12 VFR1200X-32MGH600.book 1 ページ ２０１２年７月５日 木曜日 午後１０時５７分 This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when it is resold. This publication includes the latest production information available before printing. Honda Motor Co., Ltd. reserves the right to make changes at any time without notice and without incurring any obligation. No part of this publication may be reproduced without written permission. The vehicle pictured in this owner’s manual may not match your actual vehicle. © 2012 Honda Motor Co., Ltd. 12 VFR1200X-32MGH600.book 2 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Welcome Congratulations on your purchase of a new Honda motorcycle. Your selection of a Honda makes you part of a worldwide family of satisfied customers who appreciate Honda’s reputation for building quality into every product. To ensure your safety and riding pleasure: ● Read this owner’s manual carefully. ● Follow all recommendations and procedures contained in this manual. ● Pay close attention to safety messages contained in this manual and on the motorcycle. The following codes in this manual indicate each country. ● The illustrations here in are based on the VFR1200XD ED type. Country Codes ● Code VFR1200X E ED F U KO VFR1200XD E ED F U BR, II BR Country UK European direct sales France, Belgium Australia, New Zealand Korea UK European direct sales France, Belgium Australia, New Zealand Brazil *The specifications may vary with each locale. 12 VFR1200X-32MGH600.book 3 ページ ２０１２年７月５日 木曜日 午後１０時５７分 A Few Words About Safety Your safety, and the safety of others, is very important. Operating this motorcycle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on safety labels and in this manual. This information alerts you to potential hazards that could hurt you or others. Of course, it is not practical or possible to warn you about all hazards associated with operating or maintaining a motorcycle. You must use your own good judgement. You will find important safety information in a variety of forms, including: ● Safety labels on the motorcycle ● Safety Messages preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION. These signal words mean: 3 DANGER You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 WARNING You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. 3 CAUTION You CAN be HURT if you don’t follow instructions. Other important information is provided under the following titles: NOTICE Information to help you avoid damage to your motorcycle, other property, or the environment. 12 VFR1200X-32MGH600.book 4 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Contents Motorcycle Safety P. 2 Operation Guide P. 18 Maintenance P. 48 Troubleshooting P. 90 Information P. 111 Specifications P. 125 Index P. 128 12 VFR1200X-32MGH600.book 2 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Motorcycle Safety This section contains important information for safe riding of your motorcycle. Please read this section to ensure rider and passenger safety. Safety Guidelines .........................................P. 3 Image Labels.................................................P. 6 Safety Precautions .....................................P. 11 Riding Precautions .....................................P. 12 Accessories & Modifications......................P. 16 Loading .......................................................P. 17 12 VFR1200X-32MGH600.book 3 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Safety Guidelines Safety Guidelines Always Wear a Helmet It’s a proven fact: helmets and protective apparel significantly reduce the number and severity of head and other injuries. So always wear an approved motorcycle helmet and protective apparel. 2 P. 11 Before Riding Take Time to Learn & Practice Even if you have ridden other motorcycles, practice riding in a safe area to become familiar with how this motorcycle works and handles, and to become accustomed to the motorcycle’s size and weight. Ride Defensively Always pay attention to other vehicles around you, and do not assume that other drivers see you. Be prepared to stop quickly or perform an evasive maneuver. Make sure that you are physically fit, mentally focused and free of alcohol and drugs. Check continued 3 Motorcycle Safety Follow these guidelines to ensure your safety: ● Perform all routine and regular inspections specified in this manual. ● Stop the engine and keep sparks and flame away before filling the fuel tank. ● Do not run the engine in enclosed or partly enclosed areas. Carbon monoxide in exhaust gases is toxic and can kill you. that you and your passenger are both wearing an approved motorcycle helmet and protective apparel. Instruct your passenger on holding onto the grab rails, leaning with you in turns, and keeping their feet on the footpegs, even when the motorcycle is stopped. 