-32MJF8000.book 2 ページ 2013年5月9日 木曜日 午後9時59分 Welcome Congratulations on your purchase of a new Honda motorcycle. Your selection of a Honda makes you part of a worldwide family of satisfied customers who appreciate Honda’s reputation for building quality into every product. To ensure your safety and riding pleasure: ● Read this owner’s manual carefully. ● Follow all recommendations and procedures contained in this manual. ● Pay close attention to safety messages contained in this manual and on the motorcycle. The following codes in this manual indicate each country. ● The illustrations here in are based on the CTX700A ED type. Country Codes ● Code CTX700A E ED KO U CTX700D E ED U Country UK European direct sales Korea Australia, New Zealand UK European direct sales Australia, New Zealand *The specifications may vary with each locale. 14 CTX700-32MJF8000.book 3 ページ 2013年5月9日 木曜日 午後9時59分 A Few Words About Safety Your safety, and the safety of others, is very important. Operating this motorcycle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on safety labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining a motorcycle. You must use your own good judgment. You will find important safety information in a variety of forms, including: ● Safety labels on the motorcycle ● Safety Messages preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION. These signal words mean: 3 DANGER You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 WARNING You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 CAUTION You CAN be HURT if you don’t follow instructions. Other important information is provided under the following titles: NOTICE Information to help you avoid damage to your motorcycle, other property, or the environment. 14 CTX700-32MJF8000.book 4 ページ 2013年5月9日 木曜日 午後9時59分 Contents Motorcycle Safety P. 2 Operation Guide P. 18 Maintenance P. 47 Troubleshooting P. 94 Information P. 115 Specifications P. 128 Index P. 131 14 CTX700-32MJF8000.book 2 ページ 2013年5月9日 木曜日 午後9時59分 Motorcycle Safety This section contains important information for safe riding of your motorcycle. Please read this section carefully. Safety Guidelines .........................................P. 3 Image Labels.................................................P. 6 Safety Precautions .....................................P. 11 Riding Precautions .....................................P. 12 Accessories & Modifications......................P. 16 Loading .......................................................P. 17 14 CTX700-32MJF8000.book 3 ページ 2013年5月9日 木曜日 午後9時59分 Safety Guidelines Safety Guidelines Always Wear a Helmet It’s a proven fact: helmets and protective apparel significantly reduce the number and severity of head and other injuries. So always wear an approved motorcycle helmet and protective apparel. 2 P. 11 Before Riding Take Time to Learn & Practice Even if you have ridden other motorcycles, practice riding in a safe area to become familiar with how this motorcycle works and handles, and to become accustomed to the motorcycle’s size and weight. Ride Defensively Always pay attention to other vehicles around you, and do not assume that other drivers see you. Be prepared to stop quickly or perform an evasive maneuver. Make sure that you are physically fit, mentally focused and free of alcohol and drugs. Check continued 3 Motorcycle Safety Follow these guidelines to enhance your safety: ● Perform all routine and regular inspections specified in this manual. ● Stop the engine and keep sparks and flame away before filling the fuel tank. ● Do not run the engine in enclosed or partly enclosed areas. Carbon monoxide in exhaust gases is toxic and can kill you. that you and your passenger are both wearing an approved motorcycle helmet and protective apparel. Instruct your passenger on holding onto the grab rails or your waist, leaning with you in turns, and keeping their feet on the footpegs, even when the motorcycle is stopped. 14 CTX700-32MJF8000.book 4 ページ 2013年5月9日 木曜日 午後9時59分 Safety Guidelines Make Yourself Easy to See Motorcycle Safety Make yourself more visible, especially at night, by wearing bright reflective clothing, positioning yourself so other drivers can see you, signaling before turning or changing lanes, and using your horn when necessary. Ride within Your Limits Never ride beyond your personal abilities or faster than conditions warrant. Fatigue and inattention can impair your ability to use good judgement and ride safely. Don’t Drink and Ride Alcohol and riding don’t mix. Even one alcoholic drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. Don’t drink and ride, and don’t let your friends drink and ride either. 4 Keep Your Honda in Safe Condition It’s important to keep your motorcycle properly maintained and in safe riding condition. Inspect your motorcycle before every ride and perform all recommended maintenance. Never exceed load limits (2 P. 17), and do not modify your motorcycle or install accessories that would make your motorcycle unsafe (2 P. 16). If You are Involved in a Crash Personal safety is your first priority. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. Call for emergency assistance if needed. Also follow applicable laws and regulations if another person or vehicle is involved in the crash. If you decide to continue riding, first evaluate the condition of your motorcycle. If the engine is still running, turn it off. Inspect for fluid leaks, 14 CTX700-32MJF8000.book 5 ページ 2013年5月9日 木曜日 午後9時59分 Safety Guidelines 3 WARNING Motorcycle Safety check the tightness of critical nuts and bolts, and check the handlebar, control levers, brakes, and wheels. Ride slowly and cautiously. Your motorcycle may have suffered damage that is not immediately apparent. Have your motorcycle thoroughly checked at a qualified service facility as soon as possible. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any areas or activities that expose you to carbon monoxide. Carbon Monoxide Hazard Exhaust contains poisonous carbon monoxide, a colourless, odorless gas. Breathing carbon monoxide can cause loss of consciousness and may lead to death. If you run the engine in confined or even partly enclosed area, the air you breathe could contain a dangerous amount of carbon monoxide. Never run your motorcycle inside a garage or other enclosure. 5 14 CTX700-32MJF8000.book 6 ページ 2013年5月9日 木曜日 午後9時59分 Image Labels Image Labels Motorcycle Safety Read instructions contained in Owner’s Manual carefully. Except KO type The following pages describe the label meanings. Some labels warn you of potential hazards that could cause serious injury. Others provide important safety information. Read this information carefully and don’t remove the labels. If a label comes off or becomes hard to read, contact your dealer for a replacement. There is a specific symbol on each label. The meanings of each symbol and label are as follows. 6 Read instructions contained in Shop Manual carefully. In the interest of safety, take the motorcycle to be serviced only by your dealer. DANGER (with RED background) You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. WARNING (with ORANGE background) You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. CAUTION (with YELLOW background) You CAN be HURT if you don’t follow instructions. 14 CTX700-32MJF8000.book 7 ページ 2013年5月9日 木曜日 午後9時59分 Image Labels continued 7 Motorcycle Safety BATTERY LABEL DANGER • Keep flame and spark away from the battery. Battery produce explosive gas that can cause explosion. • Wear the eye protection and rubber gloves when handling the battery, or you can get burned or lose your eyesight by the battery electrolyte. • Do not allow children and other people to touch a battery unless they understand proper handling and hazards of the battery very well. • Handle the battery electrolyte with extreme care as it contains dilute sulfuric acid. Contact with your skin or eyes can burn you or cause loss of your eyesight. • Read this manual carefully and understand it before handling the battery. Neglect of the instructions can cause personal injury and damage to the motorcycle. • Do not use a battery with the electrolyte at or below the lower level mark. It can explode causing serious injury. 14 CTX700-32MJF8000.book 8 ページ 2013年5月9日 木曜日 午後9時59分 Image Labels Motorcycle Safety RADIATOR CAP LABEL DANGER NEVER OPEN WHEN HOT. Hot coolant will scald you. Relief pressure valve begins to open at 108 kPa. ACCESSORIES AND LOADING WARNING LABEL WARNING ACCESSORIES AND LOADING • The safety stability and handling of this motorcycle may be affected by the addition of accessories and luggage. • Read carefully the instructions contained in user’s manual and installation guide before installing any accessory. • The total weight of accessories and luggage added to rider’s and passenger’s weight should not exceed 190 kg (419 lb), which is the maximum weight capacity. • The luggage weight must not exceed 15.5 kg (34 lb) under any circumstances. • The fitting of large fork-mounted or large handlebar mounted fairing is not recommended. 8 14 CTX700-32MJF8000.book 9 ページ 2013年5月9日 木曜日 午後9時59分 Image Labels TYRE INFORMATION LABEL Cold tyre pressure: [Driver only] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 250 kPa (2.50 kgf/cm2, 36 psi) [Driver and passenger] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 290 kPa (2.90 kgf/cm2, 42 psi) Tyre size: Front 120/70ZR17M/C (58W) Rear 160/60ZR17M/C (69W) Tyre brand: BRIDGESTONE METZELER Front BT023F G ROADTEC Z8 INTERACT E Rear BT023R G ROADTEC Z8 INTERACT continued 9 Motorcycle Safety REAR CUSHION LABEL GAS FILLED Do not open. Do not heat. 14 CTX700-32MJF8000.book 10 ページ 2013年5月9日 木曜日 午後9時59分 Image Labels Motorcycle Safety SAFETY REMINDER LABEL For your protection, always wear helmet, protective apparel. FUEL LABEL Unleaded petrol only DRIVE CHAIN LABEL Keep chain adjusted and lubricated. 25 to 35 mm (1.0 to 1.4 in) Freeplay CARGO LIMIT LABEL Do not exceed 0.5 kg (1.0 lb) 10 14 CTX700-32MJF8000.book 11 ページ 2013年5月9日 木曜日 午後9時59分 Safety Precautions Safety Precautions ● Face shield with unobstructed field of vision handlebar and feet on the footpegs. ● Keep passenger’s hands onto the grab rails or your waist, passenger’s feet on the footpegs while riding. ● Always consider the safety of your passenger, as well as other drivers and riders. Protective Apparel Make sure that you and any passenger are wearing an approved motorcycle helmet, eye protection, and high-visibility protective clothing. Ride defensively in response to weather and road conditions. ❙ Helmet Safety-standard certified, high-visibility, correct size for your head ● Must fit comfortably but securely, with the chin strap fastened 3 WARNING Not wearing a helmet increases the chance of serious injury or death in a crash. Motorcycle Safety or other approved eye protection ● Ride cautiously and keep your hands on the Make sure that you and any passenger always wear an approved helmet and protective apparel. ❙ Gloves Full-finger leather gloves with high abrasion resistance ❙ Boots or Riding Shoes Sturdy boots with non-slip soles and ankle protection ❙ Jacket and Trousers Protective, highly visible, long-sleeved jacket and durable trousers for riding (or a protective suit). 11 14 CTX700-32MJF8000.book 12 ページ 2013年5月9日 木曜日 午後9時59分 Riding Precautions Riding Precautions Motorcycle Safety 12 Running-in Period During the first 500 km (300 miles) of running, follow these guidelines to ensure your motorcycle’s future reliability and performance. ● Avoid full-throttle starts and rapid acceleration. ● Avoid hard braking and rapid down-shifts. ● Ride conservatively. Brakes Observe the following guidelines: ● Avoid excessively hard braking and sudden shifting to a lower gear. u Sudden braking can reduce the motorcycle’s stability. u Where possible, reduce speed before turning; otherwise you risk wheel slippage. ● Exercise caution on low traction surfaces. u The tyres slip more easily on such surfaces and braking distances are longer. ● Avoid continuous braking. u Repeated braking, such as when descending long, steep slopes can seriously overheat the brakes, reducing their effectiveness. Use engine braking with intermittent use of the brakes to reduce speed. 14 CTX700-32MJF8000.book 13 ページ 2013年5月9日 木曜日 午後9時59分 Riding Precautions ❙ Engine Braking This model is equipped with an Anti-lock Brake System (ABS) designed to help prevent the brakes from locking up during hard braking. ● ABS does not reduce braking distance. In certain circumstances, ABS may result in a longer stopping distance. ● ABS does not function at speeds below 10 km/h (6 mph). ● The brake lever and pedal may recoil slightly when applying the brakes. This is normal. ● Always use the recommended tyres to ensure correct ABS operation. Engine braking helps slow your motorcycle down when you release the throttle. For further slowing action, downshift to a lower gear. Use engine braking with intermittent use of the brakes to reduce speed when descending long, steep slopes. Motorcycle Safety ❙ Anti-lock Brake System (ABS) ❙ Wet or Rainy Conditions Road surfaces are slippery when wet, and wet brakes further reduce braking efficiency. Exercise extra caution when braking in wet conditions. If the brakes get wet, apply the brakes while riding at low speed to help them dry. continued 13 14 CTX700-32MJF8000.book 14 ページ 2013年5月9日 木曜日 午後9時59分 Riding Precautions Parking Motorcycle Safety 14 ● Park on a firm, level paved surface. ● If you must park on a slight incline or loose surface, park so that the motorcycle cannot move or fall over. ● Make sure that high-temperature parts cannot come into contact with flammable materials. ● Do not touch the engine, muffler, brakes and other high-temperature parts until they cool down. ● To reduce the likelihood of theft, always lock the handlebar and remove the key when leaving the motorcycle unattended. Use of an anti-theft device is also recommended. ❙ Parking with the Side Stand 1. Stop the engine. 2. Push the side stand down. 3. Slowly lean the motorcycle to the left until its weight rests on the side stand. 4. Turn the handlebar fully to the left. u Turning the handlebar to the right reduces stability and may cause the motorcycle to fall. 5. Turn the ignition switch to the LOCK position and remove the key. 2 P. 31 14 CTX700-32MJF8000.book 15 ページ 2013年5月9日 木曜日 午後9時59分 Riding Precautions Refuelling and Fuel Guidelines Motorcycle Safety Follow these guidelines to protect the engine and catalytic converter: ● Use only unleaded petrol. ● Use recommended octane number. Using lower octane petrol will result in decreased engine performance. ● Do not use fuels containing a high concentration of alcohol. 