14 TRX420FA1 FA2-32HR3B000.book 2 ページ Honda TRX420FA1 4 × 4 TRX420FA2 4 × 4 with Power Steering OWNER’S MANUAL (Original instructions) 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 3 ページ 2013年9月6日 金曜日 午後1時57分 Introduction Congratulations on choosing your Honda ATV. Introduction When you own a Honda, you’re part of a worldwide family of satisfied customers — people who appreciate Honda’s reputation for building quality into every product. Your Honda was designed as a recreational ATV for off-road use by one rider only. This ATV is ATV Type I category G. We recommend you to receive the ATV Pre-Delivery Checklist from your dealer. Before riding, take time to get acquainted with your ATV and how it works. To protect your investment, we urge you to take responsibility for keeping your ATV well maintained. Scheduled service is a must, of course. But it’s just as important to observe the break-in guidelines, and perform all pre-ride and other periodic checks detailed in this manual. We also recommend that you read and understand this owner’s manual before you ride. It’s full of facts, instructions, safety information, and helpful tips. To make it easy to use, the manual contains a detailed list of topics at the beginning of each section and an index at the back of the book. As you read this manual, you will find information that is preceded by a NOTICE symbol. This information is intended to help you avoid damage to your Honda, other property, or the environment. Whenever you ride, tread lightly. By staying on established trails and riding only in approved areas, you help protect the environment and keep off-road riding areas open for the future. Introduction 14 TRX420FA1 FA2-32HR3B000.book 4 ページ 2013年9月6日 金曜日 午後1時57分 Introduction Before riding the ATV, you must evaluate yourself with the below evaluation sheet, in the items that match your ATV. First checks • Can the person reach the footrests • Does he have a good lateral vision (make the panoramic test) First exercises • Can move the ATV without using it, walking beside it • Can park the ATV, activate the parking brake Familiarity with the controls, correct use • Can set correctly rear view mirrors • Can use the lights • Can use the clutch • Can use the gearbox • Can use the accelerator • Can use the braking systems First manoeuvres (make 2 at reduced speed, among which one slalom) • Can use the clutch in conjunction with the brake • Balance satisfactory • Direction of vision satisfactory • Driving technique satisfactory • Gear selection technique satisfactory Emergency manoeuvres the maximum speed of the vehicle • Front and rear brakes satisfactory • Direction of vision satisfactory • Position of the ATV satisfactory On a slope Can perform a U turn • Can drive down the slope Good distribution of the body weight Introduction 14 TRX420FA1 FA2-32HR3B000.book 5 ページ 2013年9月6日 金曜日 午後1時57分 Introduction Awareness of special situations • Impact of meteorological conditions • Wary of driving errors or dangerous behaviour putting the immediate safety of the rider or other persons at risk Behaviour satisfactory during use in normal situations (after explanations by the supervisor) • Cornering using body weight • Driving down a slope • Climbing slopes • Driving down a slope • Crossing a slope horizontally • Driving on rough terrain • Skidding and wheel spin If you have any questions, or if you ever need special service or repairs, remember that your dealer knows your ATV best and is dedicated to your complete satisfaction. Happy riding! • The following codes in this manual indicate each country. ED U European direct sales Australia New Zealand • The specifications may vary with each locale. • This vehicle pictured in this owner’s manual may not match your actual vehicle. Introduction 14 TRX420FA1 FA2-32HR3B000.book 6 ページ 2013年9月6日 金曜日 午後1時57分 A Few Words About Safety Your safety, and the safety of others, is very important. And operating this ATV safely is an important responsibility. A Few Words About Safety To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining an ATV. You must use your own good judgment. You will find important safety information in a variety of forms, including: Safety Labels — on the ATV. Safety Messages — preceded by a safety alert symbol 2 and one of three signal words: DANGER, WARNING, or CAUTION. A Few Words About Safety 14 TRX420FA1 FA2-32HR3B000.book 7 ページ 2013年9月6日 金曜日 午後1時57分 A Few Words About Safety These signal words mean: 3 DANGER 3 WARNING 3 CAUTION You WILL be KILLED or SERIOUSLY HURT if you don't follow instructions. You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. You CAN be HURT if you don’t follow instructions. Safety Headings — such as Important Safety Reminders or Important Safety Precautions. Safety Section — such as ATV Safety. Instructions — how to use this ATV correctly and safely. This entire manual is filled with important safety information — please read it carefully. A Few Words About Safety 14 TRX420FA1 FA2-32HR3B000.book 8 ページ 2013年9月6日 金曜日 午後1時57分 Contents These pages give an overview of the contents of your owner’s manual. The first page of each section lists the topics covered in that section. Contents ATV Safety ..................................................................................1 Important safety information you should know, plus a look at the safety related labels on your ATV. Instruments & Controls ............................................................15 The location and function of indicators and controls on your ATV and operating instructions for various controls and features. Before Riding ............................................................................55 The importance of wearing a helmet and other protective gear, how to make sure you and your ATV are ready to ride, and important information about loading. Basic Operation & Riding .........................................................71 How to start and stop the engine, shift gears, and brake. Also, riding precautions. Contents 14 TRX420FA1 FA2-32HR3B000.book 9 ページ 2013年9月6日 金曜日 午後1時57分 Contents Servicing Your Honda ............................................................109 Why your ATV needs regular maintenance, what you need to know before servicing your Honda, an owner maintenance schedule, and instructions for specific maintenance and adjustment items. Tips ..........................................................................................201 How to store and transport your ATV and how to be an environmentally responsible rider. Taking Care of the Unexpected.............................................211 What to do if you have a flat tyre, your engine won’t start, etc. Technical Information ............................................................237 ID numbers, technical specifications, and other technical facts. Index ........................................................................................248 Manufacturer and Authorised Representative for EU Market...258 Contents 14 TRX420FA1 FA2-32HR3B000.book 1 ページ 2013年9月6日 金曜日 午後1時57分 ATV Safety This section presents some of the most important information and recommendations to help you ride your ATV safely. Please take a few moments to read these pages. This section also includes information about the location of safety labels on your ATV. ATV Safety Important Safety Information........................................................ 2 Labels (ED type) ............................................................................ 5 Labels (U type) ............................................................................ 12 ATV Safety 1 14 TRX420FA1 FA2-32HR3B000.book 2 ページ 2013年9月6日 金曜日 午後1時57分 Important Safety Information Your ATV can provide many years of service and pleasure if you take responsibility for your own safety and understand the challenges you can meet while riding. There is much that you can do to protect yourself when you ride. You’ll find many helpful recommendations throughout this manual. The following are a few that we consider to be most important. Follow the Age Recommendation The minimum recommended age for this ATV model is 16. Children under age 16 should never operate this vehicle. Always Wear a Helmet It’s a proven fact: helmets significantly reduce the number and severity of head injuries. So always wear an approved motorcycle helmet. We also recommend that you wear eye protection, sturdy boots, gloves, and other protective gear (page 56). Never Carry a Passenger Your ATV is designed for one person only. There are no handholds, footrests, or seat for a second person, so never carry a passenger. A passenger could interfere with your ability to move around to maintain your balance and control of the ATV. 2 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 3 ページ 2013年9月6日 金曜日 午後1時57分 Important Safety Information Ride Off-road Only Your ATV is designed and manufactured for off-road use only. The tyres are not made for pavement, and the ATV does not have turn signals and other features required for use on public roads. If you need to cross a paved or public road, get off and walk your ATV across. Take Time to Learn & Practice Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight. Be Alert for Off-road Hazards The terrain can present a variety of challenges when you ride offroad. Continually ”read” the terrain for unexpected turns, drop-offs, rocks, ruts, and other hazards. Always keep your speed low enough to allow time to see and react to hazards. ATV Safety 3 14 TRX420FA1 FA2-32HR3B000.book 4 ページ 2013年9月6日 金曜日 午後1時57分 Important Safety Information Ride within Your Limits Pushing limits is another major cause of ATV crashes. Never ride beyond your personal abilities or faster than conditions warrant. Remember that alcohol, drugs, fatigue, and inattention can significantly reduce your ability to make good judgments and ride safely. Don’t Drink and Ride Alcohol and riding don’t mix. Even one drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. So don’t drink and ride, and don’t let your friends drink and ride either. Keep Your Honda in Safe Condition It’s important to keep your ATV properly maintained and in safe riding condition. Having a breakdown can be difficult, especially if you are stranded off-road far from your base. To help avoid problems, inspect your ATV before every ride and perform all recommended maintenance. 4 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 5 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) The following pages describe the label locations and their meanings. Some labels warn you of potential hazards that could cause serious injury. Others provide important safety information. Read this information carefully and don’t remove the labels, because it is important for the labels to be stored on the ATV. If a label comes off or becomes hard to read, contact your dealer for a replacement. There is a specific symbol on each label. The meanings of each symbol and label are as follows. Read instructions contained in Owner’s Manual carefully. Read instructions contained in Shop Manual carefully. In the interest of safety, take the ATV to be serviced only by your dealer. DANGER (with RED background) You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. WARNING (with ORANGE background) You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. CAUTION (with YELLOW background) You CAN be HURT if you don’t follow instructions. ATV Safety 5 14 TRX420FA1 FA2-32HR3B000.book 6 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) BATTERY LABEL DANGER • Keep flames and sparks away from the battery. The battery produces explosive gas that can cause an explosion. • Wear eye protection and rubber gloves when handling the battery to avoid risk of burns or loss of eyesight if exposed to battery electrolyte. • Do not allow children to handle the battery, under any circumstance. Ensure that anyone handling the battery has a proper understanding of the hazards and correct handling procedures involved. • Handle battery electrolyte with extreme care, as it contains dilute sulfuric acid. Exposure to eyes or skin can cause burns or loss of eyesight. • Read this manual carefully, and understand it before handling the battery. Failure to do so can cause personal injury and damage to the ATV. • Do not use the battery if the level of electrolyte is at or below the recommended level. Using the battery with low electrolyte can cause it to explode, causing serious injury. 6 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 7 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) RADIATOR CAP LABEL DANGER NEVER OPEN WHEN HOT. Hot coolant will scald you. Relief pressure valve begins to open at 1.1 kgf/cm2. GENERAL WARNING LABEL WARNING The improper operation of ATVs may result in severe injury or death. • Read the Owner’s Manual. • Follow all warnings and instructions. • Never use without proper training and instruction. While riding: • Never ride too fast for your skills or the conditions. • Always use proper riding techniques for hills, slopes, and rough terrain. • Use care when changing riding surfaces. ATVs handle differently on different surfaces, such as sand, dirt, or pavement. • Never carry a passenger, since it would affect balance and steering and may cause you to lose control. • Avoid operating on public roads, since a collision can occur with another vehicle. • Never ride after drinking alcohol or using drugs. • Always wear a helmet, eye protection, and protective gear. ATV Safety 7 14 TRX420FA1 FA2-32HR3B000.book 8 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) PASSENGER WARNING LABEL WARNING NEVER ride as a passenger. Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. AGE RECOMMENDATION WARNING LABEL WARNING Operating this ATV if you are under the age of 16 increases your chance of severe injury or death. NEVER operate this ATV if you are under age 16. TYRE & OVERLOAD WARNING LABEL WARNING Improper tyre pressure or overloading can cause loss of control. Loss of control can result in severe injury or death. • Cold tyre pressure: Front: Rear: 30 kPa (4.4 psi) 30 kPa (4.4 psi) • Maximum weight capacity: 187 kg (412 lb) FRONT CARRIER LABEL WARNING Overloading this ATV or carrying cargo improperly can change handling, stability and braking performance and can lead to an accident. Never exceed the maximum front cargo limit of: 30 kg (66 lb) Refer to instructions in the Owner’s Manual. 8 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 9 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) REAR CARRIER LABEL WARNING Overloading this ATV or carrying cargo improperly can change handling, stability and braking performance and can lead to an accident. Never exceed the maximum rear cargo limit (combined weight on the rear rack and in the storage area) of: 60 kg (133 lb) Refer to instructions in the Owner’s Manual. TRAILER HITCH LABEL WARNING Towing an improperly loaded trailer can cause loss of control. • Read towing instructions in Owner’s Manual. • Tow weight limit: 385 kg (850 lb) • Tongue weight: 14 kg (30 lb) 4WD BRAKING INFORMATION LABEL With four-wheel drive, operating any brake control cause braking at both the front and rear wheels. For detailed braking information, refer to the Owner’s Manual. CE MARK (TRX420FA1) Engine net power: 18.8 kW Machine mass: 285 kg (TRX420FA2) Engine net power: 18.8 kW Machine mass: 291 kg ATV Safety 9 14 TRX420FA1 FA2-32HR3B000.book 10 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) PASSENGER WARNING LABEL CE MARK (TRX420FA1) (TRX420FA2) BATTERY LABEL RADIATOR CAP LABEL FRONT CARRIER LABEL 10 ATV Safety TYRE & OVERLOAD WARNING LABEL 14 TRX420FA1 FA2-32HR3B000.book 11 ページ 2013年9月6日 金曜日 午後1時57分 Labels (ED type) AGE RECOMMENDATION WARNING LABEL GENERAL WARNING LABEL 4WD BRAKING INFORMATION LABEL TRAILER HITCH LABEL REAR CARRIER LABEL ATV Safety 11 14 TRX420FA1 FA2-32HR3B000.book 12 ページ 2013年9月6日 金曜日 午後1時57分 Labels (U type) Your ATV comes with several labels containing important safety information. Anyone who rides the vehicle should read and understand this information before riding. The labels should be considered permanent parts of the vehicle. If a label comes off or becomes hard to read, contact your dealer for replacements. 12 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 13 ページ 2013年9月6日 金曜日 午後1時57分 Labels (U type) ATV Safety 13 14 TRX420FA1 FA2-32HR3B000.book 14 ページ 2013年9月6日 金曜日 午後1時57分 Labels (U type) NEVER ride as a passenger. Passengers can cause a loss of control, resulting in SEVERE INJURY or DEATH. 14 ATV Safety 14 TRX420FA1 FA2-32HR3B000.book 15 ページ 2013年9月6日 金曜日 午後1時57分 Instruments & Controls This section shows the location of all indicators and controls you would normally use before or while riding your ATV. Instruments & Controls The items listed on this page are described in this section. Instructions for other components are presented in other sections of this manual where they will be most useful. Operation Component Locations ................................................ 17 Indicators & Displays ................................................................... 20 Multi-function Display.............................................................. 26 Speed and Mileage Unit Changing........................................... 29 4WD Indicator ......................................................................... 29 Gear Position Indicator............................................................. 30 Fuel Gauge .............................................................................. 31 Digital Clock ............................................................................ 33 Odometer................................................................................ 34 Tripmeter................................................................................. 34 Coolant Temperature Gauge ................................................... 35 Hourmeter............................................................................... 37 Maintenance Tripmeter & Maintenance Hourmeter.................. 38 (cont’d) Instruments & Controls 15 14 TRX420FA1 FA2-32HR3B000.book 16 ページ 2013年9月6日 金曜日 午後1時57分 Instruments & Controls Controls & Features .................................................................... 40 Ignition Switch......................................................................... 40 2WD/4WD Select Lever............................................................ 41 Start Button............................................................................. 42 Engine Stop Switch.................................................................. 42 Headlight Switch ..................................................................... 43 Headlight Dimmer Switch ........................................................ 43 Horn Button ............................................................................ 43 Throttle Lever .......................................................................... 44 Drive Mode Select Switch ........................................................ 45 Gearshift Switch ...................................................................... 46 Reverse Selector Knob ............................................................. 47 Front Brake Lever..................................................................... 48 Rear Brake Lever/Parking Brake Lever ....................................... 48 Rear Brake Pedal...................................................................... 48 Parking Brake .......................................................................... 49 Flag Pole Bracket ..................................................................... 50 Trailer Hitch ............................................................................. 51 Storage Compartment ............................................................. 52 PS (Electric Power Steering) (TRX420FA2 only) ......................... 53 16 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 17 ページ 2013年9月6日 金曜日 午後1時57分 Operation Component Locations reverse selector knob rear brake lever/ parking brake lever headlight dimmer switch parking brake lock lever headlight switch front brake lever horn button gearshift switches start button engine stop switch throttle lever drive mode select switch ignition switch 2WD/4WD select lever Instruments & Controls 17 14 TRX420FA1 FA2-32HR3B000.book 18 ページ 2013年9月6日 金曜日 午後1時57分 Operation Component Locations rear cargo rack front cargo rack rear brake pedal 18 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 19 ページ 2013年9月6日 金曜日 午後1時57分 Operation Component Locations flag pole bracket trailer hitch storage compartment Instruments & Controls 19 14 TRX420FA1 FA2-32HR3B000.book 20 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays The indicators and displays on your ATV keep you informed, alert you to possible problems, and make your riding safer and more enjoyable. Refer to the indicators frequently. Their functions are described on the following pages. (3) (2) (1) (4) (7) (1) neutral indicator (2) reverse indicator (3) PGM-FI indicator (4) high coolant temperature indicator 20 Instruments & Controls (6) (5) (5) PS (Electric Power Steering) indicator (TRX420FA2 only) (6) multi-function display (7) mode button 14 TRX420FA1 FA2-32HR3B000.book 21 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Lamp Check Initial lamp check: The indicators come on for a few seconds and then go off when you turn the ignition switch ON (q). The high coolant temperature indicator and PGM-FI indicator will temporarily come back on for a few seconds and then go off after initial lamp check. TRX420FA2 only The PS (Electric Power Steering) indicator come back on and remains on until the engine is started after initial lamp check. These indicators are identified in the table on page 23 with the words: Lamp Check. When applicable, the reverse or neutral indicators come back on and remain on until you shift out of reverse or neutral after initial lamp check. If one of these indicators does not come on when it should, have your dealer check for problems. Instruments & Controls 21 14 TRX420FA1 FA2-32HR3B000.book 22 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Display Check When the ignition switch is turned on, the multi-function display (1) will temporarily show all the modes and digital segments and initial message. So you can make sure the liquid crystal display is functioning properly. The displays are identified in the table on page 24 with the words: Display Check. If any part of these displays does not come on when it should, have your dealer check for problems. (1) (1) multi-function display 22 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 23 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays 1 Neutral indicator 2 Reverse indicator 3 PGM-FI indicator 4 High coolant temperature indicator 5 PS (Electric Power Steering) indicator (TRX420FA2 only) Lights when the transmission is in neutral. Lamp Check. Lights when the transmission is in reverse. Lamp Check. Lights when there is any abnormality in the PGM-FI (Programmed Fuel Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned on. If the indicator comes on at any other time, reduce speed and take your vehicle to your dealer as soon as possible. Lamp Check. Lights when coolant temperature is high enough to adversely affect the service life of the engine. If the high coolant temperature indicator comes on while you are riding, immediately bring the vehicle to a stop, turn the engine off and let it cool. See page 225. Lamp Check. Lights when there is an abnormality in the PS (Electric Power Steering) system. See page 53. Lamp Check. Instruments & Controls 23 14 TRX420FA1 FA2-32HR3B000.book 24 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays 6 Multi-function display 4WD indicator Gear position indicator Speedometer Fuel gauge Digital clock Odometer Tripmeter Coolant temperature gauge Hourmeter Maintenance minder indicator Maintenance tripmeter Maintenance hourmeter 24 Instruments & Controls The display includes the following functions. Display Check. Shows when the 4WD drive mode engages (page 29). Shows the gear position (page 30). Shows riding speed (page 26). Shows approximate fuel supply available (page 31). Shows the time (hours and minutes) (page 33). Shows accumulated mileage (page 34). Shows mileage per trip (page 34). Shows approximate coolant temperature (page 35). Shows hours and tenths of hours of engine operation (page 37). Shows when specified maintenance interval is reached (page 38). Inform when the mileage or operating hours on your ATV approaches and passes the interval specified on the maintenance schedule (page 38). 14 TRX420FA1 FA2-32HR3B000.book 25 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays 7 Mode button Selects display in the lower parts of multi-function display (page 26). This button also used to change the speed and mileage unit (page 29), adjusts the clock (page 33) and resets tripmeter, maintenance tripmeter and maintenance hourmeter (page 38). Instruments & Controls 25 14 TRX420FA1 FA2-32HR3B000.book 26 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Multi-function Display The multi-function display (1) includes the following functions: 4WD indicator Odometer Gear position indicator Tripmeter Maintenance minder Coolant temperature gauge Hourmeter indicator Speedometer Maintenance tripmeter Fuel gauge Maintenance hourmeter Digital clock (4) (3) (5) (2) (1) (6) (1) multi-function display (5) maintenance minder (2) 4WD indicator indicator (3) gear position indicator (6) fuel gauge/digital clock/ odometer/tripmeter/coolant (4) speedometer temperature gauge/ hourmeter/maintenance tripmeter/maintenance hourmeter 26 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 27 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Each time you press the mode button, mode will change as shown in the illustration. Fuel gauge (page 31) Digital clock (page 33) Hourmeter (page 37) Odometer (page 34) Tripmeter (page 34) Maintenance tripmeter (page 38) Coolant temperature gauge (page 35) Maintenance hourmeter (page 38) When ATV is moving When ATV is not moving Instruments & Controls 27 14 TRX420FA1 FA2-32HR3B000.book 28 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays If there is a fuel warning with your ATV, the display will automatically change to the fuel gauge. If you try to change the display back to ordinary display, it will automatically return to the fuel gauge. If there is a coolant temperature warning with your ATV, the display will automatically change to the coolant temperature gauge. If you try to change the display back to ordinary display, it will automatically return to the coolant temperature gauge. 28 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 29 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Speed and Mileage Unit Changing The speedometer, odometer, tripmeter and maintenance tripmeter show in either “MPH” and “MILE” or “KM/H” and “KM”. To change the speed and mileage unit, press and hold the mode button (1) for more than 5 seconds in odometer (page 34) with the ATV stopped. (1) (1) mode button 4WD Indicator The 4WD indicator (1) appears when the 4WD mode engages (page 41). (1) (1) 4WD indicator Instruments & Controls 29 14 TRX420FA1 FA2-32HR3B000.book 30 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Gear Position Indicator The gear position indicator (1) shows the gear position when the ignition switch is in the ON (q) position. Automatic shift (AUTO) mode: The indicator displays N for neutral, R for reverse, and D for drive. Manual shift (ESP) mode: The indicator displays N for neutral, R for reverse, and 1 – 5 for the five forward gears. “–” will be displayed on the gear position indicator when the transmission is not shifted into gear properly. Before riding, check that the gear position is properly displayed on the gear position indicator. If the gear position indicator shows “–” or blinks, turn the ignition switch to the OFF (w) position, and then turn it back to the ON (q) position again. If the gear position indicator shows “–”, rock the vehicle back and forth and make sure the gear position indicator is displayed properly and then if the gear position indicator still shows “–” or blinks, see your dealer. If the “–” on the gear position indicator is blinking, see your dealer. (1) (1) gear position indicator 30 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 31 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Fuel Gauge The fuel gauge (1) shows the approximate fuel supply available with fuel mark (2). The fuel tank capacity is: 14.7 ℓ (3.88 US gal, 3.23 lmp gal) (2) (1) (2) fuel mark (1) fuel gauge Regardless of what mode the display is in, when the fuel level reaches only 1st segment (3), the display will automatically switch to the fuel gauge display. You should refuel as soon as possible. The amount of fuel remaining when there is only 1st segment is approximately: 6.9 ℓ (1.82 US gal, 1.52 lmp gal) (3) (3) 1st segment Instruments & Controls 31 14 TRX420FA1 FA2-32HR3B000.book 32 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays When the fuel gauge show E _ _ _ _ _ F (4) and LO FUEL (5) blink 3 times alternately and fuel mark blinks, you should refill the tank as soon as possible. (The fuel mark blinks except the fuel gauge display) The amount of fuel reserve approximately: 4.9 ℓ (1.29 US gal, 1.08 lmp gal) (4) (5) (4) E _ _ _ _ _ F (5) LO FUEL Fuel gauge failure: When the fuel gauge show E - - - - - F (6) will blink, when the fuel gauge function fails. See your dealer. (The fuel mark disappears except the fuel gauge display) (6) (6) E - - - - - F 32 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 33 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Digital Clock The digital clock (1) displays hours and minutes with the clock mark (2), when the ignition switch is ON (q). To adjust the time, proceed as follows: 1. Turn the ignition switch ON (q) to display the clock (page 27). 