12 VFR1200X-32MGH600.book 4 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Safety Guidelines Make Yourself Easy to See Motorcycle Safety Make yourself more visible, especially at night, by wearing bright reflective clothing, positioning yourself so other drivers can see you, signaling before turning or changing lanes, and using your horn when necessary. Ride within Your Limits Never ride beyond your personal abilities or faster than conditions warrant. Fatigue and inattention can impair your ability to use good judgement and ride safely. Don’t Drink and Ride Alcohol and riding don’t mix. Even one alcoholic drink can reduce your ability to respond to changing conditions, and your reaction time gets worse with every additional drink. Don’t drink and ride, and don’t let your friends drink and ride either. 4 Keep Your Honda in Safe Condition It’s important to keep your motorcycle properly maintained and in safe riding condition. Inspect your motorcycle before every ride and perform all recommended maintenance. Never exceed load limits (2 P. 17), and do not modify your motorcycle or install accessories that would make your motorcycle unsafe (2 P. 16). If You are Involved in a Crash Personal safety is your first priority. If you or anyone else has been injured, take time to assess the severity of the injuries and whether it is safe to continue riding. Call for emergency assistance if needed. Also follow applicable laws and regulations if another person or vehicle is involved in the crash. If you decide to continue riding, first evaluate the condition of your motorcycle. If the engine is still running, turn it off. Inspect for fluid leaks, 12 VFR1200X-32MGH600.book 5 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Safety Guidelines 3 WARNING Motorcycle Safety check the tightness of critical nuts and bolts, and check the handlebar, control levers, brakes, and wheels. Ride slowly and cautiously. Your motorcycle may have suffered damage that is not immediately apparent. Have your motorcycle thoroughly checked at a qualified service facility as soon as possible. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any areas or activities that expose you to carbon monoxide. Carbon Monoxide Hazard Exhaust contains poisonous carbon monoxide, a colourless, odorless gas. Breathing carbon monoxide can cause loss of consciousness and may lead to death. If you run the engine in confined or even partly enclosed area, the air you breathe could contain a dangerous amount of carbon monoxide. Never run your motorcycle inside a garage or other enclosure. 5 12 VFR1200X-32MGH600.book 6 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Image Labels Image Labels Motorcycle Safety Except KO, BR, II BR type The following pages describe the label meanings. Some labels warn you of potential hazards that could cause serious injury. Others provide important safety information. Read this information carefully and don’t remove the labels. If a label comes off or becomes hard to read, contact your dealer for a replacement. There is a specific symbol on each label. The meanings of each symbol and label are as follows. 6 Read instructions contained in Owner’s Manual carefully. Read instructions contained in Shop Manual carefully. In the interest of safety, take the motorcycle to be serviced only by your dealer. DANGER (with RED background) You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions. WARNING (with ORANGE background) You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions. CAUTION (with YELLOW background) You CAN be HURT if you don’t follow instructions. 12 VFR1200X-32MGH600.book 7 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Image Labels continued 7 Motorcycle Safety BATTERY LABEL DANGER • Keep flame and spark away from the battery. Battery produce explosive gas that can cause explosion. • Wear the eye protection and rubber gloves when handling the battery, or you can get burned or lose your eyesight by the battery electrolyte. • Do not allow children and other people to touch a battery unless they understand proper handling and hazards of the battery very well. • Handle the battery electrolyte with extreme care as it contains dilute sulfuric acid. Contact with your skin or eyes can burn you or cause loss of your eyesight. • Read this manual carefully and understand it before handling the battery. Neglect of the instructions can cause personal injury and damage to the motorcycle. • Do not use a battery with the electrolyte at or below the lower level mark. It can explode causing serious injury. 12 VFR1200X-32MGH600.book 8 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Image Labels Motorcycle Safety RADIATOR CAP LABEL DANGER NEVER OPEN WHEN HOT. Hot coolant will scald you. Relief pressure valve begins to open at 1.1 kgf/cm2. ACCESSORIES AND LOADING WARNING LABEL WARNING ACCESSORIES AND LOADING • The safety stability and handling of this motorcycle may be affected by the addition of accessories and luggage. • Read carefully the instructions contained in user’s manual and installation guide before installing any accessory. • The total weight of accessories and luggage added to rider’s and passenger’s weight should not exceed 194 kg (428 lb), which is the maximum weight capacity. • The luggage weight must not exceed 18.5 kg (41 lb) under any circumstances. • The fitting of large fork-mounted or large handlebar mounted fairing is not recommended. 