2 P. 120 ● Do not use stale or contaminated petrol or an oil/petrol mixture. ● Avoid getting dirt or water in the fuel tank. 15 14 CTX700-32MJF8000.book 16 ページ 2013年5月9日 木曜日 午後9時59分 Accessories & Modifications Motorcycle Safety 16 Accessories & Modifications We strongly advise that you do not add any accessories that were not specifically designed for your motorcycle by Honda or make modifications to your motorcycle from its original design. Doing so can make it unsafe. Modifying your motorcycle may also void your warranty and make your motorcycle illegal to operate on public roads and highways. Before deciding to install accessories on your motorcycle be certain the modification is safe and legal. 3 WARNING Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding accessories and modifications. Do not pull a trailer with, or attach a sidecar to, your motorcycle. Your motorcycle was not designed for these attachments, and their use can seriously impair your motorcycle’s handling. 14 CTX700-32MJF8000.book 17 ページ 2013年5月9日 木曜日 午後9時59分 Loading Loading motorcycle’s handling, braking and stability. Always ride at a safe speed for the load you are carrying. ● Avoid carrying an excessive load and keep within specified load limits. 2 Maximum weight capacity / Maximum luggage weight P. 128 ● Tie all luggage securely, evenly balanced and close to the centre of the motorcycle. ● Do not place objects near the lights or the muffler. Overloading or improper loading can cause a crash and you can be seriously hurt or killed. Follow all load limits and other loading guidelines in this manual. Motorcycle Safety ● Carrying extra weight affects your 3 WARNING 17 14 CTX700-32MJF8000.book 18 ページ 2013年5月9日 木曜日 午後9時59分 Parts Location CTX700A Operation Guide Battery (P69) Main fuse (P114) Throttle grip (P90) Front brake lever Front brake fluid reservoir (P78) Engine oil fill cap/dipstick (P70) Right under cowl lid (P65) Brake light switch (P93) Centre lower cowl (P66) Engine oil filter (P73) Rear brake fluid reservoir (P78) Coolant reserve tank (P76) Rear brake pedal 18 14 CTX700-32MJF8000.book 19 ページ 2013年5月9日 木曜日 午後9時59分 Clutch lever (P87) Operation Guide Shelter pocket (P44) Fuel fill cap (P42) Fuse box (P113) Seat (P64) Drive chain (P82) Engine oil drain bolt (P72) Side stand (P81) Crankcase breather (P91) Shift lever (P36) continued 19 14 CTX700-32MJF8000.book 20 ページ 2013年5月9日 木曜日 午後9時59分 Parts Location (Continued) CTX700D Operation Guide Battery (P69) Main fuse (P114) Throttle grip (P90) Front brake lever Front brake fluid reservoir (P78) Engine oil fill cap/dipstick (P71) Right under cowl (P67) Right under cowl lid (P65) Brake light switch (P93) Centre lower cowl (P66) Engine oil filter (P73) Rear brake fluid reservoir (P78) Coolant reserve tank (P76) Rear brake pedal Clutch oil filter (P74) 20 14 CTX700-32MJF8000.book 21 ページ 2013年5月9日 木曜日 午後9時59分 Fuse box (P113) Seat (P64) Operation Guide Parking brake lever (P32) Shelter pocket (P44) Fuel fill cap (P42) Drive chain (P82) Engine oil drain bolt (P72) Side stand (P81) Crankcase breather (P91) 21 14 CTX700-32MJF8000.book 22 ページ 2013年5月9日 木曜日 午後9時59分 Instruments Operation Guide A button B button Display Check When the ignition switch is turned on, all the mode and digital segments will show. If any part of these displays does not come on when it should, have your dealer check for problems. 22 14 CTX700-32MJF8000.book 23 ページ 2013年5月9日 木曜日 午後9時59分 CTX700A Tachometer NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. Speedometer Odometer [TOTAL] & Tripmeter [TRIP A/B] A button switches between odometer & tripmeters at the ordinary display. • Odometer: Total distance ridden. • Tripmeter: Distance ridden since tripmeter was reset (press and hold the B button to reset to 0.0 km/mile). Operation Guide Clock (12-hour display) To set the clock: (P27) Tachometer red zone (excessive engine rpm range) Fuel gauge Remaining fuel when only 1st (E) segment starts flashing: approximately 3.7 litres (0.98 US gal, 0.81 Imp gal) If the fuel gauge indicator repeat flashing or turned off: (P100) continued 23 14 CTX700-32MJF8000.book 24 ページ 2013年5月9日 木曜日 午後9時59分 Instruments (Continued) CTX700D Operation Guide Clock (12-hour display) To set the clock: (P27) NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. Speedometer Odometer [TOTAL] & Tripmeter [TRIP A/B] A button switches between odometer & tripmeters at the ordinary display. • Odometer: Total distance ridden. • Tripmeter: Distance ridden since tripmeter was reset (press and hold the B button to reset to 0.0 km/mile). 24 Tachometer Tachometer red zone (excessive engine rpm range) Fuel gauge Remaining fuel when only 1st (E) segment starts flashing: approximately 3.7 litres (0.98 US gal, 0.81 Imp gal) If the fuel gauge indicator repeat flashing or turned off: (P100) 14 CTX700-32MJF8000.book 25 ページ 2013年5月9日 木曜日 午後9時59分 u “-” appears for a few seconds and then goes off when the engine starts. u “-” flashes when the engine stop switch position is changed from (Run) to with the ignition switch on. u “-” flashes when the ignition switch is turned on with the engine stop switch Operation Guide D indicator Comes on when the D mode is selected in the AT MODE. (P40) S indicator Comes on when the S mode is selected in the AT MODE. (P40) Gear position indicator The gear position is shown in the gear position indicator when the D, S mode or MT MODE are selected. (Off) position (Off) position. The indicator may flash if: u The front wheel leaves the ground. u You turn the wheel while the motorcycle is upright on the stand. This is normal. To operate the system again, turn the ignition switch off, then on again. If the “-” indicator is blinking in the gear position window while riding: (P99) continued 25 14 CTX700-32MJF8000.book 26 ページ 2013年5月9日 木曜日 午後9時59分 Instruments (Continued) Operation Guide Display Setting You can adjust the three settings. • Backlight brightness adjustment • Clock setting • E type only Changing of speed and mileage unit Ordinary display Display setting Backlight brightness adjustment Clock setting In addition, to return to the ordinary display at display setting. • The button is not pressed for about 30 seconds • Turn the ignition switch off and then on Each setting will be cancelled if the A button is not pressed. 1 Backlight brightness adjustment: You can adjust the brightness to one of three levels. !a Turn the ignition switch to ON. !b Press and hold the A button and B button until the minute digit displays the brightness level. !c Press the B button. The brightness is switched. Changing of speed and mileage unit Press and hold the A button and B button Except E type Press the A button E type only Press the A button 26 !d Press the A button. The backlight is set, and then the display moves to the clock setting. 14 CTX700-32MJF8000.book 27 ページ 2013年5月9日 2 To set the clock: !b Press the B button until the desired hour and AM/PM are displayed. u Press and hold to advance the hour fast. !c Press the A button. The minute digits start flashing. !d Press the B button until the desired minute is displayed. u Press and hold to advance the minute fast. 午後9時59分 !e Except E type Press the A button. The clock is set, and then the display returns to the backlight brightness adjustment. E type only Press the A button. The clock is set, and then the display moves to the changing of the speed and mileage unit. Operation Guide !a After backlight brightness adjustment, the hour digits start flashing. 木曜日 3 E type only Changing the speed and mileage unit: !a After clock setting, the speed and mileage unit start flashing. !b Press the B button to select either “km/h” and “km” or “mph” and “mile”. !c Press the A button. The speed and mileage unit is set, and then the display returns to the backlight brightness adjustment. 27 14 CTX700-32MJF8000.book 28 ページ 2013年5月9日 木曜日 午後9時59分 Indicators Operation Guide Low oil pressure indicator Comes on when the ignition switch is turned on. Goes off when the engine starts. If it comes on while engine is running: (P97) ABS (Anti-lock Brake System) indicator Comes on when the ignition switch is turned on. Goes off when your speed reaches approximately 10 km/h (6 mph). If it comes on while riding: (P98) High coolant temperature indicator If it comes on while riding: (P96) PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) Comes on briefly when the ignition switch is turned on with the engine stop switch in the (Run) position. Comes on when the ignition switch is turned on with the engine stop switch in the (Off) position. If it comes on while engine is running: (P97) 28 14 CTX700-32MJF8000.book 29 ページ 2013年5月9日 木曜日 午後9時59分 Parking brake indicator CTX700D only HISS indicator (P117) • Comes on briefly when the ignition switch is turned on with the engine stop switch in the (Run) position. Goes off if the ignition key has the correct coding. • Flashes every 2 seconds for 24 hours when the ignition switch is turned off. Operation Guide Lights as a reminder that you have not released the parking brake lever. Right turn signal indicator High beam indicator Left turn signal indicator Neutral indicator Comes on when the transmission is in Neutral. 29 14 CTX700-32MJF8000.book 30 ページ 2013年5月9日 木曜日 午後9時59分 Switches CTX700A Operation Guide Engine stop switch Should normally remain in the (Run) position. u In an emergency, switch to the (Off) position to stop the engine. Start button Horn button Turn signal switch u Pressing the switch turns the turn signal off. Headlight dimmer/Passing light control switch • : High beam • : Low beam • : Flashes the high beam headlight. 30 Hazard switch Switchable when the ignition switch is on. Can be turned to off regardless of the ignition switch position. u The signals continue flashing with the ignition switch is OFF or LOCK position after the hazard switch is on. 14 CTX700-32MJF8000.book 31 ページ 2013年5月9日 木曜日 午後9時59分 ON u Key can be removed when in the OFF or LOCK position. Turns electrical system on for starting/riding. Operation Guide Ignition Switch Switches the electrical system on/off, locks the steering. OFF Turns engine off. LOCK Locks steering. Steering Lock ❙ Locking Lock the steering when parking to help prevent theft. !a Turn the handlebar all the way to the left. A U-shaped wheel lock or similar device is also recommended. !b Push !a !b Push the key down, and turn the ignition switch to the LOCK position. u Jiggle the handlebar if the lock is difficult to engage. !c Remove the key. ❙ Unlocking Turn Insert the key, push it in, and turn the ignition switch to the OFF position. Ignition key continued 31 14 CTX700-32MJF8000.book 32 ページ 2013年5月9日 木曜日 午後9時59分 Switches (Continued) CTX700D Operation Guide Parking brake lever and Release button Be sure the parking brake is applied while parking and warming up the engine. u Make sure the parking brake lever is released before riding. Shift up switch (+) To apply the parking brake lock Pull the parking brake lever back to lock the rear wheel. u Be sure the release button pops out and parking brake lever is not released. u The parking brake lock will not function if the parking brake is not adjusted properly. (P80) To release the parking brake lock Release the parking brake lever by lightly pulling in the lever (!a) and pressing the release button (!b). u Before riding, check that the parking brake indicator is turned off and make sure that the parking brake is fully released so there is no drag on the rear wheel. 32 Hazard switch (P30) To shift up the gear. (P41) Headlight dimmer/ Passing light control switch • : High beam • : Low beam • : Flashes the high beam headlight. !a Shift down switch (-) To shift down the gear. (P41) Turn signal switch !b u Pressing the switch turns the turn signal off. 14 CTX700-32MJF8000.book 33 ページ 2013年5月9日 木曜日 午後9時59分 u Key can be removed when in the OFF or LOCK position. Steering Lock: (P31) AT/MT switch To shift between the AT MODE and MT MODE. Horn button Operation Guide Ignition Switch Switches the electrical system on/off, locks the steering. (P40) N-D switch To shift between Neutral and AT MODE. (P40) Engine stop switch Should normally remain in the (Run) position. Start button u In an emergency, switch to the (Off) position to stop the engine. 33 14 CTX700-32MJF8000.book 34 ページ 2013年5月9日 木曜日 午後9時59分 Starting the Engine CTX700A Operation Guide Start your engine using the following procedure, regardless of whether the engine is cold or warm. !c !a !d !b NOTICE • If the engine does not start within 5 seconds, turn the ignition off and wait 10 seconds before trying to start the engine again for recovery of battery voltage. • Extended fast idling and revving the engine can damage the engine, and the exhaust system. • Snapping the throttle or fast idling for more than about 5 minutes may cause exhaust pipe discolouration. 34 !a Make sure the engine stop switch is in the (Run) position. !b Turn the ignition switch to the ON position. !c Shift the transmission to Neutral ( N indicator comes on). Alternatively, pull in the clutch lever to start your motorcycle with the transmission in gear so long as the side stand is raised. !d Press the start button with the throttle completely closed. If the engine does not start: !a Open the throttle fully and press the start button for 5 seconds. !b Repeat the normal starting procedure. !c If the engine starts, open the throttle slightly if idling is unstable. !d If the engine does not start, wait 10 seconds before trying steps !a & !b again. ❙ If Engine Will Not Start (P95) 14 CTX700-32MJF8000.book 35 ページ 2013年5月9日 CTX700D !e !c !a 午後9時59分 !a Make sure the engine stop switch is in the (Run) position. !b Turn the ignition switch to the ON position. !c Check the transmission in Neutral ( N indicator comes on). !d Press the start button with the throttle completely closed. !e Make sure the parking brake lever is released before riding. Operation Guide Start your engine using the following procedure, regardless of whether the engine is cold or warm. 