2. Press and hold the mode button (3) until the display start blinking. 3. To advance the display 1 minute at a time, press and release the mode button for 0.5 seconds. Press and hold the mode button for more 0.5 seconds the display will begin advancing fast. 4. Release the mode button when the display reaches the desired time. 5. To set the clock, press and release the mode button for less than 0.5 seconds. The clock can be set by turning the ignition switch off and then on. (2) (3) (1) digital clock (2) clock mark (1) (3) mode button After the battery is reconnected (page 193), check the clock. Readjust the clock if necessary. Instruments & Controls 33 14 TRX420FA1 FA2-32HR3B000.book 34 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Odometer The odometer (1) registers total distance traveled in mileage while the ignition is ON (q) with the ODO display (2). The odometer locks at 999999 when the read-out exceeds 999999. (2) (1) (1) odometer (2) ODO display Tripmeter The tripmeter (1) shows mileage per trip with the TRIP display (2), while the ignition is ON (q) since you last reset the tripmeter. The tripmeter returns to 0.0 when the read-out exceeds 999.9. To reset the tripmeter to zero, press the mode button (3) and hold it in for at least 2 seconds in the tripmeter mode. (2) (1) (3) (1) tripmeter (2) TRIP display 34 Instruments & Controls (3) mode button 14 TRX420FA1 FA2-32HR3B000.book 35 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Coolant Temperature Gauge The coolant temperature gauge (1) with the coolant temperature mark (2) shows the coolant temperature. When coolant temperature is low, the coolant temperature gauge will display “Lo”. (3) (1) (1) coolant temperature gauge (2) coolant temperature mark (2) (3) high coolant temperature indicator If all sections of the coolant temperature gauge and high coolant temperature indicator are on (automatically appears in the display) while you are riding, immediately stop the vehicle, turn the engine off and check the coolant reserve tank level. See page 146. Instruments & Controls 35 14 TRX420FA1 FA2-32HR3B000.book 36 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays NOTICE Continuing to ride with an overheated engine can cause serious engine damage. Coolant temperature gauge failure: If the coolant temperature system has an error, the coolant temperature gauge (1) will flash and preferentially appear in the display, and/or high coolant temperature indicator (3) will turn on. If this occurs, see your dealer as soon as possible. (3) (1) (1) coolant temperature gauge 36 Instruments & Controls (3) high coolant temperature indicator 14 TRX420FA1 FA2-32HR3B000.book 37 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Hourmeter The hourmeter (1) shows accumulated hours while the ignition switch is ON (q) with the hourmeter mark (2). The hourmeter provides accurate service period information for initial and regular maintenance. The hourmeter locks at 99999.9 when the read-out exceeds 99999.9. (2) (1) (1) hourmeter (2) hourmeter mark Instruments & Controls 37 14 TRX420FA1 FA2-32HR3B000.book 38 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Maintenance Tripmeter & Maintenance Hourmeter The maintenance tripmeter (1), the maintenance hourmeter (2) and maintenance minder indicator (3) inform you when the mileage or operating hours on your ATV approaches and passes the maintenance interval specified on the maintenance schedule (page 116). (3) (3) (2) (1) (1) maintenance tripmeter (2) maintenance hourmeter (3) maintenance minder indicator The maintenance tripmeter, or the maintenance hourmeter and maintenance minder indicator will blink, when they reach their setting values. (3) (3) (1) (2) 38 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 39 ページ 2013年9月6日 金曜日 午後1時57分 Indicators & Displays Reset the meters after each scheduled maintenance. To reset the maintenance tripmeter and the maintenance hourmeter, press and hold the mode button and turn the ignition switch to ON ( I ). Continue to hold the mode button, the maintenance minder indicator will light up, and after 2 seconds will flash twice, the maintenance minder indicator is reset. Also the maintenance tripmeter and maintenance hourmeter will reset. Maintenance Minder Indicators: Initial Maintenance Appears at 150 km (100 miles) or 20 operating hours, whichever comes first. Regular Maintenance Interval 1 Appears 1,000 km (600 miles) or 100 operating hours after the Initial Maintenance or Regular Maintenance Interval 2 is performed and maintenance minder is reset, whichever comes first in the maintenance schedule. Regular Maintenance Interval 2 Appears 1,000 km (600 miles) or 100 operating hours after Regular Maintenance Interval 1 is performed and maintenance minder is reset, whichever comes first in the maintenance schedule. If the maintenance is done before the setting interval, be sure to reset the meters after the maintenance. Instruments & Controls 39 14 TRX420FA1 FA2-32HR3B000.book 40 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Ignition Switch The ignition switch (1) is used for starting and stopping the engine (page 79). Insert the key and turn it to the right for the ON (q) position. The ignition switch is also used to reset the maintenance tripmeter and the maintenance hourmeter (page 38). Key Position ON (q) OFF (w) Function Electrical circuits on. No electrical circuits function. CENTRE OF HANDLEBAR OFF ON (1) (1) ignition switch 40 Instruments & Controls q ON w OFF 14 TRX420FA1 FA2-32HR3B000.book 41 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features 2WD/4WD Select Lever Your ATV is equipped with a 2WD/4WD select lever (1), which permits a choice between the “2WD” and “4WD” drive modes. Select a drive mode that’s suitable for your riding. Keep both hands on the handlebar while machine is in motion and come to a complete stop before using the 2WD/4WD select lever. The 2WD/4WD select lever is located on the left side of the fuel tank. To select the drive mode, shift the 2WD/4WD select lever to the desired position. After using the 2WD/4WD select lever, the mode may not mechanically engage until forward motion begins. To check your present drive mode, look at the 4WD indicator (2). 2WD mode: the 4WD indicator goes off when the 2WD mode engages. 4WD mode: the 4WD indicator goes on when the 4WD mode engages. 4WD MODE 4WD MODE (2) (1) 2WD MODE (1) 2WD/4WD select lever 2WD MODE (2) 4WD indicator Instruments & Controls 41 14 TRX420FA1 FA2-32HR3B000.book 42 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features o Start Button LEFT HANDLEBAR (2) (1) (1) start button (2) engine stop switch o START r OFF e RUN The start button (1) is used for starting the engine. Pushing the button in starts the engine. See Starting Procedure, page 81. When the start button is pushed, the starter motor will crank the engine. The starter motor will not operate if the engine stop switch is in the OFF (r) position when the start button is pushed. Engine Stop Switch e r The engine stop switch (2) is used to stop the engine in an emergency. To operate, slide the switch to the OFF (r) position. The switch must be in the RUN (e) position to start the engine, and it should normally remain in the RUN (e) position even when the engine is OFF. If your ATV is stopped with the ignition switch ON (q) and the engine stop switch OFF (r), the battery will discharge. Turn the ignition switch OFF (w) to prevent battery discharge. 42 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 43 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features y Headlight Switch LEFT HANDLEBAR t (2) (3) (1) headlight switch (1) y ON t OFF u HI i LO (2) headlight dimmer switch (3) horn button The headlight switch (1) is used to turn the headlight ON (y) or OFF (t). To operate, turn the switch to ON (y) or OFF (t). u i Headlight Dimmer Switch The headlight dimmer switch (2) is used to change between the high and low beams of the headlight. To operate, turn the switch to HI (u) for high beam, LO (i) for low beam. Horn Button Press the horn button (3) to sound the horn. Instruments & Controls 43 14 TRX420FA1 FA2-32HR3B000.book 44 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Throttle Lever RIGHT HANDLEBAR (A) (1) (1) throttle lever (A) to open the throttle The throttle controls engine rpm (speed). To increase engine rpm, press the throttle lever (1) with your thumb. To reduce engine rpm, release pressure on the throttle lever. The throttle will automatically return to the closed position (engine idle) when you remove your thumb. 44 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 45 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Drive Mode Select Switch The drive mode select switch (1) has two positions, AUTO (automatic shift mode) and ESP (manual shift mode). See Shifting Gears page 84. RIGHT HANDLEBAR (1) (1) drive mode select switch Instruments & Controls 45 14 TRX420FA1 FA2-32HR3B000.book 46 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Gearshift Switch Automatic shift (AUTO) mode: These gearshift switches [upshift switch (1) and downshift switch (2)] are used to select the drive (D), neutral (N) and reverse (R). See Shifting Gears, page 84 and Riding in Reverse, page 90. Manual shift (ESP) mode: These gearshift switches are used to select the next higher or lower gear in the transmission. To operate, press the upshift switch (1) to engage the next higher gear or press the downshift switch (2) to engage the next lower gear. See Shifting Gears, page 84 and Riding in Reverse, page 90. LEFT HANDLEBAR (1) (2) (1) upshift switch (2) downshift switch 46 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 47 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Reverse Selector Knob The reverse selector knob (1), located on the rear brake lever/parking brake lever (2), is used to shift into reverse. To operate, with your ATV stopped and the transmission in neutral (make sure the neutral indicator lights and the gear position indicator shows “N”), push in the knob, squeeze the rear brake lever/parking brake lever, then press the downshift switch (3) once. See Riding in Reverse, page 90. LEFT HANDLEBAR (1) (2) (3) (1) reverse selector knob (2) rear brake lever/parking brake lever (3) downshift switch Instruments & Controls 47 14 TRX420FA1 FA2-32HR3B000.book 48 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Front Brake Lever The front brake lever is used to slow or stop your ATV. To operate, pull the lever. For information on braking techniques, see page 92. Rear Brake Lever/Parking Brake Lever The rear brake lever/parking brake lever is used to slow or stop your ATV. To operate, pull the lever. For information on braking techniques, see page 92. Rear Brake Pedal The rear brake pedal is used to slow or stop your ATV. To operate, depress the pedal. For information on braking techniques, see page 92. 48 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 49 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Parking Brake LEFT HANDLEBAR (1) (A) (2) (1) lock lever (A) to lock (2) rear brake lever/parking brake lever The lock lever (1) on the rear brake lever/parking brake lever (2) allows it to be used as a parking brake. To operate, first squeeze the rear brake lever/parking brake lever using your left hand and then lock it with the lock lever using your right hand. See Parking page 107. The brake lights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch to OFF (w) to avoid discharging the battery. Instruments & Controls 49 14 TRX420FA1 FA2-32HR3B000.book 50 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Flag Pole Bracket RIGHT REAR (1) (1) flag pole bracket Flag poles are optional equipment available from your dealer. To mount a pole in the bracket (1), follow the instructions that come with the flag pole kit. Flag poles are required in some riding areas. Check local regulations before riding. 50 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 51 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Trailer Hitch REAR (2) (1) (1) trailer hitch (2) ball The trailer hitch (1) is located on the rear axle housing. To use the hitch, you’ll need a proper size ball (2) as specified by the trailer manufacturer. To attach the ball and properly hook up a trailer, follow the trailer manufacturer’s instructions, For load limits and operational guidelines, see page 65. Instruments & Controls 51 14 TRX420FA1 FA2-32HR3B000.book 52 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features Storage Compartment The storage compartment (1) is located below the rear cargo rack (2). To open the compartment, unhook the rubber strap (3). Be careful not to flood this area when washing your ATV. REAR (2) (3) (1) (1) storage compartment (2) rear cargo rack (3) rubber strap 52 Instruments & Controls 14 TRX420FA1 FA2-32HR3B000.book 53 ページ 2013年9月6日 金曜日 午後1時57分 Controls & Features PS (Electric Power Steering) (TRX420FA2 only) This ATV is equipped with an electronically controlled, electricpower-assisted steering system. While the engine is running, the PS (Electric Power Steering) system provides power from the electric motor, which helps you to turn the ATV’s handlebar more easily. The PS system on this ATV utilizes an overheat protection feature to prevent damage to system components. In certain extended, repetitive high-load situations, the system will reduce or even disable power steering assist. The steering will perform as a normal non-PS system during this brief period. After cooling down, it will then return to normal PS operation. The PS indicator should light when the ignition switch is turned ON (q) and remain on until the engine is started. The PS indicator also lights when there is any abnormality in the PS system. If this occurs, the electric power assist for turning will not be available, but the manual steering system will perform as usual. If the PS indicator lights at any time while riding, reduce speed and take your ATV to your dealer as soon as possible. Continuing to ride with a PS system problem can cause system damage. Do not modify your Electric Power Steering system. In case of a malfunction, take your ATV to your dealer. Instruments & Controls 53 14 TRX420FA1 FA2-32HR3B000.book 54 ページ 54 Instruments & Controls 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 55 ページ 2013年9月6日 金曜日 午後1時57分 Before Riding Before each ride, you need to make sure you and your Honda are both ready to ride. To help get you prepared, this section discusses how to evaluate your riding readiness, what items you should check on your ATV, and adjustments to make for your comfort, convenience, or safety. This section also includes important information about loading. Before Riding Are You Ready to Ride? .............................................................. 56 Protective Apparel ................................................................... 56 Rider Training .......................................................................... 58 Age Recommendation ............................................................. 59 No Passengers ......................................................................... 59 No Alcohol or Drugs ................................................................ 60 Is Your ATV Ready to Ride? ........................................................ 61 Pre-ride Inspection ................................................................... 61 Load Limits & Guidelines............................................................. 65 Loading ................................................................................... 65 Load Limits .............................................................................. 66 Loading Guidelines .................................................................. 67 Accessories & Modifications........................................................ 68 Accessories .............................................................................. 68 Modifications........................................................................... 69 Before Riding 55 14 TRX420FA1 FA2-32HR3B000.book 56 ページ 2013年9月6日 金曜日 午後1時57分 Are You Ready to Ride? Before you ride your ATV for the first time, we urge you to: • Read this owner’s manual and the labels on your ATV carefully. • Make sure you understand all the safety messages. • Know how to operate all the controls. Before each ride, be sure: • You feel well and are in good physical and mental condition. • You are wearing an approved motorcycle helmet (with chin strap tightened securely), eye protection, and other protective clothing. • You don’t have any alcohol or drugs in your system. Protective Apparel For your safety, we strongly recommend that you always wear an approved motorcycle helmet, eye protection, boots, gloves, trousers, and a long-sleeved shirt or jacket whenever you ride. Although complete protection is not possible, wearing proper gear can reduce the chance of injury when you ride. Following are suggestions to help you choose the proper gear. Helmet and Eye Protection Your helmet is your most important piece of riding gear because it offers the best protection against head injuries. A helmet should fit your head comfortably and securely. 56 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 57 ページ 2013年9月6日 金曜日 午後1時57分 Are You Ready to Ride? An open-face helmet offers some protection, but a full-face helmet offers more. Always wear a face shield or goggles to protect your eyes and help your vision. WARNING 3 WARNING Operating this ATV without wearing an approved motorcycle helmet, eye protection, and protective clothing could increase your chances of severe injury or death in the event of an accident. Always wear an approved motorcycle helmet that fits properly and wear eye protection (goggles or face shield), gloves, boots, longsleeved shirt or jacket and trousers. Additional Riding Gear In addition to a helmet and eye protection, we also recommend: • Sturdy off-road motorcycle boots to help protect your feet, ankles, and lower legs. • Off-road motorcycle gloves to help protect your hands. • Riding trousers with knee and hip pads, a riding jersey with padded elbows, and a chest/shoulder protector. Before Riding 57 14 TRX420FA1 FA2-32HR3B000.book 58 ページ 2013年9月6日 金曜日 午後1時57分 Are You Ready to Ride? Rider Training Developing your riding skills is an on-going process. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice riding the ATV in a safe area to build your skills. Do not ride in rough terrain until you get accustomed to the ATV’s controls, and feel comfortable with its size and weight. WARNING 3 WARNING Operating this ATV without proper instruction could increase your risk of an accident which could lead to serious injury or death. Beginning and inexperienced operators should complete the certified training course offered by Honda. They should then regularly practice the skills learned in the course and the operating techniques described in the owner’s manual. 58 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 59 ページ 2013年9月6日 金曜日 午後1時57分 Are You Ready to Ride? Age Recommendation The minimum recommended age for this ATV model is 16. For safety, never let children under 16 years old operate this vehicle. WARNING 3 WARNING A child using an ATV that is not recommended for their age could lose vehicle control while riding, resulting in severe injury or death. A child under 16 should never operate an ATV with engine size greater than 90cc. No Passengers This ATV is designed as an operator-only vehicle. The long seat is designed to allow the rider to change body position, not for carrying a passenger. Never let a passenger ride on the seat or on the front or rear cargo racks. WARNING 3 WARNING Carrying a passenger on this ATV greatly reduces your ability to balance and control this ATV and could cause a crash and you or your passenger could be injured or killed. Never carry a passenger on this ATV. Before Riding 59 14 TRX420FA1 FA2-32HR3B000.book 60 ページ 2013年9月6日 金曜日 午後1時57分 Are You Ready to Ride? No Alcohol or Drugs Alcohol, drugs and ATVs don’t mix. Even a small amount of alcohol can impair your ability to operate an ATV safely. Likewise, drugs — even if prescribed by a physician — can be dangerous while operating an ATV. Consult your doctor to be sure it is safe to operate a vehicle after taking medication. WARNING 3 WARNING Operating this ATV after consuming alcohol or drugs can seriously affect your judgement, cause you to react more slowly, affect your balance and perception, and result in serious injury or death. Never consume alcohol or drugs before or while operating this ATV. 60 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 61 ページ 2013年9月6日 金曜日 午後1時57分 Is Your ATV Ready to Ride? Before each ride, it’s important to inspect your ATV and make sure any problem you find is corrected. A pre-ride inspection is a must, not only for safety, but because having a breakdown, or even a flat tyre, can be a major inconvenience. If your ATV has overturned or been involved in a collision, do not ride the vehicle until it has been inspected by your dealer. There may be damage or other problems you cannot see. WARNING 3 WARNING Improperly maintaining this ATV or failing to correct a problem before riding can cause a crash in which you can be seriously hurt or killed. Always perform a pre-ride inspection before every ride and correct any problems. Pre-ride Inspection Check the following items before you get on the ATV: Engine Oil Check the level and add oil if needed (page 135). Check for leaks. Radiator Coolant Check the coolant level and add coolant if needed (page 146). Check for leaks. (cont’d) Before Riding 61 14 TRX420FA1 FA2-32HR3B000.book 62 ページ 2013年9月6日 金曜日 午後1時57分 Is Your ATV Ready to Ride? Fuel Check the level and add fuel (page 130) if needed. Also make sure the fuel fill cap is securely fastened. Check for leaks. Tyres Use a gauge to check the air pressure. Adjust if needed. Also look for signs of damage or excessive wear (page 180). Drivetrain Boots Check for damage (page 189). Guards Check for damage or looseness (page 187). Nuts & Bolts Check the wheels to see that the axle nuts are tightened. Use a wrench to make sure all accessible nuts, bolts, and fasteners are tight. Underbody & Exhaust Check for, and remove, any dirt, vegetation System or other debris that could be a fire hazard or interfere with the proper operation of the vehicle. Air Cleaner Housing Drain Tube Check for deposits in the drain tube. If necessary, clean the tube (page 157) and check the air cleaner housing. Leaks, Loose Parts Walk around your ATV and look for anything that appears unusual, such as a leak or loose cable. Cable Check the cable housings for wear. Check the fittings for looseness. Replace or tighten as needed. Lights Make sure the headlight, brake light and taillight are working properly. 62 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 63 ページ 2013年9月6日 金曜日 午後1時57分 Is Your ATV Ready to Ride? If you are carrying cargo, also check the following: Loading Limits Make sure you do not exceed the load limits (page 66). Cargo Check that all cargo is secure. Check these items after you get on the ATV: Throttle Check the freeplay and adjust if needed. Press the throttle to make sure it moves smoothly without sticking, and snaps shut automatically when it is released, in all steering positions (page 158). Brakes Squeeze the front and rear brake levers and step on the rear brake pedal to check that the controls operate normally. Check for proper freeplay (page 173,175). Make sure there is no brake fluid leakage (page 170). Reverse Assist Lever Check the freeplay and adjust if needed (page 160). Make sure the lever operates smoothly without sticking. Before Riding 63 14 TRX420FA1 FA2-32HR3B000.book 64 ページ 2013年9月6日 金曜日 午後1時57分 Is Your ATV Ready to Ride? Headlight and Check for proper function (page 43). Headlight Dimmer Switch Engine Stop Switch Check for proper function (page 42). Steering Check that the wheels turn properly as you steer the handlebar. Move the handlebar right and left and check that there is no excessive backlash. Remember, be sure to take care of any problem you find, or have your dealer correct it before you ride. 64 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 65 ページ 2013年9月6日 金曜日 午後1時57分 Load Limits & Guidelines Your Honda was designed as a rider-only ATV. It was not designed to carry a passenger. It can carry cargo on the cargo racks, however, carrying cargo anywhere else or carrying a passenger could interfere with your balance and control of the ATV. In addition, exceeding the weight limits or carrying an unbalanced load can seriously affect your ATV’s handling, braking and stability. Adding accessories or making modifications that change this ATV’s design and performance can also make it unsafe. Also, the weight of any accessories will reduce the maximum load the ATV can carry. More specific information on load limits, accessories, and modifications follows. Loading How much weight you put on your ATV, and how you load it, are important to your safety. If you decide to carry cargo, you should be aware of the following information. WARNING 3 WARNING Overloading, improper loading, or carrying a passenger can cause a crash and you can be seriously hurt or killed. Follow all load limits and other loading guidelines in this manual. Before Riding 65 14 TRX420FA1 FA2-32HR3B000.book 66 ページ 2013年9月6日 金曜日 午後1時57分 Load Limits & Guidelines Load Limits Following are the load limits for your ATV: There are limits to how much weight can be carried on your ATV and be pulled in a trailer. The following load limits apply to standard equipment only. Modifying your ATV, using non-standard equipment, or riding on terrain that is not flat and smooth could further reduce these limits. maximum weight capacity ED type: 187 kg (412 lb) U type: 220 kg (485 lb) (includes the weight of the rider, all cargo, and accessories.) front cargo rack weight limit = 30 kg (66 lb) rear cargo rack weight limit = 60 kg (133 lb) tow weight limit = 385 kg (850 lb) (Combined weight of the trailer and all cargo in the trailer) tongue weight (Weight on the trailer tongue) = 14 kg (30 lb) recommended tongue and rear cargo weight = 60 kg (133 lb) maximum (Combined weight on the trailer tongue and on the rear cargo rack) Tongue weight can be measured with an ordinary bathroom scale. Place the scale under the tongue, using either a tongue jack or other support to keep the trailer level. The weight of added accessories will reduce the maximum cargo weight you can carry. 