8 12 VFR1200X-32MGH600.book 9 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Image Labels TYRE INFORMATION LABEL Cold tyre pressure: [Driver only] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 290 kPa (2.90 kgf/cm2, 42 psi) [Driver and passenger] Front 250 kPa (2.50 kgf/cm2, 36 psi) Rear 290 kPa (2.90 kgf/cm2, 42 psi) Tyre size: Front 110/80R19M/C 59V Rear 150/70R17M/C 69V Tyre brand: PIRELLI BRIDGESTONE Front SCORPION TRAIL E BW-501 RADIAL F Rear SCORPION TRAIL E BW-502 RADIAL F continued 9 Motorcycle Safety REAR CUSHION LABEL GAS FILLED Do not open. Do not heat. 12 VFR1200X-32MGH600.book 10 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Image Labels Motorcycle Safety 10 SAFETY REMINDER LABEL For your protection, always wear helmet, protective apparel. FUEL LABEL Unleaded petrol only Premium Recommended CARGO LIMIT LABEL Do not exceed 10 kg (22 lb) 12 VFR1200X-32MGH600.book 11 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Safety Precautions Safety Precautions ● Face shield with unobstructed field of vision handlebar and feet on the footpegs. ● Keep passenger’s hands onto the grab rail, passenger’s feet on the footpegs while riding. ● Always consider the safety of your passenger, as well as other drivers and riders. Protective Apparel Make sure that you and any passenger are wearing an approved motorcycle helmet, eye protection, and high-visibility protective clothing. Ride defensively in response to weather and road conditions. ❙ Helmet Safety-standard certified, high-visibility, correct size for your head ● Must fit comfortably but securely, with the chin strap fastened 3 WARNING Not wearing a helmet increases the chance of serious injury or death in a crash. Motorcycle Safety or other approved eye protection ● Ride cautiously and keep your hands on the Make sure that you and any passenger always wear an approved helmet and protective apparel. ❙ Gloves Full-finger leather gloves with high abrasion resistance ❙ Boots or Riding Shoes Sturdy boots with non-slip soles and ankle protection ❙ Jacket and Trousers Protective, highly visible, long-sleeved jacket and durable trousers for riding (or a protective suit). 11 12 VFR1200X-32MGH600.book 12 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Riding Precautions Riding Precautions Motorcycle Safety 12 Running-in Period During the first 500 km (300 miles) of running, follow these guidelines to ensure your motorcycle’s future reliability and performance. ● Avoid full-throttle starts and rapid acceleration. ● Avoid hard braking and rapid down-shifts. ● Ride conservatively. Brakes Observe the following guidelines: ● Avoid excessively hard braking and downshifts. u Sudden braking can reduce the motorcycle stability. u Where possible, reduce speed before turning; otherwise you risk sliding out. ● Exercise caution on low traction surfaces. u The tyres slip more easily on such surfaces and braking distances are longer. ● Avoid continuous braking. u Repeated braking, such as when descending long, steep slopes can seriously overheat the brakes, reducing their effectiveness. Use engine braking with intermittent use of the brakes to reduce speed. 12 VFR1200X-32MGH600.book 13 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Riding Precautions ❙ Engine Braking Your motorcycle is equipped with a brake system that distributes the braking force between the front and rear brakes. The distribution of the braking force applied to the front and rear brakes is different when operating the lever only and when operating the pedal only. For full braking effectiveness, operate both the lever and pedal together. Engine braking helps slow your motorcycle down when you release the throttle. For further slowing action, downshift to a lower gear. Use engine braking with intermittent use of the brakes to reduce speed when descending long, steep slopes. This model is also equipped with an Anti-lock Brake System (ABS) designed to help prevent the brakes from locking up during hard braking. Always use the recommended tyres to ensure correct ABS operation. ● ABS does not reduce braking distance. In certain circumstances, ABS may result in a longer stopping distance. ● ABS does not function at speeds below 10 km/h (6 mph). ● The brake lever and pedal may recoil slightly when applying the brakes. This is normal. Motorcycle Safety ❙ Combined ABS ❙ Wet or Rainy Conditions Road surfaces are slippery when wet, and wet brakes further reduce braking efficiency. Exercise extra caution when braking in wet conditions. If the brakes get wet, apply the brakes while riding at low speed to help them dry. continued 13 12 VFR1200X-32MGH600.book 14 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Riding Precautions Parking Motorcycle Safety ● Park on a firm, level paved surface. ● If you must park on a slight incline or loose surface, park so that the motorcycle cannot move or fall over. ● Make sure that high-temperature parts cannot come into contact with flammable materials. ● Do not touch the engine, muffler, brakes and other high-temperature parts until they cool down. ● To reduce the likelihood of theft, always lock the handlebar and remove the key when leaving the motorcycle unattended. Use of an anti-theft device is also recommended. ❙ Parking with the Side Stand 1. Stop the engine. 