木曜日 ❙ If Engine Does Not Start (P34) !d !b NOTICE • If the engine does not start within 5 seconds, turn the ignition off and wait 10 seconds before trying to start the engine again for recovery of battery voltage. • Extended fast idling and revving the engine can damage the engine, and the exhaust system. • Snapping the throttle or fast idling for more than about 5 minutes may cause exhaust pipe discolouration. When you stop the engine !a To stop the engine, put the transmission in to Neutral ( N indicator comes on). u If you turn the ignition switch to the OFF position when the motorcycle in gear, the engine will shut off with the clutch disengaged. !b Turn the ignition switch off. !c Pull the parking brake lever when you park the motorcycle. 35 14 CTX700-32MJF8000.book 36 ページ 2013年5月9日 木曜日 午後9時59分 Shifting Gears CTX700A CTX700D Operation Guide Your motorcycle transmission has six forward gears in a one-down, five-up shift pattern. 2 3 4 5 6 N 1 If you put the motorcycle in gear with the side stand down, the engine will shut off. 36 CTX700D is equipped with an automatically controlled 6-speed transmission. It can be shifted automatically (by AT MODE) or manually (by MT MODE). 14 CTX700-32MJF8000.book 37 ページ 2013年5月9日 木曜日 午後9時59分 Dual Clutch Transmission N-D switch AT/MT switch AT MT MODE MODE Operation Guide In order to respond to rider demands in a broad range of situations, the transmission is equipped with three operating modes, AT MODE (including D mode for regular operation and S mode for sporty riding); and MT MODE (MT mode for a 6-speed manual operation), which delivers the same shift feel as a manual transmission. u Always use the recommended tyres and sprockets to ensure correct the Dual Clutch Transmission operation. The Dual Clutch Transmission system runs a self check immediately after starting the engine. “-” appears in the gear position indicator window for a few seconds, then goes out. While “-” appears, you cannot shift into gear. continued 37 14 CTX700-32MJF8000.book 38 ページ 2013年5月9日 木曜日 午後9時59分 Shifting Gears (Continued) Operation Guide 38 Neutral (N): Neutral is selected automatically when you turn the ignition switch to ON. u You may hear (click) noises when the transmission shifts to Neutral (N). This is normal. If neutral is not selected when you turn the ignition switch to ON: u Turn the ignition off and on again. u If neutral is still not selected after turning the ignition off then on again. (P99) When you can change between N and D u Motorcycle is stopped and the engine is idling. u Throttle is completely closed. It is not possible to change from Neutral to D mode while the throttle is applied. u You cannot change between N and D mode while the wheels are rotating. u Side stand is raised. NOTICE • To prevent clutch damage, do not use the throttle to keep the motorcycle stopped uphill. 14 CTX700-32MJF8000.book 39 ページ 2013年5月9日 午後9時59分 MT MODE: MT MODE (6-speed manual operation) You can choose between 6 gears in this mode. Operation Guide AT MODE: In this mode the gears are shifted automatically according to your riding conditions. And also using the shift up switch (+) or shift down switch (-), you can temporarily shift up or down. These switches are convenient when you want to temporarily down-shift in front of a curve, etc. (P41) You can choose between two modes within AT MODE: D mode and S mode. D mode (AT): This is the standard mode when AT MODE is selected. Select D mode for regular operation and efficient fuel economy. S mode (AT): Select this mode while riding in AT MODE when you need more power, such as when overtaking, climbing hills, or pulling away. 木曜日 continued 39 14 CTX700-32MJF8000.book 40 ページ 2013年5月9日 木曜日 午後9時59分 Shifting Gears (Continued) Changing between Neutral and AT/MT Operation Guide 40 Changing from Neutral (N) to AT MODE Press the D/S side of the N-D switch (!a). The D mode indicator comes on, ”1” is shown in the gear position indicator and first gear is selected. Changing from AT or MT MODE to Neutral Press N on the N-D switch (!b). Changing between D mode and S mode while in AT MODE Press the D/S side of the N-D switch. The S or D mode indicator comes on (!c, !d). Changing between AT MODE and MT MODE Press the AT/MT switch (!e). The S or D indicator goes out while MT MODE is selected (!f). N-D switch !e AT/MT !a switch !b !c !d !f 14 CTX700-32MJF8000.book 41 ページ 2013年5月9日 u If the MT MODE is selected, the transmission does not shift up automatically. Do not allow the engine revs to go into the red zone. u The transmission automatically shifts down when you slow down, even in MT MODE. u You will start from 1st gear even if MT MODE is selected. 午後9時59分 Gear shift operation Shifting Up: Press the shift up switch (+) (!g). Shifting Down: Press the shift down switch (-) (!h). You cannot continue shifting gears by keeping the shift switch pressed. To continue shifting gears release the switch and press it again. Operation Guide Riding in MT MODE Shift up and down with the + and - switch. The selected gear is shown on the gear position indicator. 木曜日 !g !h Shift Limit You cannot downshift if the engine will exceed the rev limit. 41 14 CTX700-32MJF8000.book 42 ページ 2013年5月9日 木曜日 午後9時59分 Refuelling Shelter lid Operation Guide Fuel type: Unleaded petrol only Fuel octane number: Your motorcycle is designed to use Research Octane Number (RON) 91 or higher. Tank capacity: 12.4 litres (3.28 US gal, 2.73 Imp gal) Refueling and Fuel Guideline (P15) ❙ Opening the Fuel Fill Cap Ignition key Fuel filler opening Filler neck plate Fuel level (max) Fuel fill cap 42 !a Open the shelter lid. !b Insert the ignition key, and turn it clockwise to remove the cap. 14 CTX700-32MJF8000.book 43 ページ 2013年5月9日 Closing the Fuel Fill Cap !b Push the fuel fill cap into the filler neck until it snaps closed and locks. !c Remove the key. u The key cannot be removed if the cap is not locked. !d Close the shelter lid. 午後9時59分 3 WARNING Petrol is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine, and keep heat, sparks, and flame away. • Handle fuel only outdoors. • Wipe up spills immediately. Operation Guide !a After refueling, align the fuel fill cap latch with the slot in the filler neck. 木曜日 Do not fill with fuel above the plate. 43 14 CTX700-32MJF8000.book 44 ページ 2013年5月9日 木曜日 午後9時59分 Storage Equipment Shelter Pocket Opening Pocket lid Operation Guide !b Pull up the rear of the pocket lid. Closing !a Push down the rear of the pocket lid until it locks in place. u Make sure that the tab is locked securely in position by pulling up lightly on the rear of the pocket lid. u The lock automatically locks when closed. Shelter pocket 44 !a Open the shelter lid. (P42) !b Never exceed the maximum weight limit. Maximum Weight: 0.5 kg (1.0 lb) u Do not store any items that are flammable or susceptible to heat damage. 14 CTX700-32MJF8000.book 45 ページ 2013年5月9日 木曜日 午後9時59分 Document Bag The tool kit is located under the seat. There is also space to store a U-shaped lock. The document bag is located underside of the seat. Rubber strap Document bag Tool kit Rubber strap U-shaped lock u Some U-shaped locks may not fit in the compartment due to their size or design. Operation Guide Tool Kit/U-shaped Lock Seat ❙ Removing the seat (P64) ❙ Removing the seat (P64) continued 45 14 CTX700-32MJF8000.book 46 ページ 2013年5月9日 木曜日 午後9時59分 Storage Equipment (Continued) Operation Guide Helmet holder u Use the helmet holder only when parked. The helmet holder is located under the seat. A helmet set wire is in the tool kit. ❙ Removing the seat (P64) Helmet set wire Helmet D-ring Helmet holder 3 WARNING Riding with a helmet attached to the holder can interfere with the rear wheel or suspension and could cause a crash in which you can be seriously hurt or killed. Use the helmet holder only while parked. Do not ride with a helmet secured by the holder. Helmet set wire 46 14 CTX700-32MJF8000.book 47 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully before attempting any maintenance. Refer to “Specifications” for service data. Importance of Maintenance ..................... P. 48 Maintenance Schedule .............................. P. 49 Maintenance Fundamentals ..................... P. 52 Tool kit ....................................................... P. 63 Removing & Installing Body Components ..P. 64 Seat .......................................................... P. 64 Right Under Cowl Lid................................ P. 65 Centre Lower Cowl................................... P. 66 Right Under Cowl ..................................... P. 67 Clip........................................................... P. 68 Battery...................................................... P. 69 Engine Oil................................................... P. 70 Coolant .......................................................P. 76 Brakes .........................................................P. 78 Side Stand...................................................P. 81 Drive Chain .................................................P. 82 Clutch ..........................................................P. 87 Throttle .......................................................P. 90 Crankcase Breather ....................................P. 91 Other Adjustments ....................................P. 92 Headlight Aim ...........................................P. 92 Brake Light Switch.....................................P. 93 14 CTX700-32MJF8000.book 48 ページ 2013年5月9日 木曜日 午後9時59分 Importance of Maintenance Importance of Maintenance Maintenance Keeping your motorcycle well-maintained is absolutely essential to your safety and to protect your investment, obtain maximum performance, avoid breakdowns, and reduce air pollution. Maintenance is the owner’s responsibility. Be sure to inspect your motorcycle before each ride, perform the periodic checks specified in the Maintenance Schedule. 2 P. 49 3 WARNING Improperly maintaining your motorcycle or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual. 48 Maintenance Safety Always read the maintenance instructions before you begin each task, and make sure that you have the tools, parts, and skills required. We cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Follow these guidelines when performing maintenance. ● Stop the engine and remove the key. ● Park your motorcycle on a firm, level surface using the side stand or a maintenance stand to provide support. ● Allow the engine, muffler, brakes, and other high-temperature parts to cool before servicing as you can get burned. ● Run the engine only when instructed, and do so in a well-ventilated area. 14 CTX700-32MJF8000.book 49 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Schedule The maintenance schedule specifies the maintenance requirements necessary to ensure safe, dependable performance, and proper emission control. Honda recommends that your dealer should road test your motorcycle after each periodic maintenance is carried out. Maintenance Maintenance work should be performed in accordance with Honda’s standards and specifications by properly trained and equipped technicians. Your dealer meets all of these requirements. Keep an accurate record of maintenance to help ensure that your motorcycle is properly maintained. Make sure that whomever performs the maintenance completes this record. All scheduled maintenance is considered a normal owner operating cost and will be charged for by your dealer. Retain all receipts. If you sell the motorcycle, these receipts should be transferred with the motorcycle to the new owner. continued 49 14 CTX700-32MJF8000.book 50 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Schedule Items Pre-ride Check 2 P. 52 × 1,000 km × 1,000 mi 1 0.6 Fuel Line I Maintenance Fuel Level I Throttle Operation I I 36 24 48 32 I I Annual Regular Refer to Check Replace page – I 42 I Air Cleaner *2 I I R I 90 I – R Crankcase Breather *3 91 Spark Plug I Valve Clearance Engine Oil I Engine Oil Filter Clutch Oil Filter CTX700D Engine Idle Speed Radiator Coolant *4 I I Maintenance Level : Intermediate. We recommend service by your dealer, unless you have the necessary tools and are mechanically skilled. Procedures are provided in an official Honda Shop Manual. : Technical. In the interest of safety, have your motorcycle serviced by your dealer. – R – I I I I R R R R R R 70 R R R R R R 73 R I Cooling System Drive Chain 50 Frequency *1 12 24 8 16 R 74 R I I I I I I I I I I I I I I I Every 1,000 km (600 mi): I – 3 Years Maintenance Legend I : Inspect (clean, adjust, lubricate, or replace if necessary) : Lubricate R : Replace : Clean 76 – 82 14 CTX700-32MJF8000.book 51 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Schedule Items Pre-ride Check 2 P. 52 × 1,000 km × 1,000 mi 1 0.6 Drive Chain Slider I Brake Pads Wear I Brake System I Brake light Switch Brake Lock Operation CTX700D I Headlight Aim Lights/Horn I Engine Stop Switch I Clutch System I Side Stand I 36 24 48 32 Annual Regular Refer to Check Replace page 86 I I I I I I I I I I I I I I 79 I I I I I 52 I I I I I 93 I I I I I I I I 2 Years 78 80 I 92 – – I I I I I 87 CTX700A I I I I I 81 I I I I I – I I I I I – I I I I I 59 Steering Head Bearings I I I Notes: *1 : At higher odometer readings, repeat at the frequency interval established here. *2 : Service more frequently when riding in unusually wet or dusty areas. *3 : Service more frequently when riding in rain or at full throttle. *4 : Replacement requires mechanical skill. I I I – I Suspension Nuts, Bolts, Fasteners Wheels/Tyres I I Maintenance Brake Fluid *4 Frequency *1 12 24 8 16 51 14 CTX700-32MJF8000.book 52 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals Pre-ride Inspection Maintenance 52 To ensure safety, it is your responsibility to perform a pre-ride inspection and make sure that any problem you find is corrected. A preride inspection is a must, not only for safety, but because having a breakdown, or even a flat tyre, can be a major inconvenience. Check the following items before you ride motorcycle: ● Fuel level − Fill fuel tank when necessary. 2 P. 42 ● Throttle − Check for smooth opening and full closing in all steering positions. 2 P. 90 ● Engine oil level − Add engine oil if necessary. Check for leaks. 2 P. 70 ● Coolant level − Add coolant if required. Check for leaks. 2 P. 76 Drive chain − Check condition and slack, adjust and lubricate if necessary. 2 P. 82 ● Brakes − Check operation; Front and Rear: check brake fluid level and pads wear. 2 P. 78, 79 ● Lights and horn − Check that lights, indicators and horn function properly. ● Engine stop switch − Check for proper function. ● Side stand ignition cut-off system − Check for proper function. 2 P. 81 ● Wheels and tyres − Check condition, air pressure and adjust if necessary. 2 P. 59 ● CTX700A only ● Clutch − Check operation; Adjust freeplay if necessary. 