66 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 67 ページ 2013年9月6日 金曜日 午後1時57分 Load Limits & Guidelines Loading Guidelines Carrying cargo or pulling a trailer will affect how your ATV handles and greatly reduce its ability in accelerating, braking and making turns and other maneuvers. Be sure to observe the weight limits and follow these guidelines: • Check that the tyres are properly inflated. • Do not place cargo anywhere on the ATV other than on the front and rear racks. Otherwise, operating stability may be adversely affected. • Never ride with a passenger on the front or rear cargo racks. The ATV is not designed to carry a passenger. • Use the trailer hitch to tow another vehicle or trailer. Do not tow by tying a rope or cable to the rear rack. • Load cargo on the rear rack as far forward as possible. Make sure cargo on the front rack does not interfere with handlebar movement. • Do not allow cargo to extend beyond the edges of either the front or rear racks. • Make sure all cargo is secured before riding. • Balance cargo weight evenly on both sides. • Never exceed the maximum weight limit. • When towing a trailer, take care to maintain balance and stability. Distribute cargo between the front and rear of the trailer to obtain the recommended tongue weight. • Allow extra room for starting, stopping and turning whenever you carry cargo or pull a trailer. • Avoid riding on steep slopes when carrying cargo or pulling a trailer. • Never cross a slope when towing a trailer. Before Riding 67 14 TRX420FA1 FA2-32HR3B000.book 68 ページ 2013年9月6日 金曜日 午後1時57分 Accessories & Modifications Modifying your ATV or using non-Honda accessories can make your ATV unsafe. Before you consider making any modifications or adding an accessory, be sure to read the following information. WARNING 3 WARNING Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding accessories and modifications. Accessories We strongly recommend that you use only Honda Genuine Accessories that have been specifically designed and tested for your ATV. Because Honda cannot test all other accessories, you must be personally responsible for proper selection, installation, and use of non-Honda accessories. Check with your dealer for assistance and always follow these guidelines: • Make sure the accessory does not obscure any lights, reduce ground clearance, limit suspension travel or steering travel, or interfere with operating any controls. • Make sure the accessory does not interfere with your ability to shift body position on the seat or operate hand and foot controls. • Do not add any electrical equipment that will exceed the vehicle’s electrical system capacity (page 243). A blown fuse can cause a loss of lights or engine power (page 227). 68 Before Riding 14 TRX420FA1 FA2-32HR3B000.book 69 ページ 2013年9月6日 金曜日 午後1時57分 Accessories & Modifications Modifications We strongly advise you not to remove any original equipment or modify your ATV in any way that would change its design or operation. Such changes could seriously impair your ATV’s handling, stability, and braking, making it unsafe to ride. Because safety, vehicle movement, and clearance must be taken into consideration, you must consult your tyre maker or Honda dealer before changing your tyre model type. Removing or modifying your lights, exhaust system, emission control system, or other equipment can also make your ATV illegal. Before Riding 69 14 TRX420FA1 FA2-32HR3B000.book 70 Before Riding 70 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 71 ページ 2013年9月6日 金曜日 午後1時57分 Basic Operation & Riding This section gives basic riding instructions, including how to start and stop your engine, and how to use the throttle and brakes. It also provides important information on riding with cargo. Basic Operation & Riding To protect your new engine and enjoy optimum performance and service life, refer to Break-in Guidelines (page 246). Safe Riding Precautions .............................................................. 73 Off-road Use Only.................................................................... 73 Keep Hands and Feet on Controls............................................ 74 Riding Position & Safety Equipment ......................................... 75 Moving the ATV without Starting the Engine ........................... 76 Control Speed ......................................................................... 77 Use Care on Unfamiliar or Rough Terrain ................................. 77 Do Not Perform Stunts............................................................. 78 Starting & Stopping the Engine................................................... 79 Preparation.............................................................................. 80 Starting Procedure ................................................................... 81 Flooded Engine........................................................................ 81 Bank Angle Sensor Ignition Cut-off System .............................. 82 Stalled Engine.......................................................................... 82 How to Stop the Engine........................................................... 83 Shifting Gears............................................................................. 84 Riding in Reverse ........................................................................ 90 (cont’d) Basic Operation & Riding 71 14 TRX420FA1 FA2-32HR3B000.book 72 ページ 2013年9月6日 金曜日 午後1時57分 Basic Operation & Riding Braking....................................................................................... 92 Riding Your ATV......................................................................... 94 Making Turns .......................................................................... 94 Skidding or Sliding................................................................... 96 Riding Up Hills ......................................................................... 97 Riding Down Hills .................................................................. 101 Crossing or Turning on Hills or Slopes .................................... 102 Riding Over Obstacles ............................................................ 104 Riding Through Water ........................................................... 105 Parking ..................................................................................... 107 72 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 73 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions Before riding your ATV for the first time, please review the ATV Safety section beginning on page 1, and the Before Riding section beginning on page 55. Even if you have ridden other ATVs, take time to become familiar with how this ATV works and handles. Practice in a safe area until you build your skills and get accustomed to the ATV’s size and weight. Off-road Use Only Your ATV and its tyres are designed and manufactured for off-road use only, not for pavement. Riding on pavement can affect handling and control. You should not ride your ATV on pavement. WARNING 3 WARNING Operating this ATV on paved surfaces may seriously affect handling and control of the ATV, and may cause the vehicle to go out of control. Never operate the ATV on any paved surfaces, including sidewalks, driveways, parking lots and streets. When riding off-road, also remember to always obey local off-road riding laws and regulations. Obtain permission to ride on private property. Avoid posted areas and obey “no trespassing” signs. (cont’d) Basic Operation & Riding 73 14 TRX420FA1 FA2-32HR3B000.book 74 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions You should never ride your ATV on public streets, roads or highways, even if they are not paved. Drivers of street vehicles may have difficulty seeing and avoiding you, which could lead to a collision. In many states it is illegal to operate ATVs on public streets, roads and highways. WARNING 3 WARNING Operating this ATV on public streets, roads or highways could cause you to collide with another vehicle. Never operate this ATV on any public street, road or highway, even a dirt or gravel one. Keep Hands and Feet on Controls Always keep both hands on the handlebars and both feet on the footpegs when riding your ATV. This is important to maintain your balance and to control the vehicle. Removing even one hand from the handlebars or one foot from the footpegs can reduce your ability to control the ATV or could cause you to lose your balance and fall off the ATV. WARNING 3 WARNING Removing hands from handlebars or feet from footpegs during operation can reduce your ability to control the ATV or could cause you to lose your balance and fall off of the ATV. Always keep both hands on the handlebars and both feet on the footpegs of your ATV during operation. 74 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 75 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions Riding Position & Safety Equipment Sit on the vehicle as shown below, keeping your hands on the handlebars and feet on the footpegs. Helmet and eye protection Off-road motorcycle gloves Long-sleeved apparel and trousers Off-road motorcycle boots Basic Operation & Riding 75 14 TRX420FA1 FA2-32HR3B000.book 76 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions Moving the ATV without Starting the Engine When you need to move the ATV without starting the engine follow the below steps. (When the ATV has stalled or starts to roll backwards, see page 100) Be sure your legs are clear of the wheels. 1. After confirming that the engine is off, stand beside the ATV so you can reach the rear brake lever with your left hand. 2. Be sure your legs are clear of the wheels. 3. Check your footing. 4. Slowly and carefully push the ATV, and use the rear brake lever to control speed as necessary. 76 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 77 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions Control Speed Riding at excessive speed increases the chance of a crash. In choosing a proper speed, you need to consider the capability of your vehicle, the terrain, visibility and other operating conditions, plus your own skills and experience. WARNING 3 WARNING Operating this ATV at excessive speeds increases your chances of losing control of the ATV, which can result in an accident. Always go at a speed that is proper for your vehicle, the terrain, visibility and other operating conditions, and your experience. Use Care on Unfamiliar or Rough Terrain Before riding in a new area, always check the terrain thoroughly. Don’t ride fast on unfamiliar terrain or when visibility is limited. (It’s sometimes difficult to see obstructions like hidden rocks, bumps, or holes in time to react.) WARNING 3 WARNING Failure to use extra care when operating this ATV on unfamiliar terrain could result in the ATV overturning or going out of control. Go slowly and be extra careful when operating on unfamiliar terrain. Always be alert to changing terrain conditions when operating the ATV. Basic Operation & Riding 77 14 TRX420FA1 FA2-32HR3B000.book 78 ページ 2013年9月6日 金曜日 午後1時57分 Safe Riding Precautions Never ride past the limit of visibility. Maintain a safe distance between your ATV and other off-road vehicles. Always exercise caution, and use extra care on rough, slippery and loose terrain. WARNING 3 WARNING Failure to use extra care when operating on excessively rough, slippery or loose terrain could cause loss of traction or vehicle control, which could result in an accident, including an overturn. Do not operate on excessively rough, slippery or loose terrain until you have learned and practiced the skills necessary to control the ATV on such terrain. Always be especially cautious on these kinds of terrain. Do Not Perform Stunts You should always operate your ATV in a safe and reasonable manner. When riding, always keep all four wheels on the ground. WARNING 3 WARNING Attempting wheelies, jumps, and other stunts increases the chance of an accident, including an overturn. Never attempt stunts, such as wheelies or jumps. Don’t try to show off. 78 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 79 ページ 2013年9月6日 金曜日 午後1時57分 Starting & Stopping the Engine Always follow the proper starting procedure described below. For your safety, avoid starting or operating the engine in an enclosed area such as a garage. Your ATV’s exhaust contains poisonous carbon monoxide gas which can collect rapidly in an enclosed area and cause illness or death. If you turn the ignition switch to the OFF (w) position while in reverse, the transmission will automatically return to neutral (N) when the ignition switch is turned to the ON (q) position. The starter motor will operate when the transmission is in neutral or the front brake lever is pulled in. Basic Operation & Riding 79 14 TRX420FA1 FA2-32HR3B000.book 80 ページ 2013年9月6日 金曜日 午後1時57分 Starting & Stopping the Engine Preparation (2) (1) (3) (1) ignition switch (3) engine stop switch (2) neutral indicator 1. Before starting, select a level surface and lock the parking brake (page 49). 2. Turn the ignition switch (1) to ON (q). Confirm the following: • The transmission is in neutral, the neutral indicator (2) is ON and the gear position indicator shows “N”. • The engine stop switch (3) is set to RUN (e). 80 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 81 ページ 2013年9月6日 金曜日 午後1時57分 Starting & Stopping the Engine Starting Procedure This ATV is fuel-injected with an automatic choke. Follow the procedure indicated below. Any Air Temperature • Press the start button with the throttle completely closed. The engine will not start if the throttle is fully open (because the electronic control module cuts off the fuel supply). Snapping the throttle or fast idling for more than 5 minutes may cause exhaust pipe and muffler discolourations. Flooded Engine If the engine fails to start after repeated attempts, it may be flooded with excess fuel. To clear a flooded engine: 1. Leave the engine stop switch set to RUN (e). 2. Open the throttle fully. 3. Press the start button for 5 seconds. 4. Follow the normal starting procedure. 5. If the engine starts, then open the throttle slightly if idling is unstable. If the engine does not start, wait 10 seconds, then follow steps 1 – 4 again. If the engine still won’t start, refer to If Your Engine Quits or Won’t Start, page 214. Basic Operation & Riding 81 14 TRX420FA1 FA2-32HR3B000.book 82 ページ 2013年9月6日 金曜日 午後1時57分 Starting & Stopping the Engine Bank Angle Sensor Ignition Cut-off System Your vehicle’s banking (lean angle) sensor system is designed to automatically stop the engine if the vehicle is overturned. Before restarting the engine, you must turn the ignition switch to the OFF (w) position and then back to ON (q). The engine will not restart until you perform this procedure. Stalled Engine You can restart the engine while the vehicle is stopped by squeezing the front brake lever and pressing the start button. Do not press the throttle lever while starting in gear. Your ATV is equipped with a start inhibitor system that will cut off the ignition if the throttle is open while attempting to start in gear. Once you have started the engine, release the front brake lever, then apply throttle gradually. 82 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 83 ページ 2013年9月6日 金曜日 午後1時57分 Starting & Stopping the Engine How to Stop the Engine Normal Engine Stop To stop the engine, make sure the transmission is in neutral by checking that the neutral indicator light is on, then turn the ignition switch to OFF (w). The engine stop switch should normally remain in the RUN (e) position even when the engine is OFF. If your ATV is stopped with the engine stop switch OFF (r) and the ignition switch ON (q), the battery will discharge. Emergency Engine Stop To stop the engine in an emergency, use the engine stop switch. To operate, slide the switch to the OFF (r) position. Basic Operation & Riding 83 14 TRX420FA1 FA2-32HR3B000.book 84 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears Your ATV has three shift modes: neutral (N), drive (D), and reverse (R). You can select the desired shift mode with the gearshift switches. Neutral (N) Use neutral when you start the engine, or if it is necessary to stop briefly with the engine idling. The gear position indicator shows “N”. Drive (D) Use this position for normal riding. The following two modes can be selected in the drive (D) position; automatic drive (AUTO) mode and manual drive (ESP) mode. You can select the desired mode with the drive mode select switch (page 45). Automatic shift (AUTO) mode: Use this mode for everyday riding. The transmission automatically shifts to keep the engine at the best speed for riding condition. The gear position indicator shows “D”. Manual shift (ESP) mode: In this mode, you can shift gears much like a manual transmission, but without operating a clutch. You can select five forward shift positions by operating the gearshift switches; 1, 2, 3, 4, and 5. The gear position indicator shows the selected position. When you tow a trailer, select the 1st shift position for proper performance. Reverse (R) Use this position to ride in reverse. The gear position indicator shows “R”. 84 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 85 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears Shift mode (D/N/R) select Two gearshift switches are located next to the left handlebar grip: Upshift ( ) and downshift ( ). To select the shift mode, bring the ATV to complete stop, confirm the transmission is in neutral and press the shift switch to select shift mode. To select drive shift mode (D), press the upshift switch (1) once. • When you select automatic shift (AUTO) mode with the drive mode select switch, the gear position indicator shows “D”. • When you select manual shift (ESP) mode with the drive mode select switch, the gear position indicator shows the selected position. To select reverse shift (R), use the reverse selector knob and press the down shift switch (2) once. Riding in Reverse (page 90). LEFT HANDLEBAR (1) (2) automatic shift (AUTO) mode (1) upshift switch manual shift (ESP) mode (2) downshift switch Basic Operation & Riding 85 14 TRX420FA1 FA2-32HR3B000.book 86 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears Drive mode select (AUTO/ESP) The drive mode select switch (1) is located on the right handlebar. To select the drive mode, operate the drive mode select switch. With the throttle fully closed, the drive mode can be changed during running. RIGHT HANDLEBAR automatic shift (AUTO) manual shift (ESP) (1) (1) drive mode select switch Driving in automatic shift (AUTO) mode: After starting the engine and letting it warm up, follow these procedures: 1. With the transmission in neutral, release the parking brake, but continue squeezing the rear brake lever. 2. With the throttle closed, select the automatic shift (AUTO) mode and press the upshift switch once to shift into the auto shift mode (D). 3. The gear position indicator shows "D". 4. Release the rear brake lever and increase engine speed by gradually opening the throttle. 86 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 87 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears Driving in manual shift (ESP) mode: To upshift the transmission, press the upshift switch (1) once. To downshift the transmission, press the downshift switch (2) once. UPSHIFTING SEQUENCE (1) (A) DOWNSHIFTING SEQUENCE (2) (1) upshift switch (2) downshift switch (A) (A) press 1. With the transmission in neutral, release the parking brake, but continue squeezing the rear brake lever. 2. With the throttle closed, select the manual shift (ESP) mode and press the upshift switch ( ) once to shift into 1st gear. 3. The gear position indicator shows “1”. 4. Release the rear brake lever and increase engine speed by gradually opening the throttle. 5. When speed increases, release the throttle and upshift to 2nd position by pressing the upshift switch once. 6. Repeat this sequence to progressively upshift to 3rd, 4th and 5th (top) position. 7. To downshift, press the downshift switch ( ) once. Remember to close the throttle each time you shift to the next lower position. Basic Operation & Riding 87 14 TRX420FA1 FA2-32HR3B000.book 88 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears The transmission cannot be upshifted from neutral to 1st gear, Dmode, or R-mode when the engine speed is above 2,300 rpm or the ground speed is above 3 km/h (2 mph). The transmission cannot be downshifted from 1st gear, D-mode, or R-mode to neutral when the ground speed is above 1.5 km/h (1 mph) or engine speed is above 2,300 rpm. 5th to 4th automatically if less than 12 km/h (7 mph). 4th to 3rd automatically if less than 10 km/h (6 mph). 3rd to 2nd automatically if less than 8 km/h (5 mph). 2nd to 1st automatically if less than 5 km/h (3 mph). If the ATV is at a complete stop, 2nd gear, 3gear, 4th gear or 5th gear cannot be selected. If the electric shift system malfunctions, the transmission cannot be shifted by pressing the gearshift switches. See your dealer. (In an emergency, a gear may be selected manually so you may move the vehicle. See Emergency Gear Selection & Operation page 220). 88 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 89 ページ 2013年9月6日 金曜日 午後1時57分 Shifting Gears Learning when to shift gears in manual shift (ESP) mode comes with experience. Keep the following tips in mind: • As a general rule, shift while moving in a straight line. • Close the throttle completely before shifting. Improper shifting may damage the engine, transmission, and drivetrain. • Upshift to a higher gear or reduce throttle before engine rpm (speed) gets too high. Learn the relationship between engine sound and the normal shifting points. • Downshift to a lower gear before you feel the engine laboring (lugging) at low rpm. • Avoid downshifting to help slow your ATV when engine rpm is high. Downshifting when engine speed is near its allowable maximum may over-rev the engine and possibly cause damage. • To prevent transmission damage, do not coast or tow the ATV for long distances with the engine off. Recommended Shift Points Ride in the highest gear that lets the engine run and accelerate smoothly. This will give you good fuel economy and effective emissions control. Basic Operation & Riding 89 14 TRX420FA1 FA2-32HR3B000.book 90 ページ 2013年9月6日 金曜日 午後1時57分 Riding in Reverse If you need to ride in reverse, make sure the area behind you is clear and only operate the ATV at low speed. WARNING 3 WARNING Improperly operating in reverse could cause you to hit an obstacle or person behind you, resulting in serious injury. Make sure there are no obstacles or people behind you before selecting reverse gear. When it is safe to proceed, go slowly. 1. Bring the vehicle to a complete stop, then make sure the transmission is in neutral. 2. Be sure there are no obstacles or people in the way. 3. While pushing the reverse selector knob (1) in, squeeze the rear brake lever/parking brake lever (2), then press the downshift switch (3) once to shift into “R” (reverse) gear. LEFT HANDLEBAR (4) (1) (2) (3) (1) reverse selector knob (2) rear brake lever/ parking brake lever 90 Basic Operation & Riding (3) downshift switch (4) upshift switch 14 TRX420FA1 FA2-32HR3B000.book 91 ページ 2013年9月6日 金曜日 午後1時57分 Riding in Reverse NOTICE Your ATV may be equipped with a reverse speed limiter, which helps the vehicle to maintain a safe speed while riding in reverse gear. 4. The gear position indicator shows “R”. 5. Release the rear brake lever/parking brake lever. 6. Open the throttle gradually and ride slowly. Do not open the throttle suddenly or make abrupt turns. 7. To stop, close the throttle and gradually apply both the front and rear brakes. Do not abruptly apply the rear brake by itself. 8. To shift out of reverse and into neutral, press the upshift switch (4) once to shift into “N” (neutral) gear. The transmission cannot be shifted from neutral back into reverse when the engine speed is above 2,300 rpm or speed of your ATV is above 3 km/h (2 mph). The transmission cannot be shifted from reverse up to neutral when the engine speed is above 2,300 rpm or if the speed of your ATV is above 1.5 km/h (1 mph). If you turn the ignition switch to the OFF (w) position while in reverse, the transmission will automatically return to neutral (N) when the ignition switch is turned to the ON (q) position. WARNING 3 WARNING Applying only the rear brake abruptly when operating in reverse gear could cause the front wheels to lift off the ground and the ATV could overturn backwards. Carefully apply both the front and rear brakes when stopping in reverse gear. Basic Operation & Riding 91 14 TRX420FA1 FA2-32HR3B000.book 92 ページ 2013年9月6日 金曜日 午後1時57分 Braking Your ATV is equipped with disc brakes on both front wheels which are hydraulically activated by operating the right brake lever. A single drum brake on the rear axle housing is mechanically activated by depressing the brake pedal or operating the left brake lever. Although the front and rear brakes have separate controls, all four wheels are interconnected when your ATV is in the 4WD mode. So operating any brake control in the 4WD mode will cause braking at both the front and rear wheels. As a general rule, the front braking system provides about 70 percent of total stopping power. For full braking effectiveness, use both the pedal and lever simultaneously. Using both braking systems will stop your ATV faster with greater stability. To slow or stop, apply the brake lever and brake pedal smoothly, while downshifting to match your speed when your ATV is in the ESP mode. Gradually increase braking as you feel the brakes slowing your speed. The increase in engine compression from downshifting will help slow your vehicle when your ATV is in the ESP mode. Applying the brakes too hard may cause the wheels to lock and slide, reducing control of your ATV. If this happens, release the brake controls, steer straight ahead until you regain control, then reapply the brakes more gently. When possible, reduce your speed or complete braking before entering a turn. Avoid braking or closing the throttle quickly while turning. Either action may cause one or more wheels to slip and reduce your control of your ATV. 92 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 93 ページ 2013年9月6日 金曜日 午後1時57分 Braking Your ability to brake in a turn and to brake hard in an emergency situation are important riding skills. When descending a long, steep grade, use engine compression braking by downshifting (in the ESP mode), with intermittent use of both brakes. Continuous brake application can overheat the brakes and reduce their effectiveness. Riding with your foot resting on the brake pedal or your hands on the brake levers may overheat the brakes, reducing effectiveness. For information on how to apply the brakes in various riding situations, see the following section, Riding Your ATV. Basic Operation & Riding 93 14 TRX420FA1 FA2-32HR3B000.book 94 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Making Turns Learn how to turn your ATV properly. Practice the techniques outlined in this section on level ground and at low speeds until you are confident in making turns. WARNING 3 WARNING Turning improperly can make the ATV go out of control, causing a collision or overturn. • Always follow proper procedures for turning as described in this owner’s manual. • Practice turning at low speeds before attempting to turn at faster speeds. • Do not turn at excessive speeds. 94 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 95 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Lean your body to the inside of a turn and forward. To make a turn on level ground: Steer the handlebar and lean your body toward the inside of the turn. Leaning helps balance the vehicle, and it feels more comfortable. Leaning into a turn is an important technique to master in riding an ATV. To make a sharp turn at low speed: It helps to shift your body slightly forward on the seat, and lean inside, as you steer the handlebar. Shifting weight forward allows the rear wheels to turn easier, and it also improves front-wheel steering. To make a turn from a full stop: Apply the throttle gradually when you turn and start up at the same time. Remember to shift your body forward to make sharp low-speed turns and whenever you turn while accelerating from a full stop. Basic Operation & Riding 95 14 TRX420FA1 FA2-32HR3B000.book 96 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Skidding or Sliding The terrain surface can be a major factor affecting turns. Skidding during a turn is more likely to occur on slippery surfaces, such as snow, ice, mud and loose gravel. If you skid on ice, you may lose all directional control. To avoid skidding on slippery terrain, keep your speed low and ride with caution. WARNING 3 WARNING Skidding or sliding improperly may cause you to lose control of this ATV. You may also regain traction unexpectedly, which may cause the ATV to overturn. Learn to safely control skidding by practicing at low speeds and on level, smooth terrain. If your ATV skids sideways during a turn, steer in the direction of the skid. Avoid hard braking or accelerating until you have regained directional control. 