2. Push the side stand down. 14 3. Slowly lean the motorcycle to the left until its weight rests on the side stand. 4. Turn the handlebar fully to the left. u Turning the handlebar to the right reduces stability and may cause the motorcycle to fall. 5. Turn the ignition switch to the LOCK position and remove the key. 2 P. 35 12 VFR1200X-32MGH600.book 15 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Riding Precautions Refuelling and Fuel Guidelines TCS (Traction Control System) TCS (Traction Control System) assists you in maintaining traction while accelerating on slippery surfaces by regulating the engine’s power output when it senses the rear wheel starting to lose traction. TCS may not compensate rough condition of roads or rapid and improper throttle operations. Always ride with a sufficient caution to the road and weather conditions. In certain unusual conditions when your motorcycle gets stuck in shallow mud or fresh snow, it may be easier to free it with the TCS temporarily switched off. It may also help to make it easier to maintain the balance and control in such condition as riding in an off-road terrain. Motorcycle Safety Follow these guidelines to protect the engine and catalytic converter: ● Use only unleaded petrol. ● Use recommended octane number. Using lower octane petrol will result in decreased engine performance. ● Do not use fuels containing a high concentration of alcohol. 2 P. 116 ● Do not use stale or contaminated petrol or an oil/petrol mixture. ● Avoid getting dirt or water in the fuel tank. TCS does not work in case of rear wheel lock caused by a sudden closing of the throttle. Do not close the throttle suddenly especially on the slippery road surface. Always use the recommended tyres to ensure correct TCS operation. 15 12 VFR1200X-32MGH600.book 16 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Accessories & Modifications Motorcycle Safety 16 Accessories & Modifications We strongly advise that you do not add any accessories that were not specifically designed for your motorcycle by Honda or make modifications to your motorcycle from its original design. Doing so can make it unsafe. Modifying your motorcycle may also void your warranty and make your motorcycle illegal to operate on public roads and highways. Before deciding to install accessories on your motorcycle be certain the modification is safe and legal. 3 WARNING Improper accessories or modifications can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding accessories and modifications. Do not pull a trailer with, or attach a sidecar to, your motorcycle. Your motorcycle was not designed for these attachments, and their use can seriously impair your motorcycle’s handling. 12 VFR1200X-32MGH600.book 17 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Loading Loading motorcycle’s handling, braking and stability. Always ride at a safe speed for the load you are carrying. ● Avoid carrying an excessive load and keep within specified load limits. 2 Maximum weight capacity / Maximum luggage weight P. 125 ● Tie all luggage securely, evenly balanced and close to the centre of the motorcycle. ● Do not place objects near the lights or the muffler. Overloading or improper loading can cause a crash and you can be seriously hurt or killed. Follow all load limits and other loading guidelines in this manual. Motorcycle Safety ● Carrying extra weight affects your 3 WARNING 17 12 VFR1200X-32MGH600.book 18 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Parts Location Operation Guide Rear brake fluid reservoir (P76) Main fuse B (P110) Battery (P67) Front brake fluid reservoir (P76) Front brake lever (P84) Throttle grip (P82) Engine oil fill cap (P68) Clutch oil filter (VFR1200XD) (P72) Right under cowl (P65) Engine oil filter (P69) Engine oil level inspection window (P68) Engine oil drain bolt (P69) Right engine heat guard (P65) Coolant reserve tank (P74) 18 12 VFR1200X-32MGH600.book 19 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Clutch lever (VFR1200X) (P84) Clutch fluid reservoir (VFR1200X) (P79) Front suspension spring preload /rebound damping adjuster (P85) Seat (P63) Fuse box (P109) Main fuse A (P109) Rear suspension rebound damping adjuster (P86) Final gear cover (P64) Final drive oil drain bolt Operation Guide Parking brake lever (VFR1200XD) (P78) (P81) Final drive oil fill hole cap (P81) Shift lever (VFR1200X) Side stand (P80) (P40) 19 12 VFR1200X-32MGH600.book 20 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments (VFR1200X) Tachometer red zone (excessive engine rpm range) Operation Guide Tachometer TOTAL/TRIP button FCD button NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. TOTAL/TRIP button & FCD button (E type only) Press and hold both buttons to change the speed, mileage and fuel mileage units (“km/h” & “km” & “km/L” or “mph” & “mile” & “mile/L”) for the speedometer, odometer, and tripmeter. Press FCD button to select either ”km/h” & “km” & “km/L” or “mph” & “mile” & “mile/L”, then press TOTAL/TRIP button to set. 20 12 