2 P. 87 14 CTX700-32MJF8000.book 53 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals Replacing Parts Colour label Always use Honda Genuine Parts or their equivalents to ensure reliability and safety. Maintenance When ordering coloured components, specify the model name, colour, and code mentioned on the colour label. The colour label is attached to the frame under the seat. 2 P. 64 3 WARNING Installing non-Honda parts may make your motorcycle unsafe and cause a crash in which you can be seriously hurt or killed. Always use Honda Genuine Parts or equivalents that have been designed and approved for your motorcycle. 53 14 CTX700-32MJF8000.book 54 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals Battery Maintenance Your motorcycle has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water. Clean the battery terminals if they become dirty or corroded. Do not remove the battery cap seals. There is no need to remove the cap when charging. NOTICE Your battery is a maintenance-free type and can be permanently damaged if the cap strip is removed. This symbol on the battery means that this product must not be treated as household waste. NOTICE An improperly disposed of battery can be harmful to the environment and human health. Always confirm local regulations for battery disposal. 54 3 WARNING The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled mechanic do the battery servicing. ❙ Cleaning the Battery Terminals 1. Remove the battery. 2 P. 69 2. If the terminals are starting to corrode and are coated with a white substance, wash with warm water and wipe clean. 14 CTX700-32MJF8000.book 55 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals 3. If the terminals are heavily corroded, clean and polish the terminals with a wire brush or sandpaper. Wear safety glasses. Fuses ❙ Inspecting and Replacing Fuses 4. After cleaning, reinstall the battery. The battery has a limited life span. Consult your dealer about when you should replace the battery. Always replace the battery with another maintenance-free battery of the same type. NOTICE Installing non-Honda electrical accessories can overload the electrical system, discharging the battery and possibly damaging the system. Turn off the ignition switch to remove and inspect fuses. If a fuse is blown, replace with a fuse of the same rating. For fuse ratings, see “Specifications.” 2 P. 130 Maintenance Fuses protect the electrical circuits on your motorcycle. If something electrical on your motorcycle stops working, check for and replace any blown fuses. 2 P. 113 Blown fuse NOTICE Replacing a fuse with one that has a higher rating greatly increases the chance of damage to the electrical system. continued 55 14 CTX700-32MJF8000.book 56 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals If a fuse fails repeatedly, you likely have an electrical fault. Have your motorcycle inspected by your dealer. *1. Engine Oil Maintenance Engine oil consumption and oil quality deteriorates according to riding conditions and time elapsed. Check the engine oil level regularly, and add the recommended engine oil if necessary. Dirty oil or old oil should be changed as soon as possible. ❙ Selecting the Engine Oil For recommended engine oil, see “Specifications.” 2 P. 129 If you use non-Honda engine oil, check the label to make sure that the oil satisfies all of the following standards: ● JASO T 903 standard*1: MA ● SAE standard*2: 10W-30 ● API classification*3: SG or higher 56 The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines. There are two classes: MA and MB. For example, the following label shows the MA classification. Oil code Oil classification *2. *3. The SAE standard grades oils by their viscosity. The API classification specifies the quality and performance rating of engine oils. Use SG or higher oils, excluding oils marked as “Energy Conserving” or “Resource Conserving” on the circular API service symbol. Not recommended Recommended 14 CTX700-32MJF8000.book 57 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals Brake Fluid NOTICE Brake fluid can damage plastic and painted surfaces. Wipe up spills immediately and wash thoroughly. Also inspect the engine sprocket and rear wheel sprocket. If either has worn or damaged teeth, have the sprocket replaced by your dealer. Maintenance Do not add or replace brake fluid, except in an emergency. Use only fresh brake fluid from a sealed container. If you do add fluid, have the brake system serviced by your dealer as soon as possible. If the chain does not move smoothly, makes strange noises, has damaged rollers or loose pins or missing O-rings, or kinks, have the chain inspected by your dealer. Recommended brake fluid: Honda DOT 4 Brake Fluid or equivalent Normal (GOOD) Worn (REPLACE) Damaged (REPLACE) Drive Chain The drive chain must be inspected and lubricated regularly. Inspect the chain more frequently if you often ride on bad roads, ride at high speed, or ride with repeated fast acceleration. NOTICE Use of a new chain with worn sprockets will cause rapid chain wear. continued 57 14 CTX700-32MJF8000.book 58 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals ❙ Cleaning and Lubricating Maintenance After inspecting the slack, clean the chain and sprockets while rotating the rear wheel. Use dry cloth with chain cleaner designed specifically for O-ring chains, or neutral detergent. Use a soft brush if the chain is dirty. After cleaning, wipe dry and lubricate with the recommended lubricant. If not available, use SAE 80 or 90 gear oil. Do not use a steam cleaner, a high pressure cleaner, a wire brush, volatile solvent such as petrol and benzene, abrasive cleaner, chain cleaner or lubricant NOT designed specifically for O-ring chains as these can damage the rubber O-ring seals. Avoid getting lubricant on the brakes or tyres. Avoid applying excess chain lubricant to prevent spray onto your clothes and the motorcycle. Recommended lubricant: Drive chain lubricant designed specifically for O-ring chains. If not available, use SAE 80 or 90 gear oil. Pro Honda HP coolant is a pre-mixed solution of antifreeze and distilled water. Recommended Coolant Concentration: 50% antifreeze and 50% distilled water A concentration of antifreeze below 40% will not provide proper corrosion and cold temperature protection. 58 14 CTX700-32MJF8000.book 59 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals A concentration of up to 60% will provide better protection in colder climates. Crankcase Breather Service more frequently when riding in rain, at full throttle, or after the motorcycle is washed or overturned. Service if the deposit level can be seen in the transparent section of the drain tube. If the drain tube overflows, the air filter may become contaminated with engine oil causing poor engine performance. Tyres (Inspecting/Replacing) ❙ Checking the Air Pressure ❙ Inspecting for Damage Inspect the tyres for cuts, slits, or cracks that exposes fabric or cords, or nails or other foreign objects embedded in the side of the tyre or the tread. Also inspect for the bumps or bulges in the side walls of the tyres. Maintenance NOTICE Using coolant not specified for aluminium engines or ordinary tap water can cause corrosion. your tyres are cold. ❙ Inspecting for Abnormal Wear Inspect the tyres for signs of abnormal wear on the contact surface. Visually inspect your tyres and use an air pressure gauge to measure the air pressure at least once a month or any time you think the tyres look low. Always check air pressure when continued 59 14 CTX700-32MJF8000.book 60 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals ❙ Inspecting Tread Depth Inspect the tread wear indicators. If they become visible, replace the tyres immediately. For safe riding, you should replace the tyres when the minimum tread depth is reached. Maintenance or TWI Wear indicator location mark 60 3 WARNING Riding on tyres that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tyre inflation and maintenance. Germany German law prohibits use of tyres whose tread depth is less than 1.6 mm. 14 CTX700-32MJF8000.book 61 ページ 2013年5月9日 木曜日 午後9時59分 Maintenance Fundamentals 3 WARNING Installing improper tyres on your motorcycle can adversely affect handling and stability, and can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tyres recommended in this owner’s manual. Maintenance Have your tyres replaced by your dealer. For recommended tyres, air pressure and minimum tread depth, see “Specifications.” 2 P. 129 Follow these guidelines whenever you replace tyres. ● Use the recommended tyres or equivalents of the same size, construction, speed rating, and load range. ● Have the wheel balanced with Honda Genuine balance weights or equivalents after the tyre is installed. ● Do not install a tube inside a tubeless tyre on this motorcycle. Excessive heat build-up can cause the tube to burst. ● Use only tubeless tyres on this motorcycle. The rims are designed for tubeless tyres, and during hard acceleration or braking, a tubetype tyre could slip on the rim and cause the tyre to rapidly deflate. 61 14 CTX700-32MJF8000.book 62 ページ 2013年5月9日 Maintenance Fundamentals Air Cleaner Maintenance 62 This motorcycle is equipped with a viscous type air cleaner element. Air blow cleaning or any other cleaning can degrade the viscous element performance and cause the intake of dust. Do not perform the maintenance. Should be serviced by your dealer. 木曜日 午後9時59分 14 CTX700-32MJF8000.book 63 ページ 2013年5月9日 木曜日 午後9時59分 Tool kit The tool kit is stored under the seat. 2 P. 64 Spark plug wrench 8 × 12 mm Open end wrench ● 10 × 14 mm Open end wrench ● 12 × 14 mm Open end wrench ● Standard/Phillips screwdriver ● Screwdriver grip ● Extension bar ● 5 mm Hex wrench ● 22 mm Box end wrench ● 27 mm Box end wrench ● Helmet set wire ● Fuse puller ● ● Maintenance You can perform some roadside repairs, minor adjustments and parts replacement with the tools contained in the kit. 63 14 CTX700-32MJF8000.book 64 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components ❙ Removal Seat Front stay Prongs Maintenance Seat Seat lock Rear stays 64 Ignition key 1. Insert the ignition key into the seat lock, and turn it clockwise. 2. Pull the seat back and up. ❙ Installation 1. Insert the front and rear prongs into the front and rear stays on the frame. 2. Push forward and down on the rear of the seat until it locks in place. Make sure that the seat is locked securely in position by pulling it up lightly. The seat locks automatically when closed. Take care not to lock your key in the under seat compartment. 14 CTX700-32MJF8000.book 65 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components u Right Under Cowl Lid Right Under Cowl Lid Clip Right under cowl lid The right under cowl lid must be removed to service the coolant reserve tank and brake light switch. 1. Remove the clip. 2 P. 68 2. Remove the right under cowl lid. ❙ Installation Maintenance ❙ Removal Install the parts in the reverse order of removal. 65 14 CTX700-32MJF8000.book 66 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components u Centre Lower Cowl Centre Lower Cowl The centre lower cowl must be removed to service the coolant reserve tank. ❙ Removal Maintenance 1. Remove the right under cowl lid. 2 P. 65 2. Remove the bolts and clips. 2 P. 68 3. Remove the centre lower cowl. ❙ Installation Install the parts in the reverse order of removal. Bolts Bolts Clips Centre lower cowl 66 14 CTX700-32MJF8000.book 67 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components u Right Under Cowl Right Under Cowl The right under cowl must be removed to service the clutch oil filter. CTX700D only ❙ Removal Washer 1. 2. 3. 4. Drain tube Remove the right under cowl lid. 2 P. 65 Remove the centre lower cowl. 2 P. 66 Remove the bolts and washers. Remove the right under cowl by releasing the drain tube. Maintenance Inner side of the right under cowl ❙ Installation 1. Route the drain tube inner side of the right under cowl as shown in the image. 2. Install the parts in the reverse order of removal. Bolts Right under cowl Washer Bolt 67 14 CTX700-32MJF8000.book 68 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components u Clip ❙ Installation Clip The clip must be removed to remove the right under cowl lid and centre lower cowl. Maintenance 68 !a ❙ Removal 1. Loosen the pin by a Phillips screwdriver. 2. Pull the clip out of the hole. !a 1. Insert the clip into the hole. 2. Push the pin in. !b !b 14 CTX700-32MJF8000.book 69 ページ 2013年5月9日 木曜日 午後9時59分 Removing & Installing Body Components u Battery ❙ Removal Battery Positive terminal Negative terminal Maintenance Make sure the ignition switch is off. 1. Remove the seat. 2 P. 64 2. Unhook the rubber strap. 3. Disconnect the negative - terminal from the battery. 4. Disconnect the positive + terminal from the battery. 5. Remove the battery taking care not to drop the terminal nuts. ❙ Installation Rubber strap Battery Install the parts in the reverse order of removal. Always connect the positive + terminal first. Make sure that bolts and nuts are tight. The clock will be reset AM 1:00 if the battery is disconnected. For proper handling of the battery, see “Maintenance Fundamentals.“ 2 P. 54 “Battery Goes Dead.“ 2 P. 109 69 14 CTX700-32MJF8000.book 70 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil Checking the Engine Oil Maintenance 70 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait 2 to 3 minutes. 3. Place your motorcycle in an upright position on a firm, level surface. 4. Remove the oil fill cap/dipstick and wipe it clean. 5. Insert the oil fill cap/dipstick until it seats, but don’t screw it in. Check that the oil level is between the upper and lower level marks in the oil fill cap/dipstick. 6. Securely install the oil fill cap/dipstick. CTX700A Oil fill cap/dipstick Upper level Lower level 14 CTX700-32MJF8000.book 71 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil u Adding Engine Oil CTX700D Oil fill cap/dipstick Lower level Adding Engine Oil If the engine oil is below or near the lower level mark, add the recommended engine oil. 2 P. 56 1. Add the recommended oil until it reaches the upper level mark. Maintenance Upper level u Place your motorcycle in an upright position on a firm, level surface when checking the oil level. u Do not overfill above the upper level mark. u Make sure no foreign objects enter the oil filler opening. u Wipe up any spills immediately. 