96 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 97 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Riding Up Hills The ATV’s ability to safely climb hills largely depends on the rider’s skill and judgment. Begin by practicing on smooth, gentle slopes. As you gain experience, you’ll learn the hazards and your own limitations. You may then proceed to ride on more difficult terrain. However, you must be able to decide which hills or hazards might cause the ATV to overturn. Avoid excessively steep hills. WARNING 3 WARNING Operating on excessively steep hills can cause the vehicle to overturn more easily than operating on level surfaces or small hills. Never operate the ATV on hills too steep for the ATV or for your abilities. When climbing hills, you must shift weight toward the front wheels to help keep them on the ground. To do this, shift your body slightly forward on the seat and lean forward. For greater weight shift, move your body farther forward and lean forward. WARNING 3 WARNING Climbing hills improperly could cause loss of control or cause the ATV to overturn. Always follow proper procedures for climbing hills as described in this owner’s manual. Basic Operation & Riding 97 14 TRX420FA1 FA2-32HR3B000.book 98 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Shift weight forward when climbing hills. • Always check the terrain carefully before you start up any hill. • Never climb hills with excessively slippery or loose surfaces. • To climb a hill, take a running start in an appropriate gear and speed for the conditions. Maintain a steady speed as you ascend the hill. • Never open the throttle suddenly or make sudden gear changes. The ATV could flip over backward. • Never go over the top of any hill at high speed. An obstacle, a sharp drop, or another vehicle or person could be on the other side of the hill. 98 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 99 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Stalling the ATV and/or Rolling Backwards: If you incorrectly estimate climbing capability or terrain conditions, the ATV may not have enough power or traction to continue uphill. If this happens, the ATV can stall and/or roll backwards. WARNING 3 WARNING Stalling, rolling backwards or improperly dismounting while climbing a hill could result in the ATV overturning. Always follow proper procedures for climbing a hill as described in this owner’s manual. What to do if the ATV stalls or rolls backwards when climbing a hill: If you are about to lose all forward speed: 1. Using the front and rear brakes together, bring the ATV to a stop with the vehicle pointed straight uphill. 2. Get off the ATV while you continue holding the brakes. 3. Shift into neutral, set the parking brake and turn the engine off. 4. Then assess the situation. If the ATV starts rolling backwards before you begin braking: 1. Keep your weight uphill. 2. Carefully apply the front brakes first, then carefully apply the rear brake. Do not apply either brake abruptly if you are rolling backwards, or the vehicle may overturn. If the ATV continues sliding backwards: After you’ve applied the brakes, get off and away from the vehicle. Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels. Basic Operation & Riding 99 14 TRX420FA1 FA2-32HR3B000.book 100 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV What to do after the ATV has stalled or rolled backwards: If the hill is too steep or too slippery, or if you have any doubt whether you can safely walk the ATV back down the hill, leave the vehicle where it is and get help. If possible, block the wheels so the vehicle doesn’t roll backwards. If the hill is not too steep and you have good footing, you may be able to walk the ATV back down the hill. Make sure your intended path is clear in case you lose control of the ATV. Be sure your legs are clear of the wheels. Body position for backing down a hill. 1. Stand with your body facing downhill, beside the vehicle so you can reach the rear brake lever with your right hand. 2. Be sure your legs are clear of the wheels. Check your footing. 3. Slowly and carefully back the ATV down the hill using the rear brake lever to control speed. 4. If you lose control of the ATV, for your safety, get away from the vehicle. 100 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 101 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Riding Down Hills It’s usually advisable to descend hills with the ATV pointed straight downhill. Avoid angles that would cause the vehicle to lean sharply to one side. WARNING 3 WARNING Going down a hill improperly could cause loss of control or cause the ATV to overturn. Always follow proper procedures for going down hills as described in this owner’s manual. On downhills, shift your weight back. As you approach a downhill, stop and survey the terrain below. Never ride past the limit of your visibility. Never go down a hill at high speed. Basic Operation & Riding 101 14 TRX420FA1 FA2-32HR3B000.book 102 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV When you’ve selected a safe downhill path, shift into a lower gear (in the ESP mode), shift your weight back with your arms extended and braced against the handlebar, then go down slowly with the throttle closed. Use mainly the rear brake to control speed. Avoid using either the front brake or rear brake hard or abruptly when riding down hills. Remember that operating any brake control in the 4WD mode will cause braking at both the front and rear wheels. Remember, braking effectiveness is reduced on any hill with a loose surface. Crossing or Turning on Hills or Slopes Riding on hills or slopes is different from riding on level terrain. Be careful when riding on any hill. Make sure that you practice on gentle, smooth slopes before attempting to ride on steeper or more difficult terrain. WARNING 3 WARNING Improperly crossing hills or turning on hills could cause loss of control or cause the ATV to overturn. Always follow proper procedures for crossing or turning on slopes as described in this owner’s manual. Avoid crossing steep hills if possible. 102 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 103 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Crossing Hills or Slopes • To maintain balance and stability when riding across a slope, you need to shift weight toward the uphill side of the vehicle. To do this, move your body off the centre of the seat and lean toward the uphill side. • On a slippery or loose surface, you may also need to steer slightly uphill to maintain a straight course across the slope. • Avoid crossing hills that are excessively steep, slippery or rough. Shift weight uphill when crossing slopes. Making Turns on Slopes • Compared to riding on level ground, you may need to shift more weight and lean more when making turns on slopes. • Do not make turns on any slopes until you have first mastered the techniques for making turns on level terrain. Basic Operation & Riding 103 14 TRX420FA1 FA2-32HR3B000.book 104 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Riding Over Obstacles Before operating in a new area, check for obstacles. Watch out for bumps, rain ruts, potholes and other obstacles in the terrain. When you approach any obstacle, reduce your speed and be prepared to stop. Never try to ride over large obstacles, such as large rocks or fallen logs. WARNING 3 WARNING Improperly operating over obstacles could cause loss of control or a collision and could cause the ATV to overturn. When you go over obstacles, always follow proper procedures as described in this owner’s manual. 104 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 105 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV Riding Through Water Your ATV is designed to travel through water up to approximately 254 mm (10 inches) deep. Before crossing a stream, make sure the water is not too deep or flowing too fast. WARNING 3 WARNING The ATV tyres have some ability to float. Operating this ATV through deep or fastflowing water may cause a loss of traction and loss of control, which could lead to an accident. Never operate this ATV in fast-flowing water or in water deeper than that specified in this owner’s manual. NOTICE Water entering the muffler may damage the oxygen sensor and result in emissions control system malfunction. Have your ATV dealer inspect the oxygen sensor immediately after water enters the muffler. 1. Choose a path where both banks have gradual slopes. 2. Proceed through the water at a slow, steady speed. 3. Watch out for submerged obstacles and slippery rocks. 4. Avoid getting the spark plug or air cleaner wet, as this would cause the engine to stop. 5. After leaving the water, always test both the front and rear brakes. Basic Operation & Riding 105 14 TRX420FA1 FA2-32HR3B000.book 106 ページ 2013年9月6日 金曜日 午後1時57分 Riding Your ATV • Riding through water can make the brakes less effective than normal, and may reduce stopping ability. • If necessary, apply the brakes repeatedly until they dry out and operate normally. • If the brakes don’t regain effectiveness, stop your ATV and follow the procedures on page 179. 106 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 107 ページ 2013年9月6日 金曜日 午後1時57分 Parking Touching the brakes after long hours or heavy usage, can cause burn injuries. 1. Look for level parking area. Make sure the ground surface is firm. 2. After bringing your ATV to a stop, hold the brakes while you shift into neutral. 3. Set the parking brake. 4. Turn the ignition switch to OFF (w). If it is necessary to start the engine when your ATV in gear and is stopped on a grade, rock the vehicle back and forth to allow shifting the transmission into neutral. The brake lights are activated by applying the parking brake. When using the parking brake, be sure to turn the ignition switch to OFF (w) to avoid discharging the battery. Basic Operation & Riding 107 14 TRX420FA1 FA2-32HR3B000.book 108 ページ 2013年9月6日 金曜日 午後1時57分 Parking Parking on a Steep Incline or a Loose or Slippery Surface If you must park your ATV on a steep incline or loose or slippery surface, use the following procedure: 1. While holding the brakes, set the parking brake. 2. Turn the ignition switch to OFF (w) and release the brakes. 3. If the ATV begins to move, either while sitting on it or after you dismount, find a better parking location. 4. If rocks or other objects are available, you can block the wheels as shown for additional security. 108 Basic Operation & Riding 14 TRX420FA1 FA2-32HR3B000.book 109 ページ 2013年9月6日 金曜日 午後1時57分 Servicing Your Honda To help keep your ATV in good shape, this section includes a Maintenance Schedule for required service and step-by-step instructions for specific maintenance tasks. You’ll also find important safety precautions, information on fuels and oils, and tips for keeping your Honda looking good. Servicing Your Honda For information about replacing fuses, see page 227. Before You Service Your Honda The Importance of Maintenance ............................................... 111 Maintenance Safety.................................................................. 112 Important Safety Precautions ................................................. 113 Maintenance Schedule ............................................................. 114 Maintenance Record................................................................. 118 Service Preparations Maintenance Component Locations ......................................... 119 Tool Kit .................................................................................... 122 Owner’s Manual Storage .......................................................... 123 Seat Removal............................................................................ 124 Tank Cover Assembly Removal ................................................. 125 Rear Fender Cover Removal ...................................................... 127 Clip Removal ............................................................................ 128 (cont’d) Servicing Your Honda 109 14 TRX420FA1 FA2-32HR3B000.book 110 ページ 2013年9月6日 金曜日 午後1時57分 Servicing Your Honda Service Procedures Fluids & Filters Fuel .......................................................................................... 129 Engine Oil & Filter ..................................................................... 132 Rear Final Gear Oil .................................................................... 140 Front Final Gear Oil................................................................... 143 Coolant .................................................................................... 145 Air Cleaner ............................................................................... 152 Engine Throttle .................................................................................... 158 Reverse Lock System ................................................................. 160 Spark Plug ................................................................................ 161 Valves....................................................................................... 164 Spark Arrester .......................................................................... 165 Chassis Suspension ............................................................................... 166 Brakes ...................................................................................... 169 Wheels & Tyres......................................................................... 180 Guards ..................................................................................... 187 Drivetrain Boots ........................................................................ 189 Electrical Battery ..................................................................................... 191 Appearance Care...................................................................... 196 110 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 111 ページ 2013年9月6日 金曜日 午後1時57分 Before You Service Your Honda The Importance of Maintenance A well-maintained ATV is essential for safe, economical, and troublefree riding. It will also help reduce air pollution. Careful pre-ride inspections and good maintenance are especially important because your ATV is designed to be ridden over rough off-road terrain. To help you properly care for your ATV, this section of the manual provides a Maintenance Schedule. The service intervals in this schedule are based on average riding conditions. WARNING 3 WARNING Improperly maintaining this ATV or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual. Frequent servicing of the air cleaner is especially important to help you avoid a possible costly engine repair. If your ATV overturns or is involved in a crash, be sure your dealer inspects all major parts, even if you are able to make some repairs. Servicing Your Honda 111 14 TRX420FA1 FA2-32HR3B000.book 112 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Safety This section includes instructions on how to perform some important maintenance tasks. If you have basic mechanical skills, you can perform many of these tasks with the tools provided with your ATV. Other tasks that are more difficult and require special tools are best performed by professionals. Removing the wheels should normally be handled only by a Honda technician or other qualified mechanic. Instructions are included in this manual only to assist in emergency service. Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. WARNING 3 WARNING Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed. Always follow the procedures and precautions in this owner’s manual. 112 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 113 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Safety Important Safety Precautions • Make sure the engine is off before you begin any maintenance or repairs. This will help eliminate several potential hazards: Carbon monoxide poisoning from engine exhaust. Be sure there is adequate ventilation whenever you operate the engine. Burns from hot ATV parts. Allow the engine, muffler, brakes and other high-temperature parts to cool before servicing as you can get burned. Injury from moving parts. Do not run the engine unless instructed to do so. • Read the instructions before you begin, and make sure you have the tools and skills required. • To reduce the possibility of a fire or explosion, be careful when working around petrol. Use only non-flammable solvent, not petrol, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts. Remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new Honda Genuine Parts or other equivalents for repair and replacement. Servicing Your Honda 113 14 TRX420FA1 FA2-32HR3B000.book 114 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Schedule The required Maintenance Schedule that follows specifies how often you should have your ATV serviced, and what things need attention. It is essential to have your ATV serviced as scheduled to maintain safe, dependable performance and proper emission control. The service intervals in this Maintenance Schedule are based on average riding conditions. Some items will need more frequent service if you ride in unusually wet or dusty areas or at full throttle. Consult your dealer for recommendations applicable to your individual needs and use. Some items in the Maintenance Schedule can be performed with basic mechanical skills and hand tools. Procedures for these items are provided in this manual. Other items involve more extensive procedures and may require special training, tools, and equipment. We recommend that you have your dealer perform these tasks unless you have advanced mechanical skills and the required tools and equipment. Procedures for such items in this schedule are provided in an official Honda Shop Manual. If you do not feel capable of performing a given task or need assistance, remember that your Honda dealer knows your ATV best and is fully equipped to maintain and repair it. If you decide to do your own maintenance, use only Honda Genuine Parts or their equivalents for repair or replacement to ensure the best quality and reliability. Changing parts can affect your health and safety. We recommend that you consult your dealer if you do not have the proper equipment and experience to change parts on your own. 114 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 115 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Schedule Perform the pre-ride inspection (page 61) and owner maintenance on this section at each scheduled maintenance period. Each item on the maintenance schedule requires some mechanical knowledge. Certain items (particularly those marked * and **) may require more technical information and tools. Consult your dealer. * Should be serviced by your dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual. ** In the interest of safety, we recommend these items be serviced only by your dealer. Summary of Maintenance Schedule Notes & Procedures: NOTES: 1. Service more frequently when riding in dusty areas, sand or snow. 2. Service more frequently after riding in very wet or muddy conditions. 3. Replace every 2 years. Replacement requires mechanical skill. Servicing Your Honda 115 14 TRX420FA1 FA2-32HR3B000.book 116 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Schedule Maintenance Procedures: I: inspect and clean, adjust, lubricate, or replace, if necessary C: clean A: adjust L: lubricate R: replace FREQUENCY ITEMS * FUEL LINE * THROTTLE OPERATION AIR CLEANER AIR CLEANER HOUSING DRAIN TUBE SPARK PLUG * VALVE CLEARANCE ENGINE OIL WHICHEVER COMES FIRST NOTE * ENGINE IDLE SPEED RADIATOR COOLANT COOLING SYSTEM REGULAR MAINT. MAINT. INTERVAL 150 100 1 20 1000 600 6 100 2000 1200 12 200 I I C I NOTE 1 NOTE 2 C I NOTE 3 NOTE 2 I I I I I INITIAL= 150 km (100 mi), 20 operating hours or 1 month: R REGULAR= Every 1,000 km (600 mi), 100 operating hours or 12 months: R I I I I I I I ENGINE OIL FILTER * km mi MONTH HOURS INITIAL Refer to page — 158 152 157 161 164 132 137 — 145 — * Should be serviced by your dealer, unless you have the proper tools and service data, and is mechanically qualified. Refer to the official Honda Shop Manual. 116 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 117 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Schedule FREQUENCY ITEMS * * * * * * * * * ** ** ** ** WHICHEVER COMES FIRST NOTE DRIVETRAIN BOOTS FRONT/REAR FINAL GEAR OIL 2WD/4WD SELECT SYSTEM BRAKE FLUID NOTE 3 BRAKE SHOES WEAR NOTE 1, 2 BRAKE PADS WEAR NOTE 1, 2 BRAKE LIGHT SWITCH BRAKE SYSTEM REVERSE LOCK SYSTEM GUARDS SUSPENSION SPARK ARRESTER NUTS, BOLTS, FASTENERS WHEELS/TYRES TIE-ROD AND JOINT BOOTS STEERING SHAFT HOLDER BEARINGS STEERING SYSTEM km mi MONTH HOURS INITIAL REGULAR MAINT. MAINT. INTERVAL 150 100 1 20 1000 600 6 100 I (R: EVERY 2 YEARS) I I I I I I I I I I I I C I I 2000 1200 12 200 I I Refer to page I I I I I I I I I C I I I — 170 177 172 178 169 160 187 166 165 — 180 — I — I — 189 140,143 * Should be serviced by your dealer, unless you have the proper tools and service data, and is mechanically qualified. Refer to the official Honda Shop Manual. ** In the interest of safety, we recommend these items be serviced only by your dealer. Servicing Your Honda 117 14 TRX420FA1 FA2-32HR3B000.book 118 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Record Keeping an accurate maintenance record will help ensure that your ATV is properly maintained. Retain detailed receipts to verify the maintenance was performed. If the ATV is sold, these receipts should be transferred with the ATV to the new owner. Make sure whoever performs the maintenance completes this record. All scheduled maintenance, including the 150 km (100 mile) or 1 month or 20 hours initial maintenance, is considered a normal owner operating cost and will be charged for by your dealer. Use the space under Notes to record anything you want to remind yourself about or mention to your dealer. km (Miles) or ODO or months or hours HOUR 150 (100) or 1 or 20 1,000 (600) or 6 or 100 2,000 (1,200) or 12 or 200 3,000 (1,800) or 18 or 300 4,000 (2,400) or 24 or 400 5,000 (3,000) or 30 or 500 6,000 (3,600) or 36 or 600 7,000 (4,200) or 42 or 700 8,000 (4,800) or 48 or 800 118 Servicing Your Honda Date Performed By: Notes 14 TRX420FA1 FA2-32HR3B000.book 119 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Component Locations Service Preparations parking brake lock lever front brake fluid reservoir front brake lever reverse assist lever rear brake lever/ parking brake lever fuel fill cap throttle lever Servicing Your Honda 119 14 TRX420FA1 FA2-32HR3B000.book 120 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Component Locations air cleaner front suspension spring pre-load adjuster air cleaner housing drain tube rear brake light switch engine oil filter front brake caliper engine oil fill cap rear brake pedal front final gear oil fill cap front final gear oil drain bolt 120 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 121 ページ 2013年9月6日 金曜日 午後1時57分 Maintenance Component Locations owner’s manual air pressure gauge tool kit gear change tool battery fuse box main fuse 1 main fuse 2 PS fuse (TRX420FA2 only) coolant reserve tank engine oil dipstick rear brake panel spark plug engine oil drain bolt rear suspension spring pre-load adjuster spark arrester rear final gear oil fill cap rear final gear oil drain bolt Servicing Your Honda 121 14 TRX420FA1 FA2-32HR3B000.book 122 ページ 2013年9月6日 金曜日 午後1時57分 Tool Kit The tool kit (1) and the gear change tool (2) are stored under the rear fender cover (page 127). After using the tool kit or the gear change tool, be sure to use the rubber band (3) to fasten the tool kit and the gear change tool securely. The tools in the kit are sufficient to perform routine maintenance and simple repairs. Any extensive work requiring additional tools should be performed by your dealer. The tool kit includes the following items: * standard/Phillips screwdriver * screwdriver handle * 10 × 12 mm open end wrench * 14 × 17 mm open end wrench * spark plug wrench and handlebar * pliers * 5 mm Hex wrench * tool box (2) UNDER REAR FENDER COVER (1) (3) (1) tool kit (2) gear change tool 122 Servicing Your Honda (3) rubber band 14 TRX420FA1 FA2-32HR3B000.book 123 ページ 2013年9月6日 金曜日 午後1時57分 Owner’s Manual Storage Your ATV provides storage for the owner’s manual so you’ll have it with you for easy reference. Store your owner’s manual (1) in the plastic document bag underside of the rear fender cover (2). The owner’s manual and air pressure gauge (3) should be stored in the plastic bag (4) and fastened with the rubber band (5). To remove the rear fender cover, see page 127. Be careful not to flood this area when washing your ATV. REAR FENDER COVER UNDERSIDE (4) (5) (2) (3) (1) (1) owner’s manual (3) air pressure gauge (2) rear fender cover (4) plastic document bag (5) rubber band Servicing Your Honda 123 14 TRX420FA1 FA2-32HR3B000.book 124 ページ 2013年9月6日 金曜日 午後1時57分 Seat Removal Refer to Safety Precautions on page 113. The seat must be removed for the air cleaner, engine oil, engine oil filter, spark plug, battery and fuse maintenance and to remove the rear fender cover and tank cover assembly, to access the owner’s manual, air pressure gauge, gear change tool, and tool kit. (3) (2) (4) (1) seat latch (2) seat (3) front prongs (5) (1) (6) (4) hooks (5) studs (6) grommets Removal 1. Pull the seat latch (1) at the rear of the seat. 2. Slide the seat (2) back and lift it. Installation 1. Insert the front prongs (3) into the hooks (4) on the frame and press the studs (5) into the grommets (6). 2. Press down on the seat until locks. 124 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 125 ページ 2013年9月6日 金曜日 午後1時57分 Tank Cover Assembly Removal Refer to Safety Precautions on page 113. The tank cover assembly must be removed for the engine oil, engine oil filter and spark plug maintenance. RIGHT SIDE (1) (3) (1) (2) (2) (5) (1) prongs (2) grommets (3) tank cover assembly (2) (4) (4) tabs A (5) tabs B Removal 1. Remove the seat (page 124). 2. Remove the prongs (1) from the grommets (2). 3. Remove the tank cover assembly (3) by releasing the tabs A (4) and tabs B (5). Servicing Your Honda 125 14 TRX420FA1 FA2-32HR3B000.book 126 ページ 2013年9月6日 金曜日 午後1時57分 Tank Cover Assembly Removal LEFT SIDE (4) (1) (1) (2) (2) (5) (1) prongs (2) grommets (3) tank cover assembly (3) (2) (4) tabs A (5) tabs B Installation Install the parts in the reverse order of removal. Make sure that all prongs and tabs are installed securely in position. 126 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 127 ページ 2013年9月6日 金曜日 午後1時57分 Rear Fender Cover Removal Refer to Safety Precautions on page 113. The rear fender cover must be removed for battery, fuse maintenance and to access the owner’s manual, air pressure gauge, gear change tool and tool kit. (2) (5) (1) (4) (3) (1) rubber strap (2) prongs (3) grommets (4) rear fender cover (5) tabs Removal 1. Remove the seat (page 124). 2. Unhook the rubber strap (1) with opening the storage compartment (page 52). 3. Firmly pull the prongs (2) from their grommets (3). 4. Slide the rear fender cover (4) forward to disengage the tabs (5). 5. Remove the rear fender cover. Installation Install the parts in the reverse order of removal. Servicing Your Honda 127 14 TRX420FA1 FA2-32HR3B000.book 128 ページ 2013年9月6日 金曜日 Clip Removal Removal 1. Pull up the centre pin to release the lock. 2. Pull out the clip of the hole. 1. 2. Installation 1. Insert the clip into the hole. 2. Press down the centre pin securely to lock the clip. 1. 128 Servicing Your Honda 2. 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 129 ページ 2013年9月6日 金曜日 午後1時57分 Service&Procedures Fluids Filters Fuel Refer to Safety Precautions on page 113. Fuel Recommendation type research octane number unleaded 91 (or higher) Use only unleaded fuel in your Honda. If you ride your Honda in a country where leaded fuel might be available, take precautions to use only unleaded fuel. Your engine is designed to use any unleaded petrol that has a pump octane number (R + M)/2 of 86 or higher, or a research octane number of 91 or higher. Petrol pumps at service stations normally display the pump octane number. For information on the use of Petrol Containing Alcohol, see page 247. Use of lower octane petrol can cause persistent “pinging” or “spark knock” (a loud rapping noise) which, if severe, can lead to engine damage. Light pinging experienced while operating under a heavy load, such as climbing a hill, is no cause for concern. If pinging or spark knock occurs at a steady engine speed under normal load, change brands of petrol. If pinging or spark knock persists, consult your dealer. Never use stale or contaminated petrol or an oil/petrol mixture. Avoid getting dirt, dust, or water in the fuel tank. Servicing Your Honda 129 14 TRX420FA1 FA2-32HR3B000.book 130 ページ 2013年9月6日 金曜日 午後1時57分 Fuel Fuel Capacity Fuel tank capacity, including reserve: 14.7 ℓ (3.88 US gal , 3.23 Imp gal) Reserve capacity: 4.9 ℓ (1.29 US gal , 1.08 Imp gal) When there is only one segment left in the fuel gauge (page 31), fuel will be low and you should refuel as soon as possible. Refueling Procedure Refer to Safety Precautions on page 113. (2) (1) (1) fuel fill cap (2) filler neck 130 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 131 ページ 2013年9月6日 金曜日 午後1時57分 Fuel 1. To open the fuel fill cap (1), turn it counterclockwise. 