VFR1200X-32MGH600.book 21 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Speedometer Operation Guide Fuel gauge Remaining fuel when only 1st (E) segment starts flashing: approximately 4.0 litres (1.06 US gal, 0.88 Imp gal) At the same time, the available driving distance is displayed. Display Check When the ignition switch is turned on, all the mode and digital segments will show. If any part of these displays does not come on when it should, have your dealer check for problems. continued 21 12 VFR1200X-32MGH600.book 22 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments (Continued) Operation Guide TOTAL/TRIP button FCD button Air temperature gauge (AIR) Display range: -10 to 50 ºC • Below -11 ºC: “ ” displays • Above 50 ºC: - Air temperature gauge (flashing digits) u The temperature readout may be incorrect at low speeds due to reflected heat. 22 Clock (12-hour display) To set the clock (P24) 12 VFR1200X-32MGH600.book 23 ページ ２０１２年７月５日 木曜日 午後１０時５７分 u Even if the engine coolant temperature is low, the cooling fan may start running when you rev up the engine. This is normal. Backlight brightness adjustment (P25) Operation Guide Coolant temperature gauge ( ) • Above 122 ºC: - High coolant temperature indicator lights - 5th (H) segment flashes Gear position indicator Shows 1st to 6th gear position. Odometer [TOTAL] & Tripmeter [TRIP A/B] TOTAL/TRIP button switches between odometer & tripmeters. • Odometer: Total distance ridden. • Tripmeter: Distance ridden since tripmeter was reset (press and hold TOTAL/TRIP button to reset to 0.0 km/mile. At the same time reset the average fuel mileage). continued 23 12 VFR1200X-32MGH600.book 24 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments (Continued) To set the clock: Operation Guide !a Turn the ignition switch ON while pressing and holding the FCD button. The hour digits start flashing. !b Press FCD button until the desired hour is displayed. u Press and hold to advance the hour fast. !c Press TOTAL/TRIP button. The minute digits start flashing. !d Press FCD button until the desired minute is displayed. u Press and hold to advance the minute fast. 24 !e Press TOTAL/TRIP button. The clock is set. u The time can also be set by turning the ignition switch off. The display will stop flashing automatically and the adjustment will be cancelled if the button is not pressed for about 30 seconds. 12 VFR1200X-32MGH600.book 25 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Backlight brightness adjustment: You can adjust the brightness five levels. !b Press FCD button until the desired brightness is displayed. Operation Guide !a Press and hold TOTAL/TRIP button when the display in the odometer. The brightness digits start flashing. !c Press TOTAL/TRIP button. The brightness is set. u The brightness can also be set by turning the ignition switch off. The adjustment will be cancelled if the button is not pressed for about 30 seconds. 25 12 VFR1200X-32MGH600.book 26 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments (Continued) Operation Guide 26 Fuel mileage meter The current fuel mileage, average fuel mileage and no indication can be selected to press the FCD button. Current fuel mileage Average fuel mileage No indication 12 VFR1200X-32MGH600.book 27 ページ ２０１２年７月５日 木曜日 午後１０時５７分 When the 1st (E) segment of the fuel gauge is flashed Available driving distance is displayed. Then the amount of remaining fuel, current fuel mileage, average fuel mileage, no indication and available driving distance can be selected to press the FCD button. Amount of remaining fuel Current fuel Average fuel mileage mileage No indication Operation Guide Available driving distance continued 27 12 VFR1200X-32MGH600.book 28 ページ ２０１２年７月５日 ❙ Indication mode change of current fuel mileage and average fuel mileage Except E type Operation Guide 28 Press and hold FCD button to switch between “km/L” or “L/100 km”. 木曜日 午後１０時５７分 ❙ Current fuel mileage Current fuel mileage shows the current, or instant fuel mileage you are getting. When your motorcycle speed is 5 km/h (3 mph) or below, “ ” is displayed. ❙ Average fuel mileage The average fuel mileage is based on the each tripmeter A and tripmeter B. The average fuel mileage since tripmeter was reset. When “ ” is displayed, see your dealer for service. Average fuel mileage is also reset when the tripmeter is reset. (P23) 12 VFR1200X-32MGH600.book 29 ページ ❙ ２０１２年７月５日 午後１０時５７分 ❙ Remaining fuel When the 1st (E) segment of the fuel gauge is flashed (less than 4.0 litres), the estimated amount of remaining fuel can be selected. When the amount of remaining fuel becomes less than 1.0 litre, “ ” will be indicated. The amount of remaining fuel is calculated from the driving conditions. The indicated amount of remaining fuel may be different from the actual amount. When the fuel gauge near to E or when E segment blinks, fill fuel promptly. Operation Guide Available driving distance When the 1st (E) segment of the fuel gauge is flashed (less than 4.0 litres), the estimated available driving distance is indicated. When the amount of remaining fuel becomes less than 1.0 litre, “ ” will be indicated. The indicated available