2. Securely reinstall the oil fill cap/dipstick. NOTICE Overfilling with oil or operating with insufficient oil can cause damage to your engine. Do not mix different brands and grades of oil. They may affect lubrication and clutch operation. For the recommended oil and oil selection guidelines, see “Maintenance Fundamentals.” 2 P. 56 71 14 CTX700-32MJF8000.book 72 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil u Changing Engine Oil & Filter Changing Engine Oil & Filter Maintenance 72 Drain bolt Changing the oil and filter requires special tools. We recommend that you have your motorcycle serviced by your dealer. Use a new Honda Genuine oil filter or equivalent specified for your model. NOTICE Using the wrong oil filter can result in serious damage to the engine. Sealing washer 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait for 2 to 3 minutes. 3. Park on a firm, level surface and lower the side stand. 4. Place a drain pan under the drain bolt. 5. Remove the oil fill cap/dipstick, drain bolt, and sealing washer to drain the oil. 6. Remove the oil filter with a filter wrench and let the remaining oil drain out. Make sure the prior seal is not stuck to the engine. u Discard the oil and oil filter at an approved recycling centre. 14 CTX700-32MJF8000.book 73 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil u Changing Engine Oil & Filter Rubber seal 7. Apply a thin coat of engine oil to the rubber seal of a new oil filter. 8. Install a new oil filter and tighten. Torque: 26 N·m (2.7 kgf·m, 19 lbf·ft). 9. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft). Required oil CTX700A When changing oil & engine oil filter: 3.4 litres (3.6 US qt, 3.0 Imp qt) When changing oil only: 3.1 litres (3.3 US qt, 2.7 Imp qt) CTX700D When changing oil & engine oil filter: 3.4 litres (3.6 US qt, 3.0 Imp qt) When changing oil only: 3.2 litres (3.4 US qt, 2.8 Imp qt) Maintenance Oil filter 10. Fill the crankcase with the recommended oil (2 P. 56) and install the oil fill cap/ dipstick. 11. Check the oil level. 2 P. 70 12. Check that there are no oil leaks. 73 14 CTX700-32MJF8000.book 74 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil u Changing Clutch Oil Filter Changing Clutch Oil Filter CTX700D only Maintenance Use a new Honda Genuine clutch oil filter or equivalent specified for your model. 3. Remove the clutch oil filter cover, clutch oil filter and spring by removing the clutch oil filter cover bolts. u Discard the oil and clutch oil filter at an approved recycling centre. NOTICE Using the wrong clutch oil filter can result in serious damage to the transmission. 1. Follow the steps 1-6 of Changing Engine Oil & Filter. 2 P. 72 2. Remove the right under cowl. 2 P. 67 Rubber seal Clutch oil filter cover OUT-SIDE mark Spring O-ring Bolts 74 Clutch oil filter 14 CTX700-32MJF8000.book 75 ページ 2013年5月9日 木曜日 午後9時59分 Engine Oil u Changing Clutch Oil Filter 10. Install a new sealing washer onto the drain bolt. Install the drain bolt and tighten. Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft). 11. Fill the crankcase with the recommended oil (2 P. 56) and install the oil fill cap/ dipstick. Required oil When changing oil, engine oil filter & clutch oil filter: 3.4 litres (3.6 US qt, 3.0 Imp qt) Maintenance 4. Install the new clutch oil filter with the rubber seal facing in, toward the engine. You will see “OUT-SIDE“ mark on the clutch oil filter body, toward the filter cover. 5. Replace the O-ring and apply a thin coat of engine oil to the new O-ring before installing it. 6. Install the spring and the clutch oil filter cover. 7. Install the clutch oil filter cover bolts and tighten. 8. Apply a thin coat of engine oil to the rubber seal of a new engine oil filter. 2 P. 73 9. Install a new engine oil filter and tighten. 12. Check the oil level. 2 P. 71 13. Check that there are no oil leaks. 14. Install the right under cowl. Torque: 26 N·m (2.7 kgf·m, 19 lbf·ft). 75 14 CTX700-32MJF8000.book 76 ページ 2013年5月9日 木曜日 午後9時59分 Coolant Checking the Coolant Maintenance 1. Place your motorcycle on a firm, level surface. 2. Hold your motorcycle in an upright position. 3. Check that the coolant level is between the UPPER and LOWER level marks in the reserve tank. UPPER level LOWER level 76 Reserve tank If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a serious leak. Have your motorcycle inspected by your dealer. Adding Coolant If the coolant level is below the LOWER level, add the recommended coolant (2 P. 58) until the level reaches the UPPER level mark. Add fluid only from the reserve tank cap and do not remove radiator cap. 14 CTX700-32MJF8000.book 77 ページ 2013年5月9日 木曜日 午後9時59分 Coolant u Changing Coolant 3 WARNING Removing the radiator cap while the engine is hot can cause the coolant to spray out, potentially scalding you. Always let the engine and radiator cool down before removing the radiator cap. Maintenance 1. Remove the centre lower cowl. 2 P. 66 2. Remove the reserve tank cap and add fluid while monitoring the coolant level. u Do not overfill above the UPPER level mark. u Make sure no foreign objects enter the reserve tank opening. 3. Securely reinstall the cap. 4. Install the centre lower cowl. Reserve tank cap Changing Coolant Have your dealer change the coolant unless you have the proper tools and are mechanically qualified. 77 14 CTX700-32MJF8000.book 78 ページ 2013年5月9日 木曜日 午後9時59分 Brakes Checking Brake Fluid Maintenance 1. Place your motorcycle in an upright position on a firm, level surface. 2. Front Check that the brake fluid reservoir is horizontal and that the fluid level is above the LOWER level mark. Rear Check that the brake fluid reservoir is horizontal and that the fluid level is between the LOWER level and UPPER level marks. Front If the brake fluid level in either reservoir is below the LOWER level mark or the brake lever and pedal freeplay becomes excessive, inspect the brake pads for wear. If the brake pads are not worn, you most likely have a leak. Have your motorcycle inspected by your dealer. Rear Front brake fluid reservoir UPPER level mark LOWER level mark LOWER level mark 78 Rear brake fluid reservoir 14 CTX700-32MJF8000.book 79 ページ 2013年5月9日 木曜日 午後9時59分 Brakes u Inspecting the Brake Pads Inspecting the Brake Pads Front Rear Pads Pads Wear indicator Maintenance Check the condition of the brake pad groove wear indicators. The pads need to be replaced if a brake pad is worn to the indicator. 1. Front Inspect the brake pads from below the brake caliper. 2. Rear Inspect the brake pads from the rear right of the motorcycle. If necessary have the pads replaced by your dealer. Always replace both left and right brake pads at the same time. Disc Wear indicator Wear indicator Disc Wear indicator 79 14 CTX700-32MJF8000.book 80 ページ 2013年5月9日 木曜日 午後9時59分 Brakes u Inspecting the Parking Brake Inspecting the Parking Brake CTX700D only Maintenance If the efficacy of the parking brake become weak, have the brake adjusted by your dealer. Parking brake lever 80 Place your motorcycle on a firm, level surface. Stop the engine and push your motorcycle while applying the parking brake lever to check the efficacy of the parking brake. 14 CTX700-32MJF8000.book 81 ページ 2013年5月9日 木曜日 午後9時59分 Side Stand 3. CTX700A Sit on the motorcycle, put the transmission in Neutral, and raise the side stand. Side stand spring 1. Check that the side stand operates smoothly. If the side stand is stiff or squeaky, clean the pivot area and lubricate the pivot bolt with clean grease. 2. Check the spring for damage or loss of tension. 4. CTX700A Start the engine, pull the clutch lever in, and shift the transmission into gear. Maintenance CTX700D Sit on the motorcycle and raise the side stand. CTX700D Start the engine and press the D/S side of N-D switch to switch the transmission into D mode. 5. Lower the side stand all the way. The engine should stop as you lower the side stand. If the engine doesn’t stop, have your motorcycle inspected by your dealer. 81 14 CTX700-32MJF8000.book 82 ページ 2013年5月9日 木曜日 午後9時59分 Drive Chain Inspecting the Drive Chain Slack Maintenance Check the drive chain slack at several points along the chain. If the slack is not constant at all points, some links may be kinked and binding. Have the chain inspected by your dealer. 3. Check the slack in the lower half of the drive chain midway between the sprockets. Drive chain slack: 25 to 35 mm (1.0 to 1.4 in) u Do not ride your motorcycle if the slack exceeds 50 mm (2.0 in). 1. Place your motorcycle on the side stand on a level surface. 2. Stop the engine. Place the transmission in Neutral. 4. Roll the motorcycle forward and check that the chain moves smoothly. 82 14 CTX700-32MJF8000.book 83 ページ 2013年5月9日 木曜日 午後9時59分 Drive Chain u Adjusting the Drive Chain Slack 5. Inspect the sprockets. 2 P. 57 6. Clean and lubricate the drive chain. 2 P. 58 Pulser ring Adjusting the chain requires special tools. Have the drive chain slack adjusted by your dealer. Rear axle nut Lock nut When adjusting the drive chain slack, be careful not to damage the wheel speed sensor and pulser ring. 1. Place your motorcycle on the side stand on a level surface. 2. Stop the engine place the gear in Neutral. 3. Loosen the rear axle nut. 4. Loosen the lock nuts on both sides of the swingarm. Adjusting nut Maintenance Adjusting the Drive Chain Slack Wheel speed sensor Rear edge of adjusting slot Chain adjuster index mark Adjusting nut Lock nut continued 83 14 CTX700-32MJF8000.book 84 ページ 2013年5月9日 木曜日 午後9時59分 Drive Chain u Adjusting the Drive Chain Slack Maintenance 84 5. Turn both adjusting nuts an equal number of turns until the correct drive chain slack is obtained. Turn the adjusting nuts clockwise to tighten the chain. Turn the adjusting nuts counterclockwise to provide more slack. Adjust the slack at a point midway between the front sprocket and the rear wheel sprocket. Check the drive chain slack. 2 P. 82 6. Check rear axle alignment by making sure the chain adjuster index marks align with the rear edge of the adjusting slots. Both marks should correspond. If the axle is misaligned, turn the right or left adjusting nuts until the marks are aligned and recheck chain slack. 7. Remove the bolts and muffler end cover. Bolts Muffler end cover 8. Tighten the rear axle nut. Torque: 98 N·m (10.0 kgf·m, 72 lbf·ft). 9. Install the muffler end cover and bolts. Torque: 10 N·m (1.0 kgf·m, 7 lbf·ft). 14 CTX700-32MJF8000.book 85 ページ 2013年5月9日 木曜日 午後9時59分 Drive Chain u Adjusting the Drive Chain Slack 10. Tighten the drive chain adjusting nuts lightly, then hold the adjusting nuts and tighten the lock nuts. Torque: 21 N·m (2.1 kgf·m, 15 lbf·ft). If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. Check the chain wear label when adjusting the drive chain. If the arrow mark on the chain adjuster plate enters the red zone on the label after the chain has been adjusted to the proper slack, the chain is excessively worn and must be replaced. Chain: DID 520V0 or RK 520KHO Maintenance 11. Recheck drive chain slack. ❙ Checking the Drive Chain Wear If necessary, have the drive chain replaced by your dealer. Red zone Arrow mark 85 14 CTX700-32MJF8000.book 86 ページ 2013年5月9日 Drive Chain u Checking the Drive Chain Slider Checking the Drive Chain Slider Maintenance Check the condition of the drive chain slider. The drive chain slider need to be replaced if it is worn to the wear limit line. If necessary have the drive chain slider replaced by your dealer. Drive chain slider Wear limit line Wear limit line 86 木曜日 午後9時59分 14 CTX700-32MJF8000.book 87 ページ 2013年5月9日 木曜日 午後9時59分 Clutch Checking the Clutch CTX700A only ❙ Checking the Clutch Lever Freeplay Freeplay at the clutch lever: 10 to 20 mm (0.4 to 0.8 in) Maintenance Check the clutch lever freeplay. Check the clutch cable for kinks or signs of wear. If necessary have it replaced by your dealer. Lubricate the clutch cable with a commercially available cable lubricant to prevent premature wear and corrosion. Clutch lever Freeplay 87 14 CTX700-32MJF8000.book 88 ページ 2013年5月9日 木曜日 午後9時59分 Clutch u Adjusting the Clutch Lever Freeplay Adjusting the Clutch Lever Freeplay Upper lock nut – CTX700A only Maintenance ❙ Upper Adjustment Attempt adjustment with the upper clutch cable adjuster first. + 1. Loosen the upper lock nut. 2. Turn the upper clutch cable adjuster until the freeplay is 10 to 20 mm (0.4 to 0.8 in). 3. Tighten the upper lock nut and check the freeplay again. Upper clutch cable adjuster ❙ Lower Adjustment If the upper clutch cable adjuster is threaded out near its limit, or the correct freeplay cannot be obtained, attempt adjustment with the lower adjusting nut. 88 14 CTX700-32MJF8000.book 89 ページ 2013年5月9日 木曜日 午後9時59分 Clutch u Adjusting the Clutch Lever Freeplay Lower adjusting nut + – Maintenance 1. Loosen the upper lock nut and turn the upper clutch cable adjuster all the way in (to provide maximum freeplay). Tighten the upper lock nut. 2. Loosen the lower lock nut. 3. Turn the lower adjusting nut until the clutch lever freeplay is 10 to 20 mm (0.4 to 0.8 in). 4. Tighten the lower lock nut and check the clutch lever freeplay. 5. Start the engine, pull the clutch lever in, and shift into gear. Make sure the engine does not stall and the motorcycle does not creep. Gradually release the clutch lever and open the throttle. Your motorcycle should move smoothly and accelerate gradually. Lower lock nut If proper adjustment cannot be obtained or the clutch does not work correctly, see your dealer. 89 14 CTX700-32MJF8000.book 90 ページ 2013年5月9日 Throttle Checking the Throttle Maintenance With the engine off, check that the throttle rotates smoothly from fully closed to fully open in all steering positions and throttle freeplay is correct. If the throttle does not move smoothly, close automatically, or if the cable is damaged, have the motorcycle inspected by your dealer. Freeplay at the throttle grip flange: 2 to 6 mm (0.1 to 0.2 in) Freeplay Flange 90 木曜日 午後9時59分 14 CTX700-32MJF8000.book 91 ページ 2013年5月9日 木曜日 午後9時59分 Crankcase Breather Cleaning the Crankcase Breather Maintenance 1. Remove the crankcase breather tube plug from the tube. 2. Drain deposits into a suitable container. 3. Install the crankcase breather tube plug. Crankcase breather tube plug 91 14 CTX700-32MJF8000.book 92 ページ 2013年5月9日 木曜日 午後9時59分 Other Adjustments Adjusting the Headlight Aim Maintenance 92 You can adjust vertical aim of the headlight for proper alignment. Turn the pinion using a Phillips screwdriver provided in the tool kit (2 P. 63) in or out as necessary. Obey local laws and regulations. Pinion Lower Raise 14 CTX700-32MJF8000.book 93 ページ 2013年5月9日 木曜日 午後9時59分 Other Adjustments u Adjusting the Brake Light Switch Adjusting the Brake Light Switch Brake light switch Maintenance Check the operation of the brake light switch. 