2. Add fuel until the level reaches the bottom of the filler neck (2). Avoid over filling the tank. There should be no fuel in the filler neck. WARNING 3 WARNING Petrol is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine and keep heat, sparks and flame away. • Handle fuel only outdoors. • Wipe up spills immediately. 3. After refueling, turn the fuel fill cap clockwise securely. If you replace the fuel fill cap, use only a Honda Genuine replacement part. Servicing Your Honda 131 14 TRX420FA1 FA2-32HR3B000.book 132 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Engine oil quality is a major factor that affects both the performance and the service life of the engine. Using the proper oil (page 133) and filter, and regularly checking, adding, and changing oil will help extend your engine’s life. Even the best oil wears out. Changing oil helps get rid of dirt and deposits in the engine. Operating the engine with old or dirty oil can damage your engine. Running the engine with insufficient oil can cause serious damage to the engine and transmission. Change the engine oil as specified in the maintenance schedule on page 116. When running in very dusty conditions, oil changes should be performed more frequently than specified in the maintenance schedule. 132 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 133 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Oil Recommendation API classification* viscosity (weight) JASO T 903 standard * SG or higher except oils labeled as energy conserving or resource conserving on the circular API service label SAE 10W–30 MA Suggested oils are equal in performance to SJ oils that are not labeled as energy conserving or resource conserving on the circular API service label. • Your ATV does not need oil additives. Use the recommended oil. • Do not use oils with graphite or molybdenum additives. They may adversely affect clutch operation. • Do not use API SH or higher oils displaying a circular API “energy conserving” or “resource conserving” service label on the container. They may affect lubrication and clutch performance. NOT RECOMMENDED OK • Do not use non-detergent, vegetable, or castor based racing oils. Servicing Your Honda 133 14 TRX420FA1 FA2-32HR3B000.book 134 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Other viscosities shown in the following chart may be used when the average temperature in your riding area is within the indicated range. JASO T 903 standard The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines. There are two classes: MA and MB. Oil conforming to the standard is labeled on the oil container. For example, the following label shows the MA classification. (1) (2) (1) oil code (2) oil classification 134 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 135 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Checking & Adding Oil Refer to Safety Precautions on page 113. Check the engine oil level each day before operating your ATV and add if needed. Before riding your ATV, check the engine oil level. 1. Park your ATV on a firm, level surface. 2. Start the engine in a well-ventilated area and let it idle for 3 – 5 minutes. If the air temperature is below 10°C (50°F), let the engine idle for an additional 5 minutes (a total of 10 minutes). 3. Stop the engine and wait 2 – 3 minutes. 4. Remove the oil check lid (1). 5. Remove the dipstick (2) from the front left crankcase cover and wipe it clean. 6. Insert the dipstick without screwing it in, then remove the dipstick and check the oil level. The oil level should be between the upper level mark (3) and the lower level mark (4) on the dipstick. LEFT SIDE LEFT SIDE (3) (4) (1) (1) oil check lid (2) dipstick (2) (3) upper level mark (4) lower level mark (cont’d) Servicing Your Honda 135 14 TRX420FA1 FA2-32HR3B000.book 136 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter 7. If the oil level is near or below the lower level mark, remove the seat (page 124) and the tank cover assembly (page 125). Remove the oil fill cap (5) from the front right crankcase cover and add the specified oil into the fill cap hole, up to the upper level mark on the dipstick. Do not over fill. 8. Reinstall the oil fill cap and dipstick. 9. Install the tank cover assembly. 10. Install the seat. 11. Install the oil check lid. NOTICE Running the engine with an improper oil level can cause serious engine damage. RIGHT SIDE (5) (5) oil fill cap 136 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 137 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Changing Engine Oil & Filter Refer to Safety Precautions on page 113. Your ATV’s oil filter has very specific performance requirements. Use a new Honda Genuine oil filter specified for your model or a filter of equal quality. NOTICE Using the wrong oil filter may result in leaks or engine damage. This procedure requires mechanical skill and professional tools such as a torque wrench as well as a means for disposing of the drained fluid (page 210). If you do not have the skills or the tools, see your dealer. Change the oil with the engine warm to assure complete and rapid draining. Drain the Engine Oil: 1. With the ATV on the level ground, remove the seat (page 124) and the tank cover assembly (page 125), and then remove the oil fill cap from the front right crankcase cover. 2. Place an oil drain pan under the crankcase and remove the engine oil drain bolt (1) and sealing washer (2). UNDER ENGINE (2) (1) (1) engine oil drain bolt (2) sealing washer (cont’d) Servicing Your Honda 137 14 TRX420FA1 FA2-32HR3B000.book 138 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter Install a New Engine Oil Filter: Place shop towels under the oil filter cover because oil will flow out. 1. Remove the oil filter cover (1) and O-rings (2) by removing the bolts (3). Let the remaining oil drain out. Discard the oil filter (4) in an approved manner (page 204). 2. Apply engine oil to a new O-ring and install it to the oil filter cover. Then install a new oil filter. Use only the Honda Genuine oil filter or a filter of equivalent quality specified for your model. Using the wrong Honda filter or a non-Honda filter which is not of equivalent quality may cause engine damage. 3. Install a new filter with the rubber seal (5) facing inward, toward the engine. Make sure the spring (6) and the OUT SIDE mark (7) faces away from the engine, toward the oil filter cover. NOTICE Improper installation of the oil filter can cause serious engine damage. RIGHT SIDE (4) (6) (1) (5) (7) (2) (1) oil filter cover (5) rubber seal (2) O-ring (6) spring (3) bolts (7) OUTSIDE mark (4) oil filter 138 Servicing Your Honda (3) 14 TRX420FA1 FA2-32HR3B000.book 139 ページ 2013年9月6日 金曜日 午後1時57分 Engine Oil & Filter 4. Reinstall the oil filter cover, making sure the bolts are tightened to the specified torque: 10 N·m (1.0 kgf·m , 7 lbf·ft) 5. Pour the drained oil into a suitable container and dispose of it in an approved manner (page 210). NOTICE Improper disposal of drained fluids is harmful to the environment. Add Engine Oil: 1. Reinstall the oil drain bolt with the new sealing washer and tighten it to the specified torque: 25 N·m (2.5 kgf·m , 18 lbf·ft) 2. Fill the crankcase with the recommended grade oil approximately: 3.6 ℓ (3.8 US qt , 3.2 lmp qt) 3. Reinstall the oil fill cap and dipstick. 4. Start the engine and let it idle for 3 – 5 minutes. 5. Stop the engine, wait 2 – 3 minutes and check the oil level. Make sure the oil is between the upper and lower level marks on the dipstick. If necessary, add more oil but do not overfill. 6. Check that there are no oil leaks. 7. Install the tank cover assembly (page 125). 8. Install the seat. If a torque wrench is not used for installation, see your dealer as soon as possible to verify proper assembly. Servicing Your Honda 139 14 TRX420FA1 FA2-32HR3B000.book 140 ページ 2013年9月6日 金曜日 午後1時57分 Rear Final Gear Oil Oil Recommendation type viscosity (weight) hypoid gear oil SAE 80 Changing Oil Refer to Safety Precautions on page 113. Change the oil with the rear final gear at normal operating temperature to assure complete and rapid draining. 140 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 141 ページ 2013年9月6日 金曜日 午後1時57分 Rear Final Gear Oil 1. Park your ATV on a firm, level surface. REAR (2) (1) (1) oil drain bolt (2) oil fill cap 2. Place an oil drain pan under the oil drain bolt (1). 3. Remove the oil fill cap (2), O-ring, drain bolt and sealing washer. 4. After the oil has completely drained, reinstall the drain bolt with a new sealing washer and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) 5. Remove the oil level check bolt (3) and sealing washer. Servicing Your Honda 141 14 TRX420FA1 FA2-32HR3B000.book 142 ページ 2013年9月6日 金曜日 午後1時57分 Rear Final Gear Oil 6. Slowly fill the rear final gear with the recommended oil until oil start to flow out of the oil level check hole (4). Allow oil to settle for 2 – 3 minutes before moving to next step to prevent overfilling. 85 cm3 (2.9 US oz , 3.0 lmp oz) 7. Coat a new O-ring with grease and install it into the fill cap groove and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) 8. Install the oil level check bolt with a new sealing washer and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) 9. Pour the drained oil into a suitable container and dispose of it in an approved manner (page 210). NOTICE Improper disposal of drained fluids is harmful to the environment. REAR (4) (3) (3) oil level check bolt (4) oil level check hole 142 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 143 ページ 2013年9月6日 金曜日 午後1時57分 Front Final Gear Oil Oil Recommendation type viscosity (weight) hypoid gear oil SAE 80 Changing Oil Refer to Safety Precautions on page 113. Change the oil with the front final gear at normal operating temperature to assure complete and rapid draining. Servicing Your Honda 143 14 TRX420FA1 FA2-32HR3B000.book 144 ページ 2013年9月6日 金曜日 午後1時57分 Front Final Gear Oil 1. Park your ATV on a firm, level surface. 2. Place an oil drain pan under the oil drain bolt (1). 3. Remove the oil fill cap (2), O-ring, drain bolt and sealing washer. 4. After the oil has completely drained, reinstall the drain bolt with a new sealing washer and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) 5. Pour the drained oil into a suitable container and dispose of it in an approved manner (page 210). NOTICE Improper disposal of drained fluids is harmful to the environment. 6. Fill the front final gear with the recommended oil. 210 cm3 (7.1 US oz , 7.4 lmp oz) Make sure the oil level is at the lower edge of the oil fill inspection hole (3). 7. Coat a new O-ring with grease and install it into the fill cap groove and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) FRONT (2) (3) (1) (1) oil drain bolt (2) oil fill cap 144 Servicing Your Honda (3) oil fill inspection hole 14 TRX420FA1 FA2-32HR3B000.book 145 ページ 2013年9月6日 金曜日 午後1時57分 Coolant Your ATV’s liquid cooling system dissipates engine heat through the coolant jacket that surrounds the cylinder and cylinder head. Maintaining the coolant will allow the cooling system to work properly and prevent freezing, overheating, and corrosion. Coolant Recommendation Use only high quality ethylene glycol antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines. Check the antifreeze container label. Use only distilled water as a part of the coolant solution. Water that is high in mineral content or salt may be harmful to the aluminum engine. NOTICE Using coolant with silicate inhibitors may cause premature wear of water pump seals or blockage of radiator passages. Using tap water may cause engine damage. The factory provides a 50/50 solution of antifreeze and water in this ATV. This coolant solution is recommended for most operating temperatures and provides good corrosion protection. Decreasing the concentration of antifreeze to less than 40 % will not provide proper corrosion protection. Servicing Your Honda 145 14 TRX420FA1 FA2-32HR3B000.book 146 ページ 2013年9月6日 金曜日 午後1時57分 Coolant Increasing the concentration of antifreeze is not recommended because it decreases cooling system performance. Higher concentrations of antifreeze (up to 60 %) should only be used to provide additional protection against freezing. Check the cooling system frequently during freezing weather. Checking & Adding Coolant Refer to Safety Precautions on page 113. Check the engine coolant level each day before operating your ATV and add if needed. LEFT FRONT (1) (2) (3) (1) reserve tank (2) UPPER level mark (3) LOWER level mark 1. Make sure the vehicle is on level ground. 2. With the engine at normal operating temperature, check the coolant level in the reserve tank (1). It should be between the UPPER (2) and LOWER (3) level marks. If the reserve tank is empty, or if coolant loss is excessive, check for leaks and see your dealer for repair. 146 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 147 ページ 2013年9月6日 金曜日 午後1時57分 Coolant 3. Remove the radiator cap lid (4) and reserve tank cap (5). Always add coolant to the reserve tank. Do not attempt to add coolant by removing the radiator cap. 4. Add coolant to the reserve tank as required to bring the coolant level to the UPPER level mark. (4) FRONT (5) (4) radiator cap lid (5) reserve tank cap 5. After adding coolant, install the parts in the reverse order of removal. Servicing Your Honda 147 14 TRX420FA1 FA2-32HR3B000.book 148 ページ 2013年9月6日 金曜日 午後1時57分 Coolant Coolant Replacement Refer to Safety Precautions on page 113. Coolant should be replaced by your dealer, unless you have the proper tools and service data, and are mechanically qualified. Refer to the official Honda Shop Manual. WARNING 3 WARNING Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you. Always let the engine and radiator cool down before removing the radiator cap. To properly dispose of drained coolant, refer to You & the Environment, page 210. NOTICE Improper disposal of drained fluids is harmful to the environment. 148 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 149 ページ 2013年9月6日 金曜日 午後1時57分 Coolant Radiator Core Refer to Safety Precautions on page 113. Check the air passages for clogging or damage. Remove insects, mud, or any obstruction with low water pressure. Have the radiator checked by your dealer if the air flow is restricted over more than 20 % of the radiator surface. Clean the radiator core after riding the ATV in mud. To clean the radiator core and radiator grill cover: 1. Unhook the reserve tank tube (1). 2. Remove the reserve tank (2) from the left radiator grill cover (3) by removing the bolt (4) and clip (5). 3. Remove the clips (6). 4. Unhook the tab A (7) and tab B (8) on both of the left and right side. 5. Unhook the left side of the centre radiator grill cover hook (9) and slide the left radiator grill cover. 6. Remove the left radiator grill cover. NOTICE Do not apply pressured water directly to the radiator core. The pressured water can damage the radiator core. (cont’d) Servicing Your Honda 149 14 TRX420FA1 FA2-32HR3B000.book 150 ページ 2013年9月6日 金曜日 午後1時57分 Coolant LEFT FRONT (9) (6) (2) (8) (3) (1) (7) (1) reserve tank tube (2) reserve tank (3) left radiator grill cover (4) bolt (5) clip 150 Servicing Your Honda (6) (5) (4) (6) clips (7) tab A (8) tab B (9) centre radiator grill cover hook 14 TRX420FA1 FA2-32HR3B000.book 151 ページ 2013年9月6日 金曜日 午後1時57分 Coolant RIGHT FRONT (7) (8) (7) tab A (8) tab B 7. Remove the centre radiator grill cover (10) by unhooking the right side of the centre radiator grill cover hook (11). 8. Wash the radiator core (12) and centre radiator grill cover. LEFT FRONT (10) (11) (12) (10) centre radiator grill cover (11) centre radiator grill cover hook (12) radiator core 9. Install the removed parts in reverse order of removal. Servicing Your Honda 151 14 TRX420FA1 FA2-32HR3B000.book 152 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner Refer to Safety Precautions on page 113. Proper air cleaner maintenance is very important for off-road vehicles. A dirty, water-soaked, worn-out, or defective air cleaner will allow dirt, dust, mud, and other impurities to pass into the engine. Service the air cleaner more frequently if you ride in unusually wet or dusty areas. Your dealer can help you determine the correct service interval for your riding conditions. Your ATV’s air cleaner has very specific performance requirements. Use a new Honda Genuine air cleaner specified for your model or an air cleaner of equal quality. NOTICE Using the wrong air cleaner may result in premature engine wear. Proper air cleaner maintenance can prevent premature engine wear or damage, expensive repairs, low engine power, poor gas mileage, and spark plug fouling. NOTICE Improper or lack of proper air cleaner maintenance can cause poor performance and premature engine wear. 152 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 153 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner Cleaning 1. Remove the seat (page 124). UNDER SEAT (1) (2) (1) retainer clips (2) air cleaner housing cover 2. Unlatch the retainer clips (1). 3. Remove the air cleaner housing cover (2). Servicing Your Honda 153 14 TRX420FA1 FA2-32HR3B000.book 154 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner 4. Loosen the screw (3) and remove the air cleaner assembly (4) from the air cleaner housing. 5. Remove the clamp (5). 6. Remove the air cleaner (6) from the air cleaner body (7). 7. Gently wash the air cleaner in clean, non-flammable (high flash point) solvent such as kerosene — not petrol. After cleaning, gently squeeze out the remaining solvent. Avoid twisting or wringing the air cleaner. This can tear the foam. 8. Inspect for tears or cracks in the foam or seams of the air cleaner. Replace the air cleaner if it is damaged. 9. Allow the air cleaner to dry thoroughly before applying oil. A wet air cleaner will not fully absorb the oil. 10. Pour clean air filter oil over the entire surface of the air cleaner. Use both hands to evenly spread the oil into the air cleaner. Gently squeeze out any excess oil. (To keep your hands dry, place the air cleaner in a clean plastic bag before spreading the oil into the air cleaner.) UNDER SEAT (7) (4) (3) (5) (6) (3) screw (4) air cleaner assembly (5) clamp 154 Servicing Your Honda (6) air cleaner (7) air cleaner body 14 TRX420FA1 FA2-32HR3B000.book 155 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner 11. Install the air cleaner on the air cleaner body. 12. Apply a thin coat of grease to the sealing surface of the air cleaner assembly. 13. Install the clamp. 14. Insert the air cleaner assembly into the air cleaner housing. 15. Fasten the screw. 16. Reassemble by reversing the disassembly sequence. • Install the air cleaner housing cover and fit the cut out of the tab (8) at the end of the air cleaner. UNDER SEAT (8) (8) tab (8) Servicing Your Honda 155 14 TRX420FA1 FA2-32HR3B000.book 156 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner Dust Cover UNDER SEAT (1) (2) (1) dust cover (2) breather joint Do not push the dust cover (1) too far into the breather joint (2). If the dust cover is dirty, clean it. 156 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 157 ページ 2013年9月6日 金曜日 午後1時57分 Air Cleaner Air Cleaner Housing Drain Tube The air cleaner housing drain tube should be serviced in accordance with the Maintenance Schedule. (Riding through water may require more frequent inspection.) If deposits can be seen in the drain tube, the tube must be cleaned before starting the vehicle. REAR (2) (1) (1) drain tube (3) (3) air cleaner housing (2) clip 1. Remove the drain tube (1) by removing the clip (2) under the air cleaner housing (3). 2. Drain the deposits. 3. Reinstall the drain tube, securing it with the clip. Servicing Your Honda 157 14 TRX420FA1 FA2-32HR3B000.book 158 ページ 2013年9月6日 金曜日 午後1時57分 Engine Throttle Throttle Freeplay Refer to Safety Precautions on page 113. RIGHT HANDLEBAR (A) (B) (2) (3) (4) 3 – 8 mm (0.1 – 0.3 in) (1) (1) throttle lever (2) rubber sleeve (3) throttle cable adjuster (4) lock nut (A) decrease freeplay (B) increase freeplay Inspection Check freeplay at the throttle lever (1). Freeplay: 3 – 8 mm (0.1 – 0.3 in) Adjustment 1. Slide the rubber sleeve (2) back to expose the throttle cable adjuster (3). 2. Loosen the lock nut (4). 3. Turn the adjuster to obtain the correct freeplay. 4. Tighten the lock nut and reinstall the sleeve. 5. After adjustment, check for smooth operation of the throttle lever from fully closed to fully open in all steering positions. 158 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 159 ページ 2013年9月6日 金曜日 午後1時57分 Throttle Throttle Inspection Refer to Safety Precautions on page 113. 1. Check that the throttle assembly is positioned properly and the securing bolts are tight. 2. Check for smooth operation of the throttle lever from fully open to fully closed in all steering positions. If there is a problem, see your dealer. 3. Inspect the condition of the throttle cables from the throttle lever down to the throttle body. If the cable is kinked or chafed, have it replaced. 4. Check the throttle cable for tension or stress in all steering positions. 5. Lubricate the throttle cable with a commercially available cable lubricant to prevent premature wear and corrosion. Servicing Your Honda 159 14 TRX420FA1 FA2-32HR3B000.book 160 ページ 2013年9月6日 金曜日 午後1時57分 Reverse Lock System Reverse Lock System Adjustment Refer to Safety Precautions on page 113. LEFT HANDLEBAR (6) (1) (3) 2 – 4 mm (0.1 – 0.2 in) (4) (5) (1) dust cover (2) reverse assist lever (3) rear brake lever (2) (4) rubber sleeve (5) lock nut (6) adjusting nut 1. Turn over the dust cover (1). 2. Check the reverse assist lever (2) freeplay, measured at the rear brake lever (3) end near the cable: 2 – 4 mm (0.1 – 0.2 in) 3. To adjust, slide the rubber sleeve (4), loosen the lock nut (5) and turn the adjusting nut (6). After adjustment, tighten the lock nut securely. 4. Return the dust cover and rubber sleeve. Other Checks Check the reverse assist lever and cable for loose connections or other damage. If the cable is worn or kinked, have it replaced by your dealer. 160 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 161 ページ 2013年9月6日 金曜日 午後1時57分 Spark Plug Spark Plug Recommendation standard spark plug BKR5E-11 (NGK) or K16PR-U11 (DENSO) Use only the recommended type of spark plug in the recommended heat range. NOTICE Using spark plugs with an improper heat range can cause engine damage. Spark Plug Inspection & Replacement Refer to Safety Precautions on page 113. 1. Remove the seat (page 124) and tank cover assembly (page 125). 2. Clean any dirt from around the spark plug base. 3. Disconnect the spark plug cap (1). Take care to avoid damaging the spark plug wire when disconnecting the cap. 4. Using a spark plug wrench provided in the tool kit, remove the spark plug. 5. Inspect the electrodes and centre porcelain for deposits, corrosion, or carbon fouling. If the corrosion or deposits are heavy, replace the plug. Clean a carbon or wet-fouled plug with a plug cleaner, if available, or a wire brush. Inspect the spark plug electrodes for wear. The centre electrode (2) should have a flat tip and sharp edges, and the side electrode (3) should not be eroded. If the electrodes and insulator tip appear unusually fouled or burned, we suggest that you contact your dealer. 6. Discard the spark plug if there is apparent wear or if the insulator is cracked or chipped. Servicing Your Honda 161 14 TRX420FA1 FA2-32HR3B000.book 162 ページ 2013年9月6日 金曜日 午後1時57分 Spark Plug 7. Using a wire-type feeler gauge, check the spark plug gap (4). If adjustment is necessary, bend the side electrode carefully. The gap should be: 1.00 – 1.10 mm (0.039 – 0.043 in) LEFT SIDE 1.00 – 1.10 mm (4) (0.039 – 0.043 in) (3) (2) (1) (1) spark plug cap (2) centre electrode (3) side electrode (4) spark plug gap 8. With the plug washer attached, thread the spark plug in by hand to prevent cross-threading. 9. Tighten the spark plug: • If the old plug is good: 1/8 turn after it seats. • If installing a new plug, tighten it twice to prevent loosening: a) First, tighten the plug: NGK: 3/4 turn after it seats. DENSO: 1/2 turn after it seats. b) Then loosen the plug. c) Next, tighten the plug again: 1/8 turn after it seats. 162 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 163 ページ 2013年9月6日 金曜日 午後1時57分 Spark Plug NOTICE An improperly tightened spark plug can damage the engine. If a plug is too loose, a piston may be damaged. If a plug is too tight, the threads may be damaged. 10. Connect the spark plug cap. Take care to avoid pinching any cables or wires. 11. Install the remaining parts in the reverse order of removal. Servicing Your Honda 163 14 TRX420FA1 FA2-32HR3B000.book 164 ページ 2013年9月6日 金曜日 午後1時57分 Valves Valve Inspection Refer to Safety Precautions on page 113. Valve clearance should be: intake: 0.15 mm (0.006 in) exhaust: 0.23 mm (0.009 in) Excessive clearance will cause noise. Insufficient clearance will cause loss of power and possibly damage the valves. For those who are mechanically proficient and have the proper tools, instructions on adjusting valve clearances are given in the official Honda Shop Manual. Otherwise, the valves should be adjusted by your dealer. 164 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 165 ページ 2013年9月6日 金曜日 午後1時57分 Spark Arrester Refer to Safety Precautions on page 113. The exhaust system must be periodically purged of accumulated carbon. To purge the system: 1. Select a well-ventilated area free of combustible materials and make sure the exhaust pipe is cool. 2. Remove the bolt (1). 3. Start the engine and rev it up approximately twenty times while momentarily creating exhaust system back pressure by blocking the end of the muffler with a shop towel. 4. Stop the engine and allow the exhaust pipe to cool. 5. Reinstall the bolt securely. REAR (1) (1) bolt Servicing Your Honda 165 14 TRX420FA1 FA2-32HR3B000.book 166 ページ 2013年9月6日 金曜日 午後1時57分 Chassis Suspension Your front and rear suspension systems use springs and hydraulic damping devices that suspend your weight and most of the weight of your ATV. The spring pre-loads for your front and rear suspension systems adjust the amount of force required to begin compression of the spring. The oil damper systems hydraulically control the natural compression and rebound of the suspension springs so that traction and comfort are maintained as the wheels ride over rough terrain. Consider adjusting your suspensions pre-load whenever you change your normal load, by adding or subtracting cargo, accessories, or when riding conditions change. The way you ride your ATV and the type of ride you want to experience can also influence your suspension needs. Lower spring pre-load provides a softer ride and is usually preferred for light loads and smooth terrain. Higher spring pre-load provides a firmer ride and is recommended for heavy loads and rough terrain. Suspension Adjustment Using a pin spanner, which is available from your dealer, the suspensions can be adjusted for rider weight and riding conditions by changing the spring pre-load. Do not attempt to disassemble, service, or dispose of the damper; see your dealer. The instructions found in this owner’s manual are limited to adjustments of the shock assembly only. 166 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 167 ページ 2013年9月6日 金曜日 午後1時57分 Suspension Suspension Spring Pre-Load Refer to Safety Precautions on page 113. FRONT REAR (1) (1) 1 2 3 4 5 (2) (2) 1 2 3 4 5 (1) spring pre-load adjuster (2) pin spanner The spring pre-load adjuster (1) has 5 positions for different load or riding conditions. Use the pin spanner (2) to adjust the shock spring pre-load. Servicing Your Honda 167 14 TRX420FA1 FA2-32HR3B000.book 168 ページ 2013年9月6日 金曜日 午後1時57分 Suspension Position 1: for a light load and smooth terrain. Position 2: standard position. Positions 3 to 5: for when the ATV is more heavily loaded. (Also increase spring pre-load for stiffer suspension.) Make sure that both front shock absorbers are adjusted to the same position. Always adjust the shock absorber position in sequence (1-2-3-4-5 or 5-4-3-2-1). Attempting to adjust directly from 1 to 5 or 5 to 1 may damage the shock absorber. 168 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 169 ページ 2013年9月6日 金曜日 午後1時57分 Brakes The hydraulic disc brakes (front) and single mechanical drum brake (rear) on your ATV dissipate heat generated by the friction of the brake pads on the discs (front) and the brake shoes on the drum (rear) as the wheels are slowed. Hydraulic Disc Front Brake As the front brake pads wear, brake fluid level will drop. A leak in the system will also cause the level to drop. There are no adjustments to perform, but fluid level and pad wear must be inspected periodically. The system must be inspected frequently to ensure there are no fluid leaks. If the right brake lever freeplay does not feel within the normal range while riding, check the brake pads for wear (page 172). Worn pads should be replaced. If the pads are not worn beyond the recommended limit, there is probably air in the brake system. See your dealer to have the air bled from the system. Mechanical Drum Rear Brake If the rear brake lever/parking brake lever or brake pedal freeplay does not feel within the normal range while riding, check the brake shoes for wear (page 177). Brake Fluid Recommendation brake fluid DOT 4 Brake Fluid The recommended brake fluid is DOT 4 Brake Fluid, or any brake fluid of equal quality and performance. Use fresh brake fluid from a sealed container. Be sure to read the label before opening the sealed container. An opened container may be contaminated or may have absorbed moisture from the air. Servicing Your Honda 169 14 TRX420FA1 FA2-32HR3B000.book 170 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Fluid Level Inspection Refer to Safety Precautions on page 113. RIGHT HANDLEBAR (1) (1) LOWER level mark If your inspection indicates a low fluid level, have your dealer add the recommended fluid. Do not add or replace brake fluid, except in an emergency. If you do add fluid, have your dealer check the system as soon as possible. NOTICE Brake fluid can damage plastic and painted surfaces. Handle with care. Wipe up spills immediately. Avoid brake fluid contact with skin or eyes. If it comes in contact with your eyes, wash them out with clean water and immediately call a doctor. If it comes in contact with your skin, wash with clean water and, if necessary, call a doctor. 170 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 171 ページ 2013年9月6日 金曜日 午後1時57分 Brakes With the ATV on a level surface, check the fluid level. It should be above the LOWER level mark (1). If the level is at or below the LOWER level mark, check the brake pads for wear (page 172). Worn brake pads should be replaced. If the pads are not worn, have your brake system inspected for leaks. Other Inspections • Make sure there are no fluid leaks. • Check for deterioration or cracks in the hoses and fittings. If the hoses are worn or cracked, have them replaced by your dealer. Servicing Your Honda 171 14 TRX420FA1 FA2-32HR3B000.book 172 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Brake Pad Wear Refer to Safety Precautions on page 113. Brake pad wear will depend upon the severity of usage and riding conditions. The pads will wear faster in wet or muddy conditions. Inspect the pads visually during all regular service intervals to determine the pad wear. RIGHT FRONT (Left side similar) (2) (1) wear indicator (1) (2) edge of reference mark Check the wear indicator (1). If the wear indicator aligns with the edge of the reference mark (2), both pads must be replaced, see your dealer for this replacement. Always inspect both pads in both the right and left front brake calipers. 172 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 173 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Rear Brake Pedal Freeplay RIGHT SIDE (1) 15 – 20 mm (0.6 – 0.8 in) (1) rear brake pedal Inspection Measure the distance the rear brake pedal (1) moves before the brake starts to take hold. Freeplay, measurement at the tip of the end of the pedal, should be: 15 – 20 mm (0.6 – 0.8 in) If necessary, adjust to the specified range. Servicing Your Honda 173 14 TRX420FA1 FA2-32HR3B000.book 174 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Adjustment RIGHT REAR (3) (2) (2) brake pedal adjusting nut (3) brake arm pin 1. Turn the brake pedal adjusting nut (2), located on the brake operating rod at the rear of the frame. Make sure the cutout on the adjusting nut is properly seated on the brake arm pin (3). 2. Adjust the freeplay of the rear brake pedal. Push the brake arm (4), then check the clearance between the brake arm and the brake arm pin. (4) (4) brake arm 174 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 175 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Rear Brake Lever Freeplay LEFT HANDLEBAR (1) 15 – 20 mm (0.6 – 0.8 in) (1) rear brake lever/parking brake lever Inspection Measure the distance the rear brake lever/parking brake lever (1) moves before the brake starts to take hold. Freeplay (measurement at the tip of the end of the brake lever) should be: 15 – 20 mm (0.6 – 0.8 in) If necessary, adjust to the specified range. Servicing Your Honda 175 14 TRX420FA1 FA2-32HR3B000.book 176 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Adjustment RIGHT REAR (2) (3) (2) brake lever adjusting nut (3) brake arm pin Adjust the freeplay of the rear brake lever/parking brake lever with the front wheels pointed straight ahead. 1. Turn the brake lever adjusting nut (2), located on the brake operating rod at the rear of the frame. Make sure the cutout on the adjusting nut is properly seated on the brake arm pin (3). 2. Adjust the freeplay of the rear brake lever/parking brake lever. Push the brake arm (4) then check the clearance between the brake arm and the brake arm pin. (4) (4) brake arm 176 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 177 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Other Inspections • Check that the rear brake lever and brake pedal assemblies are positioned properly and the securing bolts are tight. • Make sure that the brake cables, brake arm, spring, parking, brake lever and fasteners are in good condition. Brake Shoe Wear Refer to Safety Precautions on page 113. The rear brake is equipped with an external brake wear indicator that lets you check brake wear without disassembly. Application of the brake control causes the arrow on the brake arm to move toward a reference mark on the brake panel. RIGHT REAR (1) arrow (2) brake arm (2) (3) (1) (3) reference mark 1. Apply the brake control and check the movement of the arrow (1) on the brake arm (2). 2. Replace the brake shoe if the arrow aligns with the reference mark (3) on the brake panel upon full application of the brake. If replacement is necessary, see your dealer. Servicing Your Honda 177 14 TRX420FA1 FA2-32HR3B000.book 178 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Brake Light Switch Adjustment Refer to Safety Precautions on page 113. Rear Brake Only: Check the operation of the rear brake light switch (1) at the right side behind the engine from time to time. Adjustment is done by turning the adjusting nut (2). Turn the nut in direction (A) if the switch operates too late and in direction (B) if the switch operates too soon. RIGHT REAR (A) (1) (1) rear brake light switch 178 Servicing Your Honda (2) (B) (2) adjusting nut 14 TRX420FA1 FA2-32HR3B000.book 179 ページ 2013年9月6日 金曜日 午後1時57分 Brakes Draining Water from Brakes Refer to Safety Precautions on page 113. RIGHT REAR (1) (1) rear brake drain bolt 1. Make sure the engine is OFF and the parking brake is set. 2. Remove the rear brake drain bolt (1) and sealing washer from the bottom of the rear brake cover. If any water drains, the brake seals must be replaced by your dealer as soon as possible. 3. Install the rear brake drain bolt with a new sealing washer and tighten it to the specified torque: 12 N·m (1.2 kgf·m , 9 lbf·ft) Servicing Your Honda 179 14 TRX420FA1 FA2-32HR3B000.book 180 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres The tyres are the only point of contact between the ATV and the road. Safety under any riding conditions is dependant upon this small point of contact. Please understand that the tyres will have less grip, as the tread wear decreases. To safely operate your ATV, your wheels and tyres must be the proper type and size. Also, your tyres must be in good condition with adequate tread, and correctly inflated. It is important to properly replace parts according to the replacement schedule. We recommend that you leave this work to the experts with the proper equipment and experience. Wheels that are deformed or damaged must be replaced. Please consult your dealer for replacement. Tyres age, even if they have not been used or have only been used occasionally. Cracking of the tread and sidewall rubber, sometimes accompanied by carcass deformation, is an evidence ageing. Old and aged tyres must be checked by experts to determine the suitability for further use. WARNING 3 WARNING Using tyres that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tyre inflation and maintenance. 180 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 181 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres This ATV is equipped with low pressure tubeless tyres. Although the tyres are designed specifically for off-road use, they are not immune to punctures. Always select your riding area with care. The following pages give detailed information on how and when to check your air pressure, how to inspect your tyres for wear and damage, and our recommendations for tyre repair and replacement. Air Pressure Refer to Safety Precautions on page 113. Properly inflated tyres are most important for safety, and will provide the best combination of handling, tread life, and riding comfort. Generally, underinflated tyres wear unevenly, adversely affect handling, and are more likely to fail from being overheated. Overinflated tyres make your ATV ride harshly, are more prone to damage from surface hazards, and wear unevenly. Make sure the air valve caps are secure. If necessary, install new caps. Servicing Your Honda 181 14 TRX420FA1 FA2-32HR3B000.book 182 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres Always check air pressure when your tyres are “cold.” If you check air pressure when your tyres are “warm” – even if your ATV has only been ridden for a few miles – the readings will be higher. If you let air out of warm tyres to match the recommended cold tyre pressures, the tyres will be underinflated. Be sure to check tyre pressure at the riding site, since changes in altitude can affect air pressure. The recommended “cold” tyre pressures are: RECOMMENDED PRESSURE 182 Servicing Your Honda FRONT REAR 30 kPa (4.4 psi) 30 kPa (4.4 psi) 14 TRX420FA1 FA2-32HR3B000.book 183 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres A manually operated tyre pump should be used rather than the high pressure system found in service stations. This will minimize the possibility of tyre damage from overinflation. If you use a high pressure system at a service station, add air in small amounts and check the pressure increase frequently to prevent possible tyre damage from overinflation. WARNING 3 WARNING Operating this ATV with improper tyres, or with uneven tyre pressure may cause loss of control, and you could be seriously injured or killed. • Always use the size and type tyres specified in this owner’s manual for this vehicle. • Always maintain proper tyre pressure as described in this owner’s manual. Inspection Refer to Safety Precautions on page 113. Whenever you check the tyre pressures, you should also look for: • Bumps or bulges in the side of the tyre or the tread. Replace any tyre that has a bump or bulge. • Cuts, slits, or cracks in the tyres. Replace the tyre if you can see fabric or cord. • Nails or other foreign objects embedded in the side of the tyre or tread. • Excessive tread wear. Servicing Your Honda 183 14 TRX420FA1 FA2-32HR3B000.book 184 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres Also, if you hit a pothole or other hard object while riding, stop as soon as you safely can and carefully inspect the tyres for damage. Tread Wear You must periodically confirm the tread wear depth. FRONT NEW Replace 4 mm (0.16 in) (2) (1) REAR (3) 4 mm (0.16 in) Replace NEW (1) groove depth (2) wear indicator (3) wear indicator location mark To check the condition of a tyre tread, measure the groove depth (1) in the centre of the tyre, or check the wear indicator (2). For best performance, you should replace a tyre before the tread depth at the centre reaches the following limits: front rear 184 Servicing Your Honda 4 mm (0.16 in) 4 mm (0.16 in) 14 TRX420FA1 FA2-32HR3B000.book 185 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres Tyre Repair Refer to Safety Precautions on page 113. A tyre that is repaired, either temporarily or permanently, will have lower speed and performance limits than a new or undamaged tyre. A temporary repair can sometimes be made in an emergency situation. However, since a temporary repair may not hold, you must ride very slowly, preferably without any cargo, and have the tyre replaced or permanently repaired as soon as possible. (For more information on temporary repairs, see If You Have a Flat Tyre, page 222.) A permanent repair, such as an internal plug patch, can be made if a tyre has only a small puncture in the tread area. However you may not be able to safely carry as much weight. If you choose to have a tyre repaired, be sure the repair work is performed by a professional. If you have a tyre professionally repaired at a non-Honda facility, we recommend that you have the work checked by your dealer. Servicing Your Honda 185 14 TRX420FA1 FA2-32HR3B000.book 186 ページ 2013年9月6日 金曜日 午後1時57分 Wheels & Tyres Tyre Replacement Refer to Safety Precautions on page 113. The tyres that came on your ATV were designed to match the performance capabilities of your ATV and provide the best combination of handling, braking, and comfort. It is best to replace all four tyres, however if that is not possible, you must replace the tyres in pairs (front or rear) with tyres of the same size and type as the originals. Never replace just one tyre. WARNING 3 WARNING Installing improper tyres on your ATV can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tyres recommended in this owner’s manual. Used tyres should not be installed if the previous usage record is unknown. The recommended tyres for your ATV are: front AT24 × 8-1211 rear AT24 × 10-1111 MAXXIS M977 MAXXIS M978 When you replace a tyre, remember: Have the tyre replaced by your dealer if possible. If you have a tyre professionally replaced at a non-Honda facility, we recommended that you have the work checked by your dealer. 186 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 187 ページ 2013年9月6日 金曜日 午後1時57分 Guards Skid Plate & Engine Guard Refer to Safety Precautions on page 113. (1) (1) engine guard (2) (2) skid plates The engine guard (1) protects the frame and engine crankcase. The skid plate (2) protects the rear final gear case. Check the guard and plate for cracks, damage or looseness at intervals shown in the Maintenance Schedule. Have the engine guard and skid plates replaced if they are cracked or damaged. If the guard and plate bolts are loose, tighten them securely. Servicing Your Honda 187 14 TRX420FA1 FA2-32HR3B000.book 188 ページ 2013年9月6日 金曜日 午後1時57分 Guards Front Boot Guards & Front Driveshaft Guards Refer to Safety Precautions on page 113. FRONT (1) (2) (1) front boot guards (2) front driveshaft guards Check the front boot guards (1) and front driveshaft guards (2) for cracks, damage or looseness. Tighten any loose fasteners. Replace the front boot guards and front driveshaft guards as required. 188 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 189 ページ 2013年9月6日 金曜日 午後1時57分 Drivetrain Boots Propeller Shaft Boots & Yoke Joint Boot Refer to Safety Precautions on page 113. (1) (2) (1) propeller shaft boots (2) yoke joint boot Check the propeller shaft boots (1) and yoke joint boot (2) for damage or leaking grease. If necessary, have your dealer replace them. Servicing Your Honda 189 14 TRX420FA1 FA2-32HR3B000.book 190 ページ 2013年9月6日 金曜日 午後1時57分 Drivetrain Boots Front Driveshaft Boots Refer to Safety Precautions on page 113. FRONT (1) (1) driveshaft boots Check the driveshaft boots (1) for cuts, damage or leaking grease. If necessary, have your dealer replace them. 190 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 191 ページ 2013年9月6日 金曜日 午後1時57分 Electrical Battery Your ATV has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water as you would with a conventional-type battery. NOTICE Your battery is a maintenance-free type and can be permanently damaged if the cap strip is removed. Electrical accessories use current from the battery, even when the ignition is OFF. Limited operation also allows the battery to discharge. If you have electrical accessories on your ATV or do not ride frequently, we recommend that you charge the battery frequently (see Battery Charging, page 195). If you do not expect to ride your ATV for at least two weeks, we recommend you remove the battery, or at least disconnect the battery cables (negative cable first). If you plan to store your ATV, see Battery Storage, page 192. If your battery seems weak and/or is leaking electrolyte (causing slow starting or other electrical problems), see your dealer. This symbol on the battery means that this product must not be treated as household waste. NOTICE An improperly disposed of battery can be harmful to the environment and human health. Always confirm local regulations for battery disposal. Servicing Your Honda 191 14 TRX420FA1 FA2-32HR3B000.book 192 ページ 2013年9月6日 金曜日 午後1時57分 Battery Battery Storage Refer to Safety Precautions on page 113. If you plan to store your ATV, we recommend you remove the battery and store it where it can be charged at least every 30 days to maintain its service life. If you do not remove the battery, we recommend disconnecting the battery cables (negative cable first). You will get the best storage results from removing the battery and slow charging it every 30 days (see Battery Charging, page 195). Before you remove the battery, be sure to read all the information that follows, as well as the information on the battery label. WARNING 3 WARNING The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance. 192 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 193 ページ 2013年9月6日 金曜日 午後1時57分 Battery The battery is located in a compartment under the rear fender cover. UNDER REAR FENDER COVER (1) (2) (4) (3) (1) rubber band (3) battery (2) negative (–) terminal lead (4) positive (+) terminal lead Removal 1. Make sure the ignition switch is OFF (w). 2. Remove the seat (page 124). 3. Remove the rear fender cover (page 127). 4. Release the rings and remove the rubber band (1). 5. Disconnect the negative (–) terminal lead (2) from the battery (3) first, then disconnect the positive (+) terminal lead (4). (cont’d) Servicing Your Honda 193 14 TRX420FA1 FA2-32HR3B000.book 194 ページ 2013年9月6日 金曜日 午後1時57分 Battery 6. Remove the battery and taking care not to drop the terminal nuts. 7. Charge the battery (see following section). 8. Store your battery in an easy-to-reach location off the floor, in an area protected from freezing temperature and direct sunlight. 9. Clean the compartment after removing the battery for storage. Dry the compartment. 10. Slow charge the battery (see following section) once every 30 days. Installation 1. Check that the battery rubber (5) for damage. If necessary, replace the battery rubber. 2. Make sure the battery rubber is properly installed. 3. Reinstall in the reverse order of removal. Be sure to connect the positive (+) terminal first, then the negative (–) terminal. 4. Make sure all bolts and other fasteners are secure. 5. Install the removed parts in reverse order of removal. (5) (5) battery rubber 194 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 195 ページ 2013年9月6日 金曜日 午後1時57分 Battery Battery Charging Refer to Safety Precautions on page 113. (1) (1) charger Be sure to read the information that came with your battery charger and follow the instructions on the battery. Improper charging may damage the battery. We recommend using a charger (1) designed specifically for your Honda, which can be purchased from your dealer. These units can be left connected for long periods without risking damage to the battery. However, do not intentionally leave the charger connected longer than the time period recommended in the charger’s instructions. Avoid using an automotive-type battery charger. An automotive charger can overheat an ATV battery and cause premature damage. Servicing Your Honda 195 14 TRX420FA1 FA2-32HR3B000.book 196 ページ 2013年9月6日 金曜日 午後1時57分 Appearance Care Frequent cleaning and polishing will keep your Honda looking newer longer. Frequent cleaning also identifies you as an owner who values his ATV. A clean ATV is also easier to inspect and service. General Recommendations Refer to Safety Precautions on page 113. • To clean your ATV, you may use: – water – a mild, neutral detergent and water – a mild spray and wipe cleaner/polisher – a mild spray and rinse cleaner/degreaser and water • Avoid products that contain harsh detergents or chemical solvents that could damage the metal, paint, and plastic on your ATV. • If your ATV is still warm from recent operation, give the engine and exhaust system time to cool off. • Park in a shady area. Washing your ATV in bright sunlight may cause the finish to fade because water droplets intensify the sun’s brightness. • Spotting is also more likely because surface water can dry before you have time to wipe it off. • Clean your ATV regularly to protect surface finishes. • We recommend the use of a garden hose to wash your ATV. High pressure washers (like those at coin-operated car washers) can damage certain parts of your ATV. NOTICE High pressure water (or air) can damage certain parts of your ATV. Water entering the muffler may damage the oxygen sensor. • After cleaning, inspect for damage, wear, and leaks (fuel, oil, coolant and brake fluid). 196 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 197 ページ 2013年9月6日 金曜日 午後1時57分 Appearance Care Washing Your ATV with a Mild Detergent Refer to Safety Precautions on page 113. 1. Cover or plug the exhaust outlet prior to washing your ATV. 2. Rinse your ATV thoroughly with cool water to remove loose dirt. 3. Fill a bucket with cool water. Mix in a mild, neutral detergent, such as dish washing liquid or a product made especially for washing motorcycles or automobiles. 4. Wash your ATV with a sponge or soft towel. As you wash, check for heavy grime. If necessary, use a mild cleaner/degreaser to remove the grime. 5. After washing, rinse your ATV thoroughly with plenty of clean water to remove any residue. Detergent residue can corrode alloy parts. 6. Dry your ATV with a chamois or a soft towel. Leaving water on the surface to air dry can cause dulling and water spots. As you dry, inspect for chips and scratches. 7. Remove the cover or the plug from exhaust outlet. Then, start the engine and let it idle for several minutes. The engine heat will help dry moist areas. 8. As a precaution, ride your ATV at a slow speed and apply the brakes several times. This will help dry the brakes and restore normal braking performance. Servicing Your Honda 197 14 TRX420FA1 FA2-32HR3B000.book 198 ページ 2013年9月6日 金曜日 午後1時57分 Appearance Care Spray Cleaning Your ATV Refer to Safety Precautions on page 113. Avoid using spray cleaner products on the tyres or suspension components. Suggestions for using spray cleaner(s) follow: ATV condition Dust and fingerprint smudges. Light road grimes. Heavy grime. Oil leaks. Brake dust. Dull, corroded chrome or aluminum. 198 Servicing Your Honda Recommended Cleaning Apply a spray cleaner/polish and wipe paint, chrome, glass, and clear plastic. Spray any difficult-to-reach or very dirty areas with a spray cleaner/degreaser. Rinse and dry. Apply a spray cleaner/polish and wipe with a non-abrasive cloth. Use a spray cleaner/degreaser. If necessary, rub with a sponge. Rinse and dry. Apply a spray cleaner/polish and wipe with a non-abrasive cloth. Apply a high quality chrome/ aluminum polish and wipe with a non-abrasive cloth. 14 TRX420FA1 FA2-32HR3B000.book 199 ページ 2013年9月6日 金曜日 午後1時57分 Appearance Care Exhaust Pipe and Muffler Maintenance Refer to Safety Precautions on page 113. The exhaust pipe and muffler are stainless steel but may become stained by mud or dust. To remove mud or dust, use a wet sponge and a liquid kitchen abrasive, then rinse well with clean water. Dry with chamois or a soft towel. If necessary, remove heat stains by using a commercially available fine texture compound. Then rinse by the same manner as removing mud or dust. Servicing Your Honda 199 14 TRX420FA1 FA2-32HR3B000.book 200 ページ 2013年9月6日 金曜日 午後1時57分 Appearance Care Finishing Touches Refer to Safety Precautions on page 113. After washing your ATV, consider using a commercially available spray cleaner/polish or quality liquid or paste wax to finish the job. Use only a non-abrasive polish or wax made specifically for motorcycles or automobiles. Apply the polish or wax according to the instructions on the container. 200 Servicing Your Honda 14 TRX420FA1 FA2-32HR3B000.book 201 ページ 2013年9月6日 金曜日 午後1時57分 Tips Here’s helpful advice on how to prepare for an off-road adventure, how to transport and store your Honda, and how to be an environmentally responsible ATV owner. Tips Preparing for a Ride.................................................................. 202 What to Take to the Riding Area............................................ 202 What to Take on the Trail ...................................................... 203 Transporting Your Honda ......................................................... 204 Storing Your Honda.................................................................. 206 Preparation for Storage.......................................................... 207 Removal from Storage ........................................................... 209 You & the Environment ............................................................ 210 Tips 201 14 TRX420FA1 FA2-32HR3B000.book 202 ページ 2013年9月6日 金曜日 午後1時57分 Preparing for a Ride A safe and enjoyable ride begins with good planning and preparation. Always ride with at least one other person in case you have trouble, and let someone know where you’re going and when you expect to return. Before riding in an unfamiliar area, find out in advance if you need special permits, get maps so you can study the terrain, and talk to other riders who know the area. What to Take to the Riding Area Along with your ATV and riding gear, you should take along some tools and supplies in case you have a problem. For some of the difficulties you might encounter, see Taking Care of the Unexpected, which begins on page 211. We recommend that you always take water, food, a first aid kit, and your owner’s manual. Other items you should consider loading on your truck or trailer include: • a tool kit • tyre repair supplies and tools, and tyres • extra parts, control levers, cables, and spark plugs • wire, duct tape, and rope • extra petrol For safety, all refueling should be done at a gas station on the way to the riding area or at your base camp. 202 Tips 14 TRX420FA1 FA2-32HR3B000.book 203 ページ 2013年9月6日 金曜日 午後1時57分 Preparing for a Ride What to Take on the Trail What you take with you during a ride depends on the kind of terrain, how long you expect to ride, how far you might go from your base camp or help, and how experienced you or your companions are in making repairs. If you decide to take some tools, spare parts, or other supplies on the trail, be sure you can carry them safely and know how to use them. Also, be sure to follow the loading guidelines and weight limit (page 66). Tips 203 14 TRX420FA1 FA2-32HR3B000.book 204 ページ 2013年9月6日 金曜日 午後1時57分 Transporting Your Honda Do not tow your ATV behind a car or other vehicle. When you transport your ATV, we recommend that you carry the vehicle in its normal operating position (on all four wheels). Do not incline the vehicle upright on its rear end. This can damage the vehicle, and leaking petrol could be a hazard. Follow these procedures: 1. Set the parking brake. 204 Tips 14 TRX420FA1 FA2-32HR3B000.book 205 ページ 2013年9月6日 金曜日 午後1時57分 Transporting Your Honda 2. Secure the vehicle with tie-down straps in the areas shown. • Suitable tie-down straps are available from your dealer. • Ordinary rope is not recommended because it can stretch under load. • Using tie-down straps in any other areas can damage your ATV. 3. Rock the vehicle back and forth to make sure the tie-down straps are tight and the vehicle is secure. (1) (2) (3) (1) front cargo rack (2) rear cargo rack (3) trailer hitch Tips 205 14 TRX420FA1 FA2-32HR3B000.book 206 ページ 2013年9月6日 金曜日 午後1時57分 Storing Your Honda If you won’t be riding for an extended period, such as during the winter, thoroughly inspect your ATV and correct any problem before storing it. That way, needed repairs won’t be forgotten and it will be easier to get your ATV running again. We suggest you perform the following procedures to keep your ATV in top condition. These storage procedures will reduce the deterioration that can occur during storage. 