1. Remove the right under cowl lid by removing the clip. 2 P. 65 2. Hold the brake light switch and turn the adjusting nut in the direction A if the switch operates too late, or turn the nut in the direction B if the switch operates too soon. A B Adjusting nut 93 14 CTX700-32MJF8000.book 94 ページ 2013年5月9日 木曜日 午後9時59分 Troubleshooting Engine Will Not Start (HISS indicator stays on) ......................................................... P. 95 Overheating (High coolant temperature indicator is on)..........................................P. 96 Warning Indicators On or Flashing ...........P. 97 Low Oil Pressure Indicator..........................P. 97 PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) ............P. 97 ABS (Anti-lock Brake System) Indicator ......P. 98 If the “-” Indicator is Blinking in the Gear Position Window While Riding............... P. 99 Other Warning Indication ....................... P. 100 Fuel Gauge Failure Indication .................. P. 100 Tyre Puncture........................................... P. 101 Electrical Trouble ..................................... P. 109 Battery Goes Dead .................................. P. 109 Burned-out Light Bulb............................. P. 109 Blown Fuse ............................................. P. 113 14 CTX700-32MJF8000.book 95 ページ 2013年5月9日 木曜日 午後9時59分 Engine Will Not Start (HISS indicator stays on) ❙ Starter Motor Operates But Engine Does Not Start ❙ Starter Motor Does Not Operate Check the following items: ● Make sure engine stop switch is (Run) position 2 P. 30, 33 ● Check for a blown fuse 2 P. 113 ● Check for a loose battery connection or battery terminal corrosion 2 P. 69 ● Check the condition of the battery 2 P. 109 If the problem continues, have your motorcycle inspected by your dealer. Troubleshooting Check the following items: ● Check the correct engine starting sequence 2 P. 34 ● Check that there is petrol in the fuel tank ● Check if the PGM-FI malfunction indicator lamp (MIL) is on u If the indicator light is on, contact your dealer as soon as possible. ● Check if the HISS indicator stays on u Turn the ignition switch to the OFF position and remove the key. Reinsert the key and turn the ignition switch to the ON position. If the indicator still stays on, check the following: Check if there is no another HISS key (including spare key) close to the ignition switch. Check if there are no any metallic seals or stickers on the key. If the HISS indicator still stays on, have your motorcycle inspected by your dealer. 95 14 CTX700-32MJF8000.book 96 ページ 2013年5月9日 木曜日 午後9時59分 Overheating (High coolant temperature indicator is on) Troubleshooting The engine is overheating when the following occurs: ● High coolant temperature indicator comes on ● Acceleration becomes sluggish ● If this occurs, pull safely to the side of the road and perform the following procedure. Extended fast idling may cause the high coolant temperature indicator comes on. NOTICE Continuing to ride with an overheated engine can cause serious damage to the engine. 2. Check that the radiator fan is operating, and then turn the ignition switch to the OFF position. If the fan is not operating: Suspect a fault. Do not start the engine. Transport your motorcycle to your dealer. If the fan is operating: Allow the engine to cool with the ignition switch in the OFF position. 3. After the engine has cooled, inspect the radiator hose and check if there is a leak. 2 P. 76 If there is a leak: 1. Stop the engine using the ignition switch, and then turn the ignition switch to the ON position. 96 Do not start the engine. Transport your motorcycle to your dealer. 4. Check the coolant level in the reserve tank, and add coolant as necessary. 2 P. 76 5. If 1–4 check normal, you may continue riding, but closely monitor the high coolant temperature indicator. 14 CTX700-32MJF8000.book 97 ページ 2013年5月9日 木曜日 午後9時59分 Warning Indicators On or Flashing Low Oil Pressure Indicator If the low oil pressure indicator comes on, pull safely to the side of the road and stop the engine. 1. Check the engine oil level, and add oil as necessary. 2 P. 70 2. Start the engine. u Only continue riding if the low oil pressure indicator goes off. Rapid acceleration may momentarily cause the low oil pressure indicator to come on, especially if the oil is at or near the low level. If the low oil pressure indicator stays on when the oil level is at the proper level, stop the engine and contact your dealer. PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) If the indicator comes on while riding, you may have a serious problem with the PGM-FI system. Reduce speed and have your motorcycle inspected by your dealer as soon as possible. Troubleshooting NOTICE Continuing to ride with low oil pressure can cause serious damage to the engine. If the engine oil level goes down rapidly, your motorcycle may have a leak or another serious problem. Have your motorcycle inspected by your dealer. 97 14 CTX700-32MJF8000.book 98 ページ 2013年5月9日 木曜日 午後9時59分 Warning Indicators On or Flashing u ABS (Anti-lock Brake System) Indicator ABS (Anti-lock Brake System) Indicator Troubleshooting 98 If the indicator operates in one of the following ways, you may have a serious problem with the brake system. Reduce your speed and have your motorcycle inspected by your dealer as soon as possible. Indicator comes on or starts flashing while riding. ● Indicator does not come on when the ignition switch is in the ON position. ● Indicator does not go off at speeds above 10 km/h (6 mph). ● If the ABS indicator stays on, your brakes will continue to work as a conventional system, but without the anti-locking function. The ABS indicator may flash if you turn the rear wheel while your motorcycle is lifted off the ground. In this case, turn the ignition switch off and then on again. The ABS indicator will go off after your speed reaches 30 km/h (19 mph). 14 CTX700-32MJF8000.book 99 ページ 2013年5月9日 木曜日 午後9時59分 If the “-” Indicator is Blinking in the Gear Position Window While Riding CTX700D only If you cannot start the engine: Start the engine while applying the brake lever or pressing the brake pedal. If you can shift from N to D mode: When a gear position is shown in the gear position indicator, you can ride in that gear. Take your motorcycle to your dealer riding at a safe speed. If you can’t shift from N to D mode and the “-” indicator is blinking: Troubleshooting If the “-” indicator is blinking while riding, you may have a serious problem with the Dual Clutch Transmission system. Park your motorcycle in a safe place and have your motorcycle inspected by dealer immediately. There is possibility for you to ride yourself to go to dealer if you try to follow the procedure below. 1. Turn the ignition switch to OFF. 2. Turn the ignition switch to ON and start the engine. If you still cannot start the engine: Damage is preventing you from riding. Have your motorcycle inspected by your dealer immediately. Turn the ignition switch to OFF and move the motorcycle back and forth slightly (to disengage the gears). Turn the ignition switch to ON again and start the engine. 99 14 CTX700-32MJF8000.book 100 ページ 2013年5月9日 Other Warning Indication Fuel Gauge Failure Indication Troubleshooting 100 If the fuel system has an error, the fuel gauge indicators will be displayed as shown in the illustration. If this occurs, see your dealer as soon as possible. 木曜日 午後9時59分 14 CTX700-32MJF8000.book 101 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture Repairing a puncture or removing a wheel requires special tools and technical expertise. We recommend you have this type of service performed by your dealer. After an emergency repair, always have the tyre inspected/replaced by your dealer. If your tyre has a minor puncture, you can make an emergency repair using a tubeless tyre repair kit. Follow the instructions provided with the emergency tyre repair kit. Riding your motorcycle with a temporary tyre repair is very risky. Do not exceed 50 km/h (30 mph). Have the tyre replaced by your dealer as soon as possible. Riding your motorcycle with a temporary tyre repair can be risky. If the temporary repair fails, you can crash and be seriously injured or killed. If you must ride with a temporary tyre repair, ride slowly and carefully and do not exceed 50 km/h (30 mph) until the tyre is replaced. Troubleshooting Emergency Repair Using a Tyre Repair Kit 3 WARNING Removing Wheels Follow these procedures if you need to remove a wheel in order to repair a puncture. continued 101 14 CTX700-32MJF8000.book 102 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels When removing and installing the wheel, be careful not to damage the wheel speed sensor and pulser ring. ❙ Front Wheel Troubleshooting Removal Tape or cloth Pulser ring Brake caliper 102 Mounting bolts Side collar Wheel speed sensor 1. Park on a firm, level surface. 2. Cover right side of the front wheel and brake caliper with protective tape or cloth. 3. On the right side, remove the mounting bolts and remove the brake caliper. u Support the brake caliper assembly so that it doesn’t hang from the brake hose. Do not twist the brake hose. u Avoid getting grease, oil, or dirt on the disc or pad surfaces. u Do not pull the brake lever while the brake caliper is removed. u Take care to prevent the brake caliper from scratching the wheel during removal. 14 CTX700-32MJF8000.book 103 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels Side collar Front axle shaft Installation 1. Attach the side collars to the wheel. 2. On the left side, place the wheel between the fork legs and insert the front axle shaft to the end, through the left fork leg and wheel hub. 3. Tighten the axle shaft. Torque: 74 N·m (7.5 kgf·m, 55 lbf·ft). Troubleshooting 4. Loosen the axle pinch bolt and front axle shaft. 5. Support your motorcycle securely and raise the front wheel off the ground using a maintenance stand or a hoist. 6. Remove the front axle shaft, front wheel and side collars. Axle pinch bolt continued 103 14 CTX700-32MJF8000.book 104 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels 4. Install the brake caliper and tighten the mounting bolts. Torque: 30 N·m (3.1 kgf·m, 22 lbf·ft). Troubleshooting u Take care to prevent the brake caliper from scratching the wheel during installation. u Use new mounting bolts when installing the brake caliper. NOTICE When installing the brake caliper into position on the fork leg, carefully fit the brake disc between the pads to avoid scratching them. 5. Lower the front wheel on the ground. 6. Apply the brake lever and pump the fork several times. 7. Tighten the axle pinch bolt. Torque: 22 N·m (2.2 kgf·m, 16 lbf·ft). 104 8. Raise the front wheel off the ground again, and check that the wheel rotates freely after you release the brake. 9. Uncover the protective tape or cloth. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. 14 CTX700-32MJF8000.book 105 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels ❙ Rear Wheel Mounting bolts Parking brake caliper Troubleshooting Removal 1. Support your motorcycle securely and raise the rear wheel off the ground using a maintenance stand or a hoist. 2. CTX700D only Release the parking brake. 3. CTX700D only Remove the mounting bolts and remove the parking brake caliper. CTX700D only continued 105 14 CTX700-32MJF8000.book 106 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels Troubleshooting 4. Loosen the rear axle nut, lock nuts and turn the adjusting nuts so the rear wheel can be moved all the way forward for maximum drive chain slack. 5. Remove the drive chain from the rear wheel sprocket by pushing the rear wheel forward. 6. Remove the rear axle nut, washer A and washer B. 7. Remove the rear axle shaft, washer B, brake caliper bracket, rear wheel and side collars. u Support the brake caliper assembly so that it doesn’t hang from the brake hose. Do not twist the brake hose. u Avoid getting grease, oil, or dirt on the disc to pad surfaces. u Do not push the brake pedal while the wheel is removed. Right side collar Pulser ring Wheel speed sensor Washer A Rear axle nut Washer B Lock nut Adjusting nut Left side collar Rear axle shaft Lock nut CTX700D only u Do not pull the parking brake lever while the wheel is removed. 106 Drive chain Washer B Adjusting nut 14 CTX700-32MJF8000.book 107 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels 3. Make sure that the slot on the brake caliper bracket is positioned in the lug on the swingarm. Brake caliper bracket NOTICE When installing the brake caliper into position, carefully fit the brake disc between the pads to avoid scratching them. Lug Slot Troubleshooting Installation 1. Attach the right and left side collars in their original locations on the wheel. 2. To install the rear wheel, reverse the removal procedure. u Take care to prevent the brake caliper from scratching the wheel during installation. Swingarm continued 107 14 CTX700-32MJF8000.book 108 ページ 2013年5月9日 木曜日 午後9時59分 Tyre Puncture u Removing Wheels 4. Adjust the drive chain. 2 P. 83 5. Remove the bolts and muffler end cover. 2 P. 84 6. Install and tighten the rear axle nut. Torque: 98 N·m (10.0 kgf·m, 72 lbf·ft). Troubleshooting 7. Install the muffler end cover and bolts. 2 P. 84 8. Tighten the drive chain adjusting nuts lightly, then hold the adjusting nuts and tighten the lock nuts. Torque: 21 N·m (2.1 kgf·m, 15 lbf·ft). 9. After installing the wheel, apply the brake pedal several times, then recheck the wheel rotates freely. Recheck the wheel if the brake drags or if the wheel does not rotate freely. 108 10. CTX700D only Install the parking brake caliper and tighten the mounting bolts. Torque: 31 N·m (3.2 kgf·m, 23 lbf·ft). u Take care to prevent the brake caliper from scratching the wheel during installation. u Use new mounting bolts when installing the parking brake caliper. NOTICE When installing the brake caliper into position, carefully fit the brake disc between the pads to avoid scratching them. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. 