206 Tips 14 TRX420FA1 FA2-32HR3B000.book 207 ページ 2013年9月6日 金曜日 午後1時57分 Storing Your Honda Preparation for Storage Refer to Safety Precautions on page 113. 1. Change the engine oil and filter (page 137). 2. Make sure the cooling system is filled with a 50/50 % antifreeze solution (page 145). 3. Fill the fuel tank. Make sure the fuel fill cap is properly installed. (cont’d) Tips 207 14 TRX420FA1 FA2-32HR3B000.book 208 ページ 2013年9月6日 金曜日 午後1時57分 Storing Your Honda 4. To prevent rusting in the cylinder, perform the following: • Remove the spark plug cap from the spark plug (page 161). • Remove the spark plug. Do not connect the spark plug to the spark plug cap. • Pour a tablespoon (15 – 20 cm3) of clean engine oil into the cylinder and cover the spark plug hole with a piece of cloth. • With the engine stop switch in the RUN (e) position, press the start button several times to crank the engine and distribute the oil. • Reinstall the spark plug and spark plug cap. 5. Remove the battery and charge it fully. Store it in an area protected from freezing temperatures and direct sunlight. Slow charge the battery (page 195) once a month. WARNING 3 WARNING The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance. 6. Wash and dry your ATV. Wax all painted surfaces. 7. Inflate the tyres to their recommended pressures (page 181). 8. Store your ATV in an unheated area, free of dampness, away from sunlight, with a minimum of daily temperature variation. 9. Place your ATV on blocks to lift all tyres off the floor. 10. Cover your ATV with a porous material. Avoid using plastic or similar non-breathing, coated materials that restrict air flow and allow heat and moisture to accumulate. 208 Tips 14 TRX420FA1 FA2-32HR3B000.book 209 ページ 2013年9月6日 金曜日 午後1時57分 Storing Your Honda Removal from Storage Refer to Safety Precautions on page 113. 1. Uncover and clean your ATV. 2. If your ATV has been stored for more than four months – change the engine oil (page 137). 3. If your ATV has been stored for more than two months – ask your dealer to drain and replace the fuel. 4. Charge the battery (page 195) as required. Install the battery. 5. Perform a pre-ride inspection (page 61), then test-ride your ATV at low speeds. Tips 209 14 TRX420FA1 FA2-32HR3B000.book 210 ページ 2013年9月6日 金曜日 午後1時57分 You & the Environment Owning and riding an ATV can be enjoyable, but you must do your part to protect nature. When you show respect for the land, wildlife, and other people, you also help preserve the sport of off-road riding. Following are tips on how you can be an environmentally responsible ATV owner. • Tread Lightly. Stay on existing roads and trails, avoid surfaces that are easily damaged, and ride only in areas approved for offroad vehicles. • Keep the Noise Down. Loud vehicles can be offensive. Ride as quietly as possible, don’t remove your spark arrester, and don’t modify the muffler or any other part of your air intake and exhaust systems. Such modifications not only increase noise, they also reduce engine performance and may be illegal. • Choose Sensible Cleaners. Use a biodegradable detergent when you wash your ATV. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Don’t throw cleaning solvents away; see the following guidelines for proper disposal. • Recycle Wastes. It’s illegal and thoughtless to put used engine oil in the trash, down a drain, or on the ground. Used oil, petrol, and cleaning solvents contain poisons that can hurt refuse workers and contaminate our drinking water, lakes, rivers, and oceans. Before changing your oil, make sure you have the proper containers. Put oil and other toxic wastes in separate sealed containers and take them to a recycling centre. Call your local or state office of public works or environmental services to find a recycling centre in your area, and to get instructions on how to dispose of non-recyclable wastes. 210 Tips 14 TRX420FA1 FA2-32HR3B000.book 211 ページ 2013年9月6日 金曜日 午後1時57分 Taking Care of the Unexpected With all the challenges you can encounter off-road, there’s a chance that sometime something may go wrong. This section gives practical advice to help you deal with a wide range of problems. Take time to read this section before you ride. Also review the tips in Preparing for a Ride (page 202). Taking Care of the Unexpected General Guidelines ................................................................... 212 If Your Engine Quits or Won’t Start .......................................... 214 If the Transmission Is Not Functioning Properly ......................... 217 Emergency Gear Selection & Operation .................................... 220 If You Have a Flat Tyre .............................................................. 222 If the High Coolant Temperature Indicator Lights ...................... 225 If a Fuse Blows.......................................................................... 227 If You Crash ............................................................................. 232 If You Lose Your Key ................................................................ 233 If the Battery Is Low (or Dead)................................................... 234 If a Component Fails................................................................. 235 Taking Care of the Unexpected 211 14 TRX420FA1 FA2-32HR3B000.book 212 ページ 2013年9月6日 金曜日 午後1時57分 Taking Care of the Unexpected General Guidelines Keeping your ATV well-maintained is the best way to reduce the possibility of having a problem while riding. However, problems can arise even with well-maintained machines. Remember to take along your owner’s manual, the tool kit that came with your ATV, and any other items (such as tyre repair supplies and additional tools) that might help you solve a problem on your own. If something goes wrong during a ride, the first thing to do is stop as soon as you safely can. Do not continue riding if you have a flat tyre, or you hear an unusual noise, or your ATV just doesn’t feel right. If you continue riding, you could cause more damage and endanger your own safety. After stopping, take time to assess the situation. Carefully inspect your ATV to identify the problem, then consider your options before you decide what to do. If a problem is relatively minor and you have the tools, supplies, and skills to make a permanent repair, you may be able to fix it on the trail and continue riding. Or, you may be able to make a temporary repair that allows you to slowly ride back to your base where you can make a permanent repair or get help. When a problem is more serious – or you don’t have the tools, supplies, experience, or time to deal with it – you need to choose the safest way to get yourself and your ATV back to base. For example, if you are close enough, you (or you and another person) might be able to push it back. 212 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 213 ページ 2013年9月6日 金曜日 午後1時57分 Taking Care of the Unexpected Should you ever have a problem while riding, please follow these guidelines: • Always put personal safety first. • Take time to assess the situation and your options before deciding what to do. • If the problem is relatively minor and you have the tools, supplies, and skills to make a temporary repair, be sure to have permanent repairs made as soon as possible. • Do not continue riding if you are hurt or your ATV is not in safe riding condition. Additional recommendations for specific problems follow. Taking Care of the Unexpected 213 14 TRX420FA1 FA2-32HR3B000.book 214 ページ 2013年9月6日 金曜日 午後1時57分 If Your Engine Quits or Won’t Start Proper operation and maintenance can prevent starting and engine performance problems. In many cases, the cause of the problem may be a simple operational oversight. If you have a problem starting the engine – or experience poor engine performance – the following information may help you. If you can’t correct the problem, see your dealer. If your ATV won’t start, listen as you press the start button. If you don’t hear the starter motor turning, refer to the Starter motor doesn’t operate symptom. If you can hear the starter motor working normally, refer to the Starter motor works, but the engine won’t start symptom. 214 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 215 ページ 2013年9月6日 金曜日 午後1時57分 If Your Engine Quits or Won’t Start SYMPTOM: Starter motor doesn’t operate. POSSIBLE CAUSE WHAT TO DO ignition switch OFF Turn the ignition switch ON. engine stop switch OFF Slide the engine stop switch to RUN. transmission not in Shift into neutral or squeeze neutral the front brake lever. blown fuse Replace with a new fuse of the same rating (page 227). battery lead loose Tighten the battery lead. low (or dead) battery Charge the battery (page 195). If charging doesn’t help, see your dealer. faulty starter motor If all possible causes are negative, the starter motor may be faulty. See your dealer. SYMPTOM: Starter motor works, but the engine won’t start. POSSIBLE CAUSE WHAT TO DO out of fuel Fill the fuel tank. flooded engine See Flooded Engine (page 81). loose or unconnected Install the spark plug cap spark plug cap securely. If the engine still won’t start, see your dealer. loose battery cables Tighten the battery terminal bolts. weak battery Charge the battery (page 195). If charging doesn’t help, see your dealer. Taking Care of the Unexpected 215 14 TRX420FA1 FA2-32HR3B000.book 216 ページ 2013年9月6日 金曜日 午後1時57分 If Your Engine Quits or Won’t Start SYMPTOM: Engine starts, but runs poorly. POSSIBLE CAUSE WHAT TO DO high coolant Check the coolant temperature temperature gauge and high coolant temperature indicator. Refer to If the High Coolant Temperature Indicator Lights, page 225. runs erratically, misfires See your dealer. blubbers (rich fuel See your dealer. mixture) sooty exhaust (rich fuel See your dealer. mixture) detonates or pings If applicable, switch to the under load recommended octane petrol (page 129) or change your brand of petrol. If the problem persists, see your dealer. afterfires (backfires) See your dealer. pre-ignition (runs on See your dealer. after ignition switched OFF) SYMPTOM: Engine starts, but runs poorly or dies when hot. POSSIBLE CAUSE WHAT TO DO poor or inadequate See your dealer. fuel flow due to (ensure clean fuel supply) clogged fuel filter 216 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 217 ページ 2013年9月6日 金曜日 午後1時57分 If the Transmission Is Not Functioning Properly Manual Shift (ESP) Mode: If one or both shift switches do not function, see the following instruction. If proper function cannot be restored, see your dealer. When the engine is running: 1. Stop the ATV. 2. Turn the ignition switch to the OFF (w) position. 3. After the engine stops, turn the ignition switch to the ON (q) position. 4. Press both shift switches and check that they are functioning. 5. If both switches are functioning, shift into neutral and restart the engine. If one or both switches are not functioning, see Emergency Gear Selection & Operation, page 220. When the engine is stopped and the ignition switch is “ON” (q): 1. Turn the ignition switch to the OFF (w) position. 2. Turn the ignition switch to the ON (q) position. 3. Press both shift switches and check that they are functioning. 4. If both switches are functioning, shift into neutral and restart the engine. If one or both switches are not functioning, see Emergency Gear Selection & Operation, page 220. Taking Care of the Unexpected 217 14 TRX420FA1 FA2-32HR3B000.book 218 ページ 2013年9月6日 金曜日 午後1時57分 If the Transmission Is Not Functioning Properly Automatic Shift (AUTO) Mode: When the automatic transmission is not shifting properly, the gear position indicator will show “–” and blink. See your dealer to check and restore the automatic transmission. If the gear position indicator shows “–” and blink while riding, perform the following: 1. Stop the ATV. 2. Turn the ignition switch to the OFF (w) position. 3. After the engine stops, turn the ignition switch to the ON (q) position. 4. Check the gear position indicator. If these efforts do not restore proper operation, have your ATV inspected by your dealer. When the “–” is blinking in the gear position indicator: Restart the engine; drive the ATV to a location where it can be loaded and transported to your dealer. When the display on the gear position indicator returns to normal: You may drive on the ATV as usual after restarting the engine. However, we urge you to have your ATV inspected by your dealer. 218 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 219 ページ 2013年9月6日 金曜日 午後1時57分 If the Transmission Is Not Functioning Properly If the ATV does not move, even through “–” is not blinking in the gear position indicator: If your ATV won’t move, it is possible the transmission is locked. Use the following procedure to unlock the transmission. 1. Make sure the transmission is in neutral. 2. Apply the parking brake. 3. Turn the ignition switch to the OFF (w) position. 4. Loosen the screw (1) and release the lock plate (2). 5. Turn the emergency valve (3) by the screwdriver using the inside of the front fender hole (4) all the way in. With the engine running, your ATV will move forward slowly at idle. 6. See your dealer as soon as possible. LEFT SIDE (1) screw (2) lock plate (4) (2) (1) (3) (3) emergency valve (4) inside of the front fender hole When the battery is low (or dead): • See If the Battery Is Low (or Dead), page 234. Taking Care of the Unexpected 219 14 TRX420FA1 FA2-32HR3B000.book 220 ページ 2013年9月6日 金曜日 午後1時57分 Emergency Gear Selection & Operation If the shift switches do not operate, use the following procedure to manually select a gear so you may drive the vehicle to a location where it can be loaded and transported to your dealer. 1. Turn the ignition switch to the ON (q) position. 2. Remove the seat (page 124), rear fender cover (page 127) and tank cover assembly (page 125). 3. Remove the gear change tool (page 122). 4. Check the neutral indicator. If the transmission is in neutral, go to step 5. If the transmission is not in neutral, use the gear change tool to shift to neutral so you will be able to start the engine. Refer to How to Shift Gears Manually: (page 221). 5. Apply the parking brake. 6. Press the start button to start the engine. 7. Set 2nd gear position. Refer to How to Shift Gears Manually: (page 221). 8. Return the gear change tool to the storage location. 9. Install the tank cover assembly, rear fender cover and seat. 10. Get on the ATV. Ride it at a safe speed to a place where it can be repaired or serviced. 220 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 221 ページ 2013年9月6日 金曜日 午後1時57分 Emergency Gear Selection & Operation How to Shift Gears Manually: (A) (B) (1) (1) gear change tool (A) downshift (counterclockwise) (B) upshift (clockwise) • With the ATV unoccupied, align the hexagonal hole of the gear change tool (1) with the hexagonal end of the secondary spindle which is located on the front crankcase. • To downshift, turn the gear change tool to direction (A). To upshift, turn the gear change tool to direction (B). • If the transmission does not shift, rock the vehicle back and forth and try again. • Return the gear change tool to the storage location. Do not attempt to shift gears manually using the gear change tool while riding. If the transmission is shifted manually when the electric shift system is functioning, the system will shutdown automatically and the shift switches will not operate. To reactivate the system, turn the ignition switch to the OFF (w) position, then turn it back to the ON (q) position. Taking Care of the Unexpected 221 14 TRX420FA1 FA2-32HR3B000.book 222 ページ 2013年9月6日 金曜日 午後1時57分 If You Have a Flat Tyre How you handle a flat tyre on the trail depends on how serious the tyre damage is, and what tools and supplies you have with you. If you have a slow leak or a minor puncture, use the plug method to make a temporary repair. (The plug method is applied from the outside of the tyre and is the same as that for conventional tubeless tyres.) A plug-type repair kit, available at most auto parts stores or service stations, provides a plug, an installation tool, tyre cement, and an instruction sheet. Follow the instructions provided with the repair kit to make a temporary repair. As soon as possible, have the tyre permanently repaired by your dealer. Any tyre that cannot be repaired should be replaced. Whenever the ATV is to be operated far from service facilities or available transportation, we recommend that you carry a tyre pump and a repair kit with the vehicle. If the leak is more serious, or a temporary repair doesn’t hold, the tyre must be replaced. The tyre will also need to be replaced if it is damaged (page 186). Replacing a tyre involves removing and reinstalling the wheel (page 223). If you are unable to repair a flat tyre on the trail, you will need to send for help. We strongly recommend that you do not try to ride with a flat tyre. The ATV will be hard to handle, and if the tyre comes off the rim, it may lock up the wheel and cause you to crash. 222 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 223 ページ 2013年9月6日 金曜日 午後1時57分 If You Have a Flat Tyre Emergency Wheel Removal/Installation Refer to Safety Precautions on page 113. (1) (2) (1) (1) wheel nuts (2) wheel rim Removal 1. Park your ATV on a firm, level surface. 2. Loosen – but do not remove – the wheel nuts (1). 3. Raise the front (or rear) wheels off the ground and place a support block under the vehicle. 4. Remove the wheel nuts. 5. Remove the wheel. • Avoid getting grease, oil, or dirt on the front brake disc or pad surfaces when removing and installing each wheel. Any contamination can cause poor brake performance or rapid pad wear after reassembly. Taking Care of the Unexpected 223 14 TRX420FA1 FA2-32HR3B000.book 224 ページ 2013年9月6日 金曜日 午後1時57分 If You Have a Flat Tyre Installation 1. Position the wheel. 2. Position the wheel nuts so that the tapered sides face the wheel rim (2). 3. Hand-tighten the wheel nuts on the wheel, then lower the ATV to the ground before tightening the nuts in a crisscross (rather than circular) pattern to the specified torque: 64 N·m (6.5 kgf·m , 47 lbf·ft) If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capability. 224 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 225 ページ 2013年9月6日 金曜日 午後1時57分 If the High Coolant Temperature Indicator Lights Normally, the high coolant temperature indicator will only light momentarily when you turn the ignition to ON (q). High coolant temperature may be caused by restriction of air flow to the radiator (such as mud caked on the radiator), extended idling, an oil leak, a coolant leak, a low oil level, a low coolant level, or extended operation under adverse conditions. If the all segment of the coolant temperature gauge and high coolant temperature indicator are on while you’re riding, don’t ignore it. Pull safely to a stop. Stop the engine as soon as it’s safe to do so, and let it cool. NOTICE Continuing to ride with high coolant temperature or an overheated engine can cause serious engine damage. • A steaming engine indicates a coolant leak. Shut the engine off and wait until the steaming stops. Look for a leak, but don’t touch the engine or radiator system. Let everything cool off first. • Check for any restriction of air flow to the radiator. • If there’s no obvious problem, leave the engine on so the fan and coolant circulating system can continue working. Monitor the coolant temperature gauge and high coolant temperature indicator. The indicator may turn off after a brief stop with no load on the engine. • Check the radiator fan. If the fan is not working, turn the engine off. Open the fuse box (page 228) and check the radiator fan fuse. If the fuse is blown, replace it with the proper (same rating) spare fuse. Start the engine. If the all segment of the coolant temperature gauge and high coolant temperature indicator stays on, turn the engine off. If the radiator fan is working, visually check the coolant level in the reserve tank, located under the left front fender. It isn’t necessary to touch the radiator system. (cont’d) Taking Care of the Unexpected 225 14 TRX420FA1 FA2-32HR3B000.book 226 ページ 2013年9月6日 金曜日 午後1時57分 If the High Coolant Temperature Indicator Lights • If the reserve tank is low or empty, don’t ride without adding coolant (page 146). After adding coolant, turn the engine on and check the coolant temperature gauge and high coolant temperature indicator. If the indicator doesn’t turn off, do not ride. The engine needs repair. Transport your ATV to your dealer (page 204). If the temperature drops to normal, check the coolant level. If it has gone down, add more coolant. • Check for an oil leak. • Check the oil level. If necessary, add the recommended oil (page 135) to the upper level mark. If you must leave your ATV to get oil, secure it as much as possible. • Start the engine, and check that the coolant temperature gauge and high coolant temperature indicator goes off. If you are able to resume riding, continue to monitor the coolant temperature gauge and high coolant temperature indicator frequently. If there is an oil leak — do not ride the ATV until the leak is repaired by your dealer (page 204). If there’s a mild coolant leak, you can ride for awhile, carefully watching the coolant temperature gauge and high coolant temperature indicator. Be prepared to stop and add more coolant or water. If the leak is bad, transport your ATV to your dealer (page 204). 226 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 227 ページ 2013年9月6日 金曜日 午後1時57分 If a Fuse Blows All of the electrical circuits on your ATV have fuses to protect them from damage caused by excess current flow (short circuit or overload). If something electrical on your ATV stops working, the first thing you should check for is a blown fuse (1). Check all the fuses before looking elsewhere for another possible cause of the problem. Replace any blown fuses and check component operation. (1) (1) blown fuse The main fuse and the circuit fuses are located under the rear fender cover. TRX420FA2 only: The PS (Electric Power Steering) fuse is located under the rear fender cover. Recommended Fuses main fuse 1 main fuse 2 shift motor other fuses PS (Electric Power Steering) fuse (TRX420FA2 only) 30 A 10 A 30 A 20 A × 2, 10 A 40 A Taking Care of the Unexpected 227 14 TRX420FA1 FA2-32HR3B000.book 228 ページ 2013年9月6日 金曜日 午後1時57分 If a Fuse Blows Main and Shift Motor Fuses Access 1. To prevent an accidental short circuit, turn the ignition switch to OFF (w) before checking or replacing the fuses. 2. Remove the seat (page 124). 3. Remove the rear fender cover (page 127). 4. To access the main fuses (2) (3), and shift motor fuse (4), remove the fuse box cover (5). UNDER REAR FENDER COVER (5) (6) (4) (2) (3) (2) main fuse 1 (3) main fuse 2 (4) shift motor fuse (5) fuse box cover (6) spare fuses 5. Pull the main fuse out. If it is blown, install the spare main fuses (6). 228 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 229 ページ 2013年9月6日 金曜日 午後1時57分 If a Fuse Blows Circuit Fuses Access (8) (7) (7) circuit fuses (8) spare fuses 6. To check or replace a circuit fuse (7), pull the old fuse out of its retaining clips. If the fuse is blown, replace it with a spare fuse (8) of the same rating. If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating. NOTICE Replacing a fuse with one that has a higher rating greatly increases the chance of damage to the electrical system. 7. Install the fuse box cover. 8. Install the rear fender cover. 9. Install the seat. Taking Care of the Unexpected 229 14 TRX420FA1 FA2-32HR3B000.book 230 ページ 2013年9月6日 金曜日 午後1時57分 If a Fuse Blows PS (Electric Power Steering) Fuse Access (TRX420FA2 only) 1. Turn the ignition switch to OFF (w) before checking the fuse. 2. Remove the seat (page 124). 3. Remove the rear fender cover (page 127). 4. To access the PS fuse (1), remove the PS fuse box cover (2). If the PS fuse is blown, see your dealer for this service. 5. Install the PS fuse box cover. 6. Install the rear fender cover. 7. Install the seat. UNDER REAR FENDER COVER (2) (1) (1) PS fuse 230 Taking Care of the Unexpected (2) PS fuse box cover 14 TRX420FA1 FA2-32HR3B000.book 231 ページ 2013年9月6日 金曜日 午後1時57分 If a Fuse Blows If you do not have a spare fuse and you cannot ride the ATV without fixing the problem, take a fuse of the same rating or a lower rating from one of the other circuits that you can do without temporarily. If you replace a blown fuse with a spare fuse that has a lower rating, replace the fuse with the correct rating as soon as you can. Also remember to replace any spare fuses that were installed. If the replacement fuse of the same rating burns out in a short time, there is probably a serious electrical problem on your ATV. Leave the blown fuse in that circuit and have your ATV checked by your dealer. Taking Care of the Unexpected 231 14 TRX420FA1 FA2-32HR3B000.book 232 ページ 2013年9月6日 金曜日 午後1時57分 If You Crash Personal safety is your first priority after a crash. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. If you cannot ride safely, send someone for help. Do not ride if you will risk further injury. If you decide you are capable of riding safely, carefully inspect your ATV for damage and determine if it is safe to ride. Check the tightness of critical nuts and bolts securing such parts as the handlebar, control levers, brakes, and wheels. If there is minor damage, or you are unsure about possible damage but decide to try riding the ATV back to your base, ride slowly and cautiously. Sometimes, crash damage is hidden or not immediately apparent. When you get home, thoroughly check your ATV and correct any problems you find. Also, be sure to have your dealer check the frame and suspension after any serious crash. 232 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 233 ページ 2013年9月6日 金曜日 午後1時57分 If You Lose Your Key Be sure to record your key number (1) at the following space. You’ll need this number to have a duplicate key made. If you lose your key and aren’t carrying a duplicate, either get your spare or have one made. If you don’t know your key number, call the dealer where you purchased your Honda ATV. They may have it listed in their records. If they don’t, transport your ATV to them or the nearest dealer. The dealer will probably have to remove the ignition switch assembly to find the key number so they can make a key for you. KEY NO. __________________________________________________ (1) (1) key number Taking Care of the Unexpected 233 14 TRX420FA1 FA2-32HR3B000.book 234 ページ 2013年9月6日 金曜日 午後1時57分 If the Battery Is Low (or Dead) Jump starting is not recommended, especially if you use an automobile battery. The greater amperage of an automobile battery when the car engine is running can damage your ATV’s electrical system. Bump starting is also not recommended. If you can’t charge the battery or it appears unable to hold a charge, contact your dealer. 234 Taking Care of the Unexpected 14 TRX420FA1 FA2-32HR3B000.book 235 ページ 2013年9月6日 金曜日 午後1時57分 If a Component Fails The brake levers or pedal, control cables, and other components can be damaged as you ride in dense brush or over rocky terrain. Making a trailside repair depends on how serious the damage is and what tools and supplies you have with you. • If any component of the brake system is damaged, you may be able to ride carefully back to your base using the other brake components for slowing or stopping. • If you damage a throttle cable or other critical component, your ATV may be unsafe to ride. Carefully assess the damage and make any repairs that you can. But if there is any doubt, it’s best to be conservative and safe. Taking Care of the Unexpected 235 14 TRX420FA1 FA2-32HR3B000.book 236 ページ 2013年9月6日 236 Taking Care of the Unexpected 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 237 ページ 2013年9月6日 金曜日 午後1時57分 Technical Information This section contains dimensions, capacities, and other technical data, plus information on government requirements and how to break-in your ATV. Technical Information Vehicle Identification ................................................................ 238 Specifications ........................................................................... 240 Break-in Guidelines................................................................... 246 Petrol Containing Alcohol......................................................... 