14 CTX700-32MJF8000.book 109 ページ 2013年5月9日 木曜日 午後9時59分 Electrical Trouble Burned-out Light Bulb Charge the battery using a motorcycle battery charger. Remove the battery from the motorcycle before charging. Do not use an automobile-type battery charger, as these can overheat a motorcycle battery and cause permanent damage. If the battery does not recover after recharging, contact your dealer. Follow the procedure below to replace a burned-out light bulb. Turn the ignition switch to the OFF or LOCK position. Allow the bulb to cool before replacing it. Do not use bulbs other than those specified. Check the replacement bulb for correct operation before riding. NOTICE Jump starting using an automobile battery is not recommended, as this can damage your motorcycle’s electrical system. For the light bulb wattage, see “Specifications.” 2 P. 130 Troubleshooting Battery Goes Dead continued 109 14 CTX700-32MJF8000.book 110 ページ 2013年5月9日 木曜日 午後9時59分 Electrical Trouble u Burned-out Light Bulb ❙ Headlight Bulb Bulb Dust cover Connector Troubleshooting 110 Pin 1. Pull off the connector without turning. 2. Remove the dust cover. 3. Press the pin down and pull out the bulb without turning it. 4. Install a new bulb and parts in the reverse order of removal. Do not touch the glass surface with your fingers. If you touch the bulb with your bare hands, clean it with a cloth moistened with alcohol. 14 CTX700-32MJF8000.book 111 ページ 2013年5月9日 木曜日 午後9時59分 Electrical Trouble u Burned-out Light Bulb ❙ Brake/Tail Light Bulb ❙ Front/Rear Turn Signal Bulb Brake/tail light 1. Remove the screw and collar. 2. Remove the turn signal lens. 3. Slightly press the bulb and turn it counterclockwise. Bulb The brake and tail light uses several LEDs. If there is a LED which is not turned on, see your dealer for this service. Troubleshooting Turn signal lens Collar Screw 4. Install a new bulb and parts in the reverse order of removal. continued 111 14 CTX700-32MJF8000.book 112 ページ 2013年5月9日 Electrical Trouble u Burned-out Light Bulb ❙ License Plate Light 1. Remove the screws, license light cover and license light cover packing. 2. Pull out the bulb without turning. Troubleshooting License light cover Cover Bulb packing Screws 3. Install a new bulb and parts in the reverse order of removal. 112 木曜日 午後9時59分 14 CTX700-32MJF8000.book 113 ページ 2013年5月9日 木曜日 午後9時59分 Electrical Trouble u Blown Fuse Blown Fuse CTX700A Fuse box cover Before handling fuses, see “Inspecting and Replacing Fuses.” 2 P. 55 ❙ Fuse Box Fuses Troubleshooting 1. Remove the seat. 2 P. 64 2. Remove the fuse box cover. 3. Pull the fuses out with the fuse puller in the tool kit one by one and check for a blown fuse. Always replace a blown fuse with a spare of the same rating. u Spare fuses are provided on the back of the fuse box cover. 4. Install the fuse box cover. 5. Install the seat. Spare fuses CTX700D Fuse box cover Spare fuses continued 113 14 CTX700-32MJF8000.book 114 ページ 2013年5月9日 木曜日 午後9時59分 Electrical Trouble u Blown Fuse ❙ Main Fuse Main fuse Wire connector Troubleshooting NOTICE If a fuse fails repeatedly, you likely have an electrical problem. Have your motorcycle inspected by your dealer. Starter magnetic switch Spare main fuse 1. Remove the seat. 2 P. 64 2. Disconnect the wire connector of the starter magnetic switch. 114 3. Pull the main fuse out with the fuse puller in the tool kit and check for a blown fuse. Always replace a blown fuse with a spare of the same rating. u Spare main fuse is provided in the starter magnetic switch. 4. Install the parts in the reverse order of removal. 14 CTX700-32MJF8000.book 115 ページ 2013年5月9日 木曜日 午後9時59分 Information Keys...........................................................P. 116 Instruments, Controls, & Other Features...P. 117 Fuels Containing Alcohol.........................P. 120 Catalytic Converter ..................................P. 121 Caring for Your Motorcycle.....................P. 122 Storing Your Motorcycle .........................P. 125 Transporting Your Motorcycle ................P. 125 You & the Environment ...........................P. 126 Serial Numbers .........................................P. 127 14 CTX700-32MJF8000.book 116 ページ 2013年5月9日 木曜日 午後9時59分 Keys Keys Ignition key Information The ignition key contains a special coded chip that is recognized by the immobilizer system (HISS) in order to start the engine. Handle the key carefully to prevent damaging the HISS components. ● Do not bend keys or subject them to undue stress. ● Avoid prolonged exposure to sunlight or high temperatures. ● Do not grind, drill or in any way alter their shape. ● Do not expose to strong magnetic objects. If you lose all keys and the key number plate, the PGM-FI unit/ignition control module must be replaced by your dealer. To avoid this, keep a duplicate key. If you lose a key, make another duplicate key immediately. 116 To make a duplicate key and register it with your HISS system, take the spare key, the key number plate, and the motorcycle to your dealer. A metal key holder may cause damage to the area surrounding the ignition switch. 14 CTX700-32MJF8000.book 117 ページ 2013年5月9日 木曜日 午後9時59分 Instruments, Controls, & Other Features Instruments, Controls, & Other Features Ignition Switch Engine Stop Switch Do not use the engine stop switch except in an emergency. Doing so when riding will cause the engine to suddenly turn off, making riding unsafe. If you stop the engine using the engine stop switch, turn the ignition switch off. Failing to do so will drain the battery. Odometer The display locks 999,999 when the read-out exceeds 999,999. The tripmeter A, B returns to 0.0 when the read-out exceeds 999.9. HISS The Honda Ignition Security System (HISS) immobilizes the engine’s ignition system if an improperly-coded key is used to try and start the engine. When the ignition switch is turned off, the HISS immobilizer system is always alert, even if the HISS indicator is not flashing. If the ignition switch is turned on with the engine stop switch in the (Run) position, the HISS indicator turns on and goes off after a few seconds to indicate it is OK to start the engine. 2 HISS Indicator Does Not Turn OFF P. 95 Information The headlight is always on when the ignition switch is on. Leaving the ignition switch on with the engine stopped will drain the battery. Do not turn the key while riding. Tripmeter The HISS indicator starts flashing every 2 seconds for 24 hours after the ignition switch is turned off. To prevent or to restore the HISS indicator flashing: continued 117 14 CTX700-32MJF8000.book 118 ページ 2013年5月9日 木曜日 午後9時59分 Instruments, Controls, & Other Features 1. With the ignition switch on, press and hold the A button (2 P. 22) for 2 seconds or more when the display function mode is odometer. u The HISS indicator flashes once. 2. Turn the ignition switch off. South Africa only Morocco only EC Directive Information This immobilizer system complies with R & TTE (Radio and Telecommunications Terminal Equipment and the mutual recognition of their conformity) Directive. The declaration of conformity to R & TTE Directive is provided to the owner at the time of purchase. The declaration of conformity should be kept at a safe place. When the declaration of conformity is lost or is not provided, contact your dealer. 118 Singapore only 14 CTX700-32MJF8000.book 119 ページ 2013年5月9日 木曜日 午後9時59分 Instruments, Controls, & Other Features Document Bag The owner’s manual, registration, and insurance information can be stored in the plastic document bag located underside of the seat. 2 P. 45 Ignition Cut-off System Information A banking (lean angle) sensor automatically stops the engine and fuel pump if the motorcycle falls over. To reset the sensor, you must turn the ignition switch to OFF and back to the ON position before the engine can be restarted. 119 14 CTX700-32MJF8000.book 120 ページ 2013年5月9日 木曜日 午後9時59分 Fuels Containing Alcohol Fuels Containing Alcohol Some conventional fuels blended with alcohol are available in some locales to help reduce emissions to meet clean air standards. If you plan to use blended fuel, check that it is unleaded and meets the minimum octane rating requirement. Information 120 The following fuel blends can be used in your motorcycle: ● Ethanol (ethyl alcohol) up to 10% by volume. u Petrol containing ethanol may be marketed under the name Gasohol. The use of petrol containing more than 10% ethanol may: ● Damage the painting of the fuel tank. ● Damage the rubber tubes of the fuel line. ● Cause corrosion of the fuel tank. ● Cause poor drivability. NOTICE Use of blended fuels containing higher than approved percentages can damage metal, rubber, plastic parts of your fuel system. If you notice any undesirable operating symptoms or performance problems, try a different brand of petrol. 14 CTX700-32MJF8000.book 121 ページ 2013年5月9日 木曜日 午後9時59分 Catalytic Converter Catalytic Converter A defective catalytic converter contributes to air pollution and can impair your engine’s performance. A replacement unit must be an original Honda part or equivalent. Information This motorcycle is equipped with a three-way catalytic converter. The catalytic converter contain precious metals that serve as catalysts in high temperature chemical reactions that convert hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) in the exhaust gasses into safe compounds. Follow these guidelines to protect your motorcycle’s catalytic converter. ● Always use unleaded petrol. Leaded petrol will damage the catalytic converter. ● Keep the engine in good running condition. ● Have your motorcycle serviced if your engine is misfiring, backfiring, stalling, or otherwise not running properly, stop riding and turn off the engine. 121 14 CTX700-32MJF8000.book 122 ページ 2013年5月9日 木曜日 午後9時59分 Caring for Your Motorcycle Caring for Your Motorcycle Information Frequent cleaning and polishing is important to ensure the long life of your Honda. A clean motorcycle makes it easier to spot potential problems. In particular, seawater and salts used to prevent ice on roads promote the formation of corrosion. Always wash your motorcycle thoroughly after riding on coastal or treated roads. Washing Allow the engine, muffler, brakes, and other high-temperature parts to cool before washing. 1. Rinse your motorcycle thoroughly using a garden hose to remove loose dirt. 2. If necessary, use a sponge or a soft towel with mild cleaner to remove road grime. u Clean the windscreen, headlight lens, panels, and other plastic components with extra care to avoid scratching them. Avoid 122 directing water into the air cleaner, muffler, and electrical parts. 3. Thoroughly rinse your motorcycle with plenty of clean water and dry with a soft, clean cloth. 4. After the motorcycle dries, lubricate any moving parts. u Make sure that no lubricant spills onto the brakes or tyres. Brake discs or pads contaminated with oil will suffer greatly reduced braking effectiveness and can lead to a crash. 5. Lubricate the drive chain immediately after washing and drying the motorcycle. 6. Apply a coat of wax to prevent corrosion. u Avoid products that contain harsh detergents or chemical solvents. These can damage the metal, paint, and plastic on your motorcycle. Keep the wax clear of the tyres and brakes. u If your motorcycle has any matte painted parts, do not apply a coat of wax to the matte painted surface. 14 CTX700-32MJF8000.book 123 ページ 2013年5月9日 木曜日 午後9時59分 Caring for Your Motorcycle ❙ Washing Precautions u Any condensation inside the headlight should dissipate after a few minutes of running the engine. ● Do not use waxes containing compounds at the matte painted surface: u Using plenty of water, clean the matte painted surface with a soft cloth or sponge. Dry with a soft, clean cloth. u Use neutral detergent to clean matte painted surface. Aluminium Components Aluminium will corrode from contact with dirt, mud, or road salt. Clean aluminium parts regularly and follow these guidelines to avoid scratches: ● Do not use stiff brushes, steel wool, or cleaners containing abrasives. ● Avoid riding over or scraping against curbs. Information Follow these guidelines when washing: ● Do not use high-pressure washers: u High-pressure water cleaners can damage moving parts and electrical parts, rendering them inoperable. ● Do not direct water at the muffler: u Water in the muffler can prevent starting and causes rust in the muffler. ● Dry the brakes: u Water adversely affects braking effectiveness. After washing, apply the brakes intermittently at low speed to help dry them. ● Do not direct water under the seat: u Water in the under seat compartment can damage your documents and other belongings. ● Do not direct water at the air cleaner: u Water in the air cleaner can prevent the engine from starting. ● Do not direct water near the headlight: continued 123 14 CTX700-32MJF8000.book 124 ページ 2013年5月9日 木曜日 午後9時59分 Caring for Your Motorcycle Panels Information 124 Follow these guidelines to prevent scratches and blemishes: ● Wash gently using a soft sponge and plenty of water. ● To remove stubborn stains, use diluted detergent and rinse thoroughly with plenty of water. ● Avoid getting petrol, brake fluid, or detergents on the instruments, windscreen, panels, or headlight. Exhaust Pipe and Muffler The exhaust pipe and muffler are stainless steel but may become stained by mud or dust. To remove mud or dust, use a wet sponge and a liquid kitchen abrasive, then rinse well with clean water. Dry with chamois or a soft towel. If necessary, remove heat stains by using a commercially available fine texture compound. Then rinse by the same manner as removing mud or dust. NOTICE Even though the exhaust is made of stainless steel, it can become stained. Remove all marks and blemishes as soon as they are noticed. 14 CTX700-32MJF8000.book 125 ページ 2013年5月9日 木曜日 午後9時59分 Storing Your Motorcycle Storing Your Motorcycle Transporting Your Motorcycle If your motorcycle needs to be transported, it should be carried on a motorcycle trailer or a flatbed truck or trailer that has a loading ramp or lifting platform, and motorcycle tie-down straps. Never try to tow your motorcycle with a wheel or wheels on the ground. Information If you store your motorcycle outdoors, you should consider using a full-body motorcycle cover. If you won’t be riding for an extended period, follow these guidelines: ● Wash your motorcycle and wax all painted surfaces (except matte painted surfaces). Coat chrome pieces with rust-inhibiting oil. ● Lubricate the drive chain. 