247 Technical Information 237 14 TRX420FA1 FA2-32HR3B000.book 238 ページ 2013年9月6日 金曜日 午後1時57分 Vehicle Identification Serial Numbers The VIN, engine serial number, and key number may be required when ordering replacement parts. Record the numbers here for your reference. The VIN (1) is stamped on the front of the frame. VIN ______________________________________________________ FRONT (1) (1) VIN The engine number (2) is stamped on the upper side of the rear crankcase. ENGINE No. _______________________________________________ LEFT REAR (2) engine number 238 Technical Information (2) 14 TRX420FA1 FA2-32HR3B000.book 239 ページ 2013年9月6日 金曜日 午後1時57分 Vehicle Identification Colour Label & Code The colour label (1) is attached on the left side of the frame. The colour code is helpful when ordering replacement parts. Record the colour and code here for your reference. COLOUR__________________________________________________ CODE ____________________________________________________ LEFT SIDE (1) (1) colour label Technical Information 239 14 TRX420FA1 FA2-32HR3B000.book 240 ページ 2013年9月6日 金曜日 午後1時57分 Specifications Dimensions overall length overall width overall height wheelbase ground clearance Fuel & Lubricants fuel recommendation fuel tank capacity fuel tank reserve engine oil capacity engine oil recommendation 2,103 mm (82.8 in) 1,205 mm (47.4 in) 1,174 mm (46.2 in) 1,268 mm (49.9 in) 183 mm (7.2 in) unleaded petrol, research octane number of 91 or higher 14.7 ℓ (3.88 US gal , 3.23 Imp gal) including reserve 4.9 ℓ (1.29 US gal , 1.08 Imp gal) after disassembly: 4.0 ℓ (4.2 US qt , 3.5 Imp qt) after draining: 3.4 ℓ (3.6 US qt , 3.0 Imp qt) after draining & oil filter change: 3.6 ℓ (3.8 US qt , 3.2 Imp qt) API Service Classification SG or higher except oils labeled as energy conserving or resource conserving on the circular API service label, SAE 10W-30, JASO T 903 standard MA, Honda 4-stroke oil or an equivalent 240 Technical Information 14 TRX420FA1 FA2-32HR3B000.book 241 ページ 2013年9月6日 金曜日 午後1時57分 Specifications Fuel & Lubricants (cont’d) cooling system High quality ethylene glycol recommendation antifreeze containing corrosion protection inhibitors specifically recommended for use in aluminum engines cooling system 1.6 ℓ (1.7 US qt , 1.4 Imp qt) capacity Capacities passenger capacity maximum weight capacity operator only ED type: 187 kg (412 lb) U type: 220 kg (485 lb) rider, all cargo and accessories Engine Specifications displacement 420 cm3 (25.6 cu-in) bore & stroke 86.50 × 71.50 mm (3.406 × 2.815 in) compression ratio 9.9 : 1 spark plug BKR5E-11 (NGK) or (standard) K16PR-U11 (DENSO) spark plug gap 1.00 – 1.10 mm (0.039 – 0.043 in) valve clearance intake: 0.15 mm (0.006 in) (cold) exhaust: 0.23 mm (0.009 in) idle speed 1,400 ± 100 min-1 (rpm) Technical Information 241 14 TRX420FA1 FA2-32HR3B000.book 242 ページ 2013年9月6日 金曜日 午後1時57分 Specifications Power Transmission primary reduction secondary reduction final reduction front rear transmission ratio 1st 2nd 3rd 4th 5th reverse final drive Chassis & Suspension caster trail tyre size, front tyre size, rear tyre pressure, front & rear (cold) 242 Technical Information 2° 5 mm (0.2 in) AT24 × 8-1211 MAXXIS M977 AT24 × 10-1111 MAXXIS M978 Front: 30 kPa (4.4 psi) Rear: 30 kPa (4.4 psi) 2.680 1.818 3.231 3.154 3.058 2.157 1.541 1.178 0.848 3.996 shaft 14 TRX420FA1 FA2-32HR3B000.book 243 ページ 2013年9月6日 金曜日 午後1時57分 Specifications Electrical battery generator Lights headlight (Low/High) brake/tail light neutral indicator reverse indicator high coolant temperature indicator PGM-FI indicator PS (Electric Power Steering) indicator (TRX420FA2 only) Fuses main 1 main 2 shift motor other PS (Electric Power Steering) (TRX420FA2 only) GYZ16H ED type: 12 V –16 Ah (10HR) / 16.8 Ah (20HR) U type: 12 V –16 Ah (10HR) 0.45 kW/5,000 min-1 (rpm) 12 V 35/35 W × 2 LED LED LED LED LED LED 30 A 10 A 30 A 20 A × 2, 10 A 40 A Technical Information 243 14 TRX420FA1 FA2-32HR3B000.book 244 ページ 2013年9月6日 金曜日 Specifications Torque Specification engine oil drain bolt engine oil filter cover bolts rear final gear oil drain bolt rear final gear oil fill cap rear final gear oil level check bolt front final gear oil drain bolt front final gear oil fill cap rear brake drain bolt wheel nuts 25 N·m (2.5 kgf·m, 18 lbf·ft) 10 N·m (1.0 kgf·m, 7 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 64 N·m (6.5 kgf·m, 47 lbf·ft) 244 Technical Information 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 245 ページ 2013年9月6日 金曜日 午後1時57分 Specifications Noise Level & Vibrations Noise level 77 dB(A) EN 15997 Annex H Uncertainty of measurement Vibration on seat EN 15997 Annex I 3 dB(A) Uncertainty of measurement Vibration on handlegrip EN 15997 Annex I N/A Uncertainty of measurement N/A Not exceed 0.5 m/s2 Not exceed 2.5 m/s2 Technical Information 245 14 TRX420FA1 FA2-32HR3B000.book 246 ページ 2013年9月6日 金曜日 午後1時57分 Break-in Guidelines Help assure your ATV’s future reliability and performance by paying extra attention to how you ride during the first operating day or 25 km (15 miles). During this period, avoid full-throttle starts, rapid acceleration, and constant rpm operation. 246 Technical Information 14 TRX420FA1 FA2-32HR3B000.book 247 ページ 2013年9月6日 金曜日 午後1時57分 Petrol Containing Alcohol If you decide to use a petrol containing alcohol (gasohol), be sure its octane rating is at least as high as that recommended above. There are two types of gasohol: One contains ethanol, and the other contains methanol. Do not use gasohol that contains more than 10 % ethanol. Do not use gasohol that contains methanol (methyl or wood alcohol) unless it also contains cosolvents and corrosion inhibitors for methanol. Never use petrol containing more than 5 % methanol, even if it has cosolvents and corrosion inhibitors. Engine performance problems resulting from the use of fuels that contain alcohol are not covered under the warranty. Honda cannot endorse the use of fuels containing methanol since evidence of their suitability is not yet complete. Before buying fuel from an unfamiliar station, try to find out if the fuel contains alcohol. If it does, confirm the type and percentage of alcohol used. If you notice any undesirable operating symptoms while using a petrol that contains alcohol, or one that you think contains alcohol, switch to a petrol that you know does not contain alcohol. Technical Information 247 14 TRX420FA1 FA2-32HR3B000.book 248 ページ 2013年9月6日 金曜日 午後1時57分 Index Index A accessories .................................................................................68 age recommendation .................................................................59 air cleaner, dust cover .............................................................................156 filter ......................................................................................152 housing drain tube ................................................................157 air pressure, gauge ....................................................................................123 tyre .......................................................................................181 apparel, protective ......................................................................56 appearance care .......................................................................196 B bank angle sensor ignition cut-off system ...................................82 battery .....................................................................................191 brake light switch adjustment ...................................................178 brakes, cables ....................................................................................177 draining water from ..............................................................179 fluid ......................................................................................169 front brake lever ......................................................................48 front brake pad wear .............................................................172 parking ....................................................................................49 rear brake lever .......................................................................48 rear brake lever freeplay ........................................................175 rear brake pedal ......................................................................48 rear brake pedal freeplay .......................................................173 shoe wear .............................................................................177 braking .......................................................................................92 break-in guidelines ...................................................................246 button, mode ................................................................................20, 25 248 Index 14 TRX420FA1 FA2-32HR3B000.book 249 ページ 2013年9月6日 金曜日 午後1時57分 Index C capacity, fuel ............................................................................130 care, appearance ......................................................................196 cargo, loading and operational guidelines ..........................................67 weight limit .............................................................................66 cleaning, appearance care ........................................................196 climbing hills ..............................................................................97 clip ...........................................................................................128 colour label ..............................................................................239 compartment, owner’s manual .....................................................................123 storage ....................................................................................52 tool kit ..................................................................................122 component fails ........................................................................235 controls & features .....................................................................40 crash, if you ..............................................................................232 crossing or turning on hills or slopes .........................................102 D digital clock ................................................................................33 dimmer switch, headlight ...........................................................43 dipstick .....................................................................................135 display check ..............................................................................22 display, Multi-function ................................................................26 drivetrain boots ........................................................................189 Index 249 14 TRX420FA1 FA2-32HR3B000.book 250 ページ 2013年9月6日 金曜日 午後1時57分 Index E engine, flooded ...................................................................................81 guard ....................................................................................187 number .................................................................................238 oil ..........................................................................................132 pinging ..................................................................................129 starting ....................................................................................79 stop switch ..............................................................................42 stopping ..................................................................................83 won’t start ............................................................................214 environment .............................................................................210 exhaust system, cleaning ..................................................................................62 purging .................................................................................165 F final gear, front ......................................................................................143 rear .......................................................................................140 flag pole bracket ........................................................................50 flat tyre ....................................................................................222 flooded engine ...........................................................................81 front boot guards .....................................................................188 front driveshaft boots ...............................................................190 front driveshaft guards .............................................................188 fuel, fill cap ...................................................................................130 gauge ......................................................................................31 recommendation ...................................................................129 refueling ................................................................................130 reserve fuel supply .................................................................130 tank capacity .........................................................................130 250 Index 14 TRX420FA1 FA2-32HR3B000.book 251 ページ 2013年9月6日 金曜日 午後1時57分 Index fuses ........................................................................................227 G gap, spark plug ................................................................162, 241 gasohol ....................................................................................247 gear shifting ...............................................................................84 gearshift switch ....................................................................46, 87 guards ......................................................................................187 H headlight dimmer switch ............................................................43 headlight switch .........................................................................43 high coolant temperature indicator ...............................20, 23, 225 hills, crossing or turning on slopes .................................................102 riding down hills ....................................................................101 riding up hills ...........................................................................97 stopping on hills ......................................................................99 horn button ................................................................................43 hourmeter ............................................................................24, 37 I identification, vehicle ................................................................238 ignition switch ............................................................................40 indicators, 4WD indicator .......................................................24, 26, 29, 41 gear position indicator .............................................................30 high coolant temperature indicator ............................20, 23, 225 maintenance minder indicator .................................................38 neutral indicator ................................................................20, 23 PGM-FI indicator ................................................................20, 23 PS (Electric Power Steering) indicator ...........................20, 23, 53 reverse indicator ................................................................20, 23 Index 251 14 TRX420FA1 FA2-32HR3B000.book 252 ページ 2013年9月6日 金曜日 午後1時57分 Index inspection, pre-ride .....................................................................61 K key, lost ........................................................................................233 number .................................................................................233 kit, tool ....................................................................................122 L labels, safety .................................................................................5 lamp check .................................................................................21 lever, 2WD/4WD select .....................................................................41 limit, weight ...............................................................................66 load limits ...................................................................................66 loading guidelines ......................................................................67 lubrication, engine oil ..............................................................................132 front final gear oil ..................................................................143 rear final gear oil ...................................................................140 M maintenance, component locations .............................................................119 hourmeter ...............................................................................38 importance ............................................................................111 minder indicator ......................................................................38 precautions ...........................................................................113 record ...................................................................................118 safety ....................................................................................112 schedule ................................................................................114 tripmeter .................................................................................38 maximum weight limit ................................................................66 252 Index 14 TRX420FA1 FA2-32HR3B000.book 253 ページ 2013年9月6日 金曜日 午後1時57分 Index mode button ........................................................................20, 25 modifications ..............................................................................69 multi-function display .................................................................26 N neutral indicator ...................................................................20, 23 numbers, serial .........................................................................238 O obstacles, riding over ................................................................104 odometer ...................................................................................34 oil, engine ...................................................................................132 front final gear ......................................................................143 rear final gear ........................................................................140 operation component locations ..................................................17 owner’s manual storage ...........................................................123 P parking .....................................................................................107 passenger, no carrying ................................................................59 pavement, no riding on ..............................................................73 petrol .......................................................................................129 petrol containing alcohol ..........................................................247 pinging, engine ........................................................................129 plug, spark ...............................................................................161 pre-ride inspection ......................................................................61 problems, unexpected ..............................................................211 propeller shaft boots & yoke joint boot .....................................189 protective apparel .......................................................................56 PS (Electric Power Steering) .........................................................53 Index 253 14 TRX420FA1 FA2-32HR3B000.book 254 ページ 2013年9月6日 金曜日 午後1時57分 Index R rear final gear oil ......................................................................140 removal, rear fender cover ...................................................................127 seat .......................................................................................124 tank cover assembly ..............................................................125 reverse, assist cable ............................................................................160 assist lever .............................................................................160 gear, shifting into ....................................................................90 indicator ............................................................................20, 23 riding in ...................................................................................90 selector knob ...........................................................................47 rider training ..............................................................................58 riding, basic operations ......................................................................71 clothing ...................................................................................56 over obstacles ........................................................................104 precautions .............................................................................73 preparing for .........................................................................202 safety ........................................................................................2 safety precautions ...................................................................73 through water .......................................................................105 S safety, important precautions ...........................................................113 labels .........................................................................................5 riding precautions ....................................................................73 schedule, maintenance .............................................................114 seat removal .............................................................................124 select lever, 2WD/4WD select .....................................................................41 254 Index 14 TRX420FA1 FA2-32HR3B000.book 255 ページ 2013年9月6日 金曜日 午後1時57分 Index serial numbers ..........................................................................238 shifting gears ..............................................................................84 skid plates ................................................................................187 skidding or sliding ......................................................................96 spark arrester ...........................................................................165 spark knock ..............................................................................129 spark plug ................................................................................161 specifications ............................................................................240 speedometer ........................................................................24, 26 stalled engine .............................................................................82 stalling on a hill ..........................................................................99 start button ................................................................................42 starting, engine .....................................................................................79 troubleshooting .....................................................................214 stop switch, engine ....................................................................42 stopping engine .........................................................................83 storage, ATV .......................................................................................206 compartment ..........................................................................52 owner’s manual .....................................................................123 suspension, adjustment ............................................................................166 spring pre-load ......................................................................167 switch, downshift ..........................................................................46, 87 engine stop .............................................................................42 headlight .................................................................................43 headlight dimmer ....................................................................43 ignition ....................................................................................40 upshift ...............................................................................46, 87 Index 255 14 TRX420FA1 FA2-32HR3B000.book 256 ページ 2013年9月6日 金曜日 午後1時57分 Index T throttle, cable .............................................................................158, 159 lever ........................................................................44, 158, 159 tool kit .....................................................................................122 trailer hitch .................................................................................51 trailer towing, operational guidelines .............................................................67 weight limits ............................................................................66 training, rider .............................................................................58 transporting your ATV ..............................................................204 tripmeter ....................................................................................34 trouble, unexpected .................................................................211 troubleshooting, starting ..........................................................214 turning, on hills or slopes ....................................................................102 on level ground .......................................................................94 tyres, air pressure ............................................................................181 flat ........................................................................................222 repairing ................................................................................185 replacing ...............................................................................186 thread conditions ..........................................................183, 184 V valve clearance .........................................................................164 vehicle identification no. (VIN) ..................................................238 W warning labels ..............................................................................5 washing your ATV ....................................................................197 256 Index 14 TRX420FA1 FA2-32HR3B000.book 257 ページ 2013年9月6日 金曜日 午後1時57分 Index water, draining from brakes .............................................................179 riding through .......................................................................105 weight limit ................................................................................66 wheel removal ..........................................................................223 Index 257 14 TRX420FA1 FA2-32HR3B000.book 258 ページ 2013年9月6日 金曜日 午後1時57分 Manufacturer and Authorised Representative for EU Market Manufacturer and Authorised Representative for EU Market Manufacturer Honda of South Carolina Mfg., Inc. 1111 Honda way Timmonsville, South Carolina 29161, U.S.A. Authorised Representative for EU Market Honda Motor Europe Ltd Belgian Branch p/a Honda Motor Europe Ltd - Aalst Office Wijngaardveld 1 (Noord V) B-9300 Aalst (Belgium) 258 Manufacturer and Authorised Representative for EU Market 14 TRX420FA1 FA2-32HR3B000.book 259 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 260 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 261 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 262 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 263 ページ 2013年9月6日 金曜日 午後1時57分 14 TRX420FA1 FA2-32HR3B000.book 264 ページ 2013年9月6日 金曜日 午後1時57分