2 P. 58 ● Place your motorcycle on a maintenance stand and position a block so that both tyres are off the ground. ● After rain, remove the body cover and allow the motorcycle to dry. ● Remove the battery (2 P. 69) to prevent discharge. Charge the battery in a shaded, wellventilated area. u If you leave the battery in place, disconnect the negative - terminal to prevent discharge. After removing your motorcycle from storage, inspect all maintenance items required by the Maintenance Schedule. NOTICE Towing your motorcycle can cause serious damage to the transmission. 125 14 CTX700-32MJF8000.book 126 ページ 2013年5月9日 木曜日 午後9時59分 You & the Environment You & the Environment Owning and riding a motorcycle can be enjoyable, but you must do your part to protect the environment. Choose Sensible Cleaners Information 126 Use a biodegradable detergent when you wash your motorcycle. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Recycle Wastes Put oil and other toxic wastes in approved containers and take them to a recycling centre. Call your local or state office of public works or environmental services to find a recycling centre in your area, and to get instructions on how to dispose of non-recyclable wastes. Do not place used engine oil in the trash, or pour it down a drain or on the ground. Used oil, petrol, coolant, and cleaning solvents contain poisons that can hurt refuse workers and contaminate drinking water, lakes, rivers, and oceans. 14 CTX700-32MJF8000.book 127 ページ 2013年5月9日 木曜日 午後9時59分 Serial Numbers Serial Numbers Frame number Information The frame and engine serial numbers uniquely identify your motorcycle and are required in order to register your motorcycle. They may also be required when ordering replacement parts. The frame number is stamped on the right side of the steering head. The engine number is stamped on the right rear side of the crankcase. You should record these numbers and keep them in a safe place. Engine number 127 14 CTX700-32MJF8000.book 128 ページ 2013年5月9日 木曜日 午後9時59分 Specifications Specifications ■ Main Components Type Overall length Overall width CTX700A CTX700D Overall height Wheelbase Minimum ground clearance Specifications Caster angle Trail Curb weight CTX700A CTX700D Maximum weight capacity*1 Maximum luggage weight (Except KO type) Passenger capacity Minimum turning radius RC69 2,255 mm (88.8 in) Except KO type 855 mm (33.7 in) KO type 825 mm (32.5 in) 840 mm (33.1 in) 1,165 mm (45.9 in) 1,530 mm (60.2 in) 130 mm (5.1 in) Except KO type KO type 114 mm (4.5 in) Except KO type KO type Except KO type KO type 27° 42’ 27° 40’ 226 kg (498 lb) 225 kg (496 lb) 234 kg (516 lb) 190 kg (419 lb) 170 kg (375 lb) 15.5 kg (34 lb) Rider and 1 passenger 3.0 m (9.9 ft) *1 Including rider, passenger, all luggage, and accessories 128 Displacement 670 cm3 (40.9 cu-in) Bore × stroke 73 × 80 mm (2.9 × 3.1 in) Compression ratio 10.7:1 Unleaded petrol Fuel Recommended: 91 RON or higher Tank capacity 12.4 litres (3.28 US gal, 2.73 Imp gal) Battery YTZ12S 12V-11.0Ah (10 HR)/11.6Ah (20 HR) CTX700A 1st 2.812 2nd 1.894 3rd 1.454 4th 1.200 5th 1.033 6th 0.837 Gear ratios CTX700D 1st 2.666 2nd 1.904 3rd 1.454 4th 1.200 5th 1.033 6th 0.837 CTX700A 1.731 / 2.687 Reduction ratios (primary / final) CTX700D 1.921 / 2.437 14 CTX700-32MJF8000.book 129 ページ 2013年5月9日 木曜日 午後9時59分 Specifications ■ Service Data CTX700A Front Rear Engine oil capacity After draining 3.1 litres (3.3 US qt, 2.7 Imp qt) After draining & engine oil filter change 3.4 litres (3.6 US qt, 3.0 Imp qt) After disassembly 3.7 litres (3.9 US qt, 3.3 Imp qt) CTX700D After draining After draining & engine oil filter change After draining, engine & clutch oil filter change After disassembly Recommended brake fluid Cooling system capacity Recommended coolant 3.2 litres (3.4 US qt, 2.8 Imp qt) 3.4 litres (3.6 US qt, 3.0 Imp qt) 3.4 litres (3.6 US qt, 3.0 Imp qt) Specifications 120/70ZR17M/C (58W) 160/60ZR17M/C (69W) Tyre type Radial, tubeless BRIDGESTONE BT023F G Front METZELER ROADTEC Z8 INTERACT E Recommended Tyres BRIDGESTONE BT023R G Rear METZELER ROADTEC Z8 INTERACT Front 250 kPa (2.50 kgf/cm2, 36 psi) [Driver only] Tyre air pressure 250 kPa (2.50 kgf/cm2, 36 psi) Rear [Driver and passenger] 290 kPa (2.90 kgf/cm2, 42 psi) 1.5 mm (0.06 in) Minimum tread Front depth Rear 2.0 mm (0.08 in) Spark plugs (standard) IFR6G-11K (NGK) (non1.00 to 1.10 mm Spark plug gap adjustable) (0.039 to 0.043 in) Idle speed 1,200 ± 100 rpm Honda 4-stroke motorcycle oil API Service Classification SG or higher, excluding oils Recommended marked as “Energy Conserving” or “Resource engine oil Conserving,” SAE 10W-30, JASO T 903 standard MA Tyre size 4.1 litres (4.3 US qt, 3.6 Imp qt) Honda DOT 4 Brake Fluid 1.69 litres (1.79 US qt, 1.49 Imp qt) Pro Honda HP Coolant 129 14 CTX700-32MJF8000.book 130 ページ 2013年5月9日 木曜日 午後9時59分 Specifications Recommended drive chain lubricant Drive chain slack Standard drive chain Standard sprocket sizes Drive chain lubricant designed specifically for O-ring chains. If not available, use SAE 80 or 90 gear oil. 25 to 35 mm (1.0 to 1.4 in) DID 520V0 or RK 520KHO CTX700A No. of links 114 CTX700D No. of links 112 Engine sprocket 16T Rear wheel sprocket CTX700A 43T CTX700D 39T Specifications ■ Bulbs Headlight Brake/Tail light Front turn signal lights Rear turn signal lights License plate light 12V-60/55W LED 12V-21/5W × 2 12V-21W × 2 12V-5W ■ Fuses Main fuse Other fuses 130 30A 30A, 15A, 7.5A ■ Torque Specifications Engine oil drain bolt Engine oil filter Front wheel axle shaft Front wheel brake caliper mounting bolts Front wheel axle pinch bolt Muffler end cover bolts Rear wheel axle nut Drive chain adjusting lock nuts Parking brake caliper mounting bolts 30 N·m (3.1 kgf·m, 22 lbf·ft) 26 N·m (2.7 kgf·m, 19 lbf·ft) 74 N·m (7.5 kgf·m, 55 lbf·ft) 30 N·m (3.1 kgf·m, 22 lbf·ft) 22 N·m (2.2 kgf·m, 16 lbf·ft) 10 N·m (1.0 kgf·m, 7 lbf·ft) 98 N·m (10.0 kgf·m, 72 lbf·ft) 21 N·m (2.1 kgf·m, 15 lbf·ft) 31 N·m (3.2 kgf·m, 23 lbf·ft) 14 CTX700-32MJF8000.book 131 ページ 2013年5月9日 木曜日 午後9時59分 Index Index A ABS (Anti-lock Brake System) Indicator ............................................ 28, 98 Accessories................................................. 16 AT Mode.................................. 25, 37, 39, 40 AT/MT Switch ............................................ 33 D D Mode .................................... 25, 37, 39, 40 Digital Clock Adjustment.......................... 27 Drive Chain ................................................ 82 Dual Clutch Transmission.......................... 37 Index B Battery ................................................. 54, 69 Brake Light Switch .................................... 93 Brakes Fluid................................................... 57, 78 Pad Wear ................................................. 79 Parking Brake........................................... 80 Braking ...................................................... 12 Bulb Brake/Tail Light ...................................... 111 Front Turn Signal.................................... 111 Headlight ............................................... 110 License Plate Light.................................. 112 Rear Turn Signal..................................... 111 C Caring for Your Motorcycle.................... 122 Catalytic Converter.................................. 121 Centre Lower Cowl.................................... 66 Clutch System ............................................ 87 Colour Label .............................................. 53 Coolant ................................................ 58, 76 Crankcase Breather ................................... 91 E Electrical Trouble..................................... 109 131 14 CTX700-32MJF8000.book 132 ページ 2013年5月9日 Engine Number.................................................. 127 Oil ...................................................... 56, 70 Oil Filter.................................................... 73 Overheats................................................. 96 Starting .................................................... 34 Stop Switch .......................... 30, 33, 34, 117 Stopping ................................................ 117 Environment ............................................ 126 Equipment Owner’s Manual............................... 45, 119 Tool Kit .............................................. 45, 63 Index 132 F Flooded Engine ......................................... 34 Frame Number......................................... 127 Fuel Gauge ................................................ 23, 24 Recommended ......................................... 42 Remaining .......................................... 23, 24 Tank Capacity........................................... 42 Fuels Containing Alcohol........................ 120 Fuses................................................... 55, 113 木曜日 午後9時59分 G Gasoline......................................................42 Gear Position Indicator..............................25 H Hazard Switch ......................................30, 32 Headlight Aim............................................92 Headlight Dimmer Switch ...................30, 32 Helmet Holder ...........................................46 High Beam Indicator..................................29 High Coolant Temperature Indicator .............................................28, 96 HISS Indicator.......................................29, 95 Horn Button .........................................30, 33 I Ignition Cut-off System Banking Sensor .......................................119 Side Stand ................................................81 Ignition key ..............................................116 Ignition Switch...............................31, 33, 34 Image Labels ................................................6 Indicators....................................................28 14 CTX700-32MJF8000.book 133 ページ 2013年5月9日 Instruments ............................................... 22 L Labels........................................................... 6 Load Limits ................................................ 17 Loading Guidelines ................................... 17 Low Oil Pressure Indicator.................. 28, 97 N N-D Switch................................................. 33 Neutral Indicator....................................... 29 午後9時59分 O Odometer .................................... 23, 24, 117 Oil Engine................................................ 56, 70 Overheating............................................... 96 P Parking....................................................... 14 Parking Brake ...................................... 32, 80 Parking Brake Indicator ............................ 29 Parts Location ............................................ 18 Passing light control switch ................ 30, 32 PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) .... 28, 97 Protective Apparel .................................... 11 Index M Maintenance Fundamentals .......................................... 52 Importance .............................................. 48 Safety ...................................................... 48 Schedule .................................................. 49 Maximum Weight Limit............................ 17 Modifications ............................................ 16 MT Mode ................................. 25, 37, 39, 40 木曜日 R Recommended Coolant .................................................... 58 Fuel .......................................................... 42 Oil ............................................................ 56 Refuelling .................................................. 42 133 14 CTX700-32MJF8000.book 134 ページ 2013年5月9日 Removal Battery ..................................................... 69 Centre Lower Cowl .................................. 66 Clip .......................................................... 68 Right Under Cowl..................................... 67 Right Under Cowl Lid ............................... 65 Seat.......................................................... 64 Repair Kit ................................................. 101 Riding Precautions .................................... 12 Right Under Cowl...................................... 67 Right Under Cowl Lid................................ 65 Index 134 S S Mode ..................................... 25, 37, 39, 40 Safety Precautions..................................... 11 Seat ............................................................ 64 Serial Numbers ........................................ 127 Shelter Pocket............................................ 44 Shift Switch................................................ 32 Shifting Gears ............................................ 36 Side Stand .................................................. 81 Side Stand Ignition Cut-off System .......... 81 Specifications........................................... 128 木曜日 午後9時59分 Speedometer........................................23, 24 Start Button ...................................30, 33, 34 Starting the Engine ...................................34 Steering Lock .......................................31, 33 Stopping Engine ......................................117 Storage Equipment ................................................44 Owner’s Manual ...............................45, 119 Shelter Pocket...........................................44 Tool Kit.....................................................45 Storing Your Motorcycle .........................125 Switches......................................................30 T Tachometer ..........................................23, 24 Throttle ......................................................90 Tool kit .................................................45, 63 Transporting Your Motorcycle................125 Tripmeter .....................................23, 24, 117 Troubleshooting ........................................94 Turn signal indicators ................................29 Tyres Air Pressure...............................................59 14 CTX700-32MJF8000.book 135 ページ 2013年5月9日 木曜日 午後9時59分 Puncture ................................................ 101 Replacing ......................................... 59, 101 W Warning Indicators On ............................. 97 Washing Your Motorcycle...................... 122 Weight Limit ............................................. 17 Wheels Front removal......................................... 102 Rear removal.......................................... 105 Index 135 14 CTX700-32MJF8000.book 136 ページ 2013年5月9日 木曜日 午後9時59分 14 CTX700-32MJF8000.book 137 ページ 2013年5月9日 木曜日 午後9時59分 14 CTX700-32MJF8000.book 138 ページ 2013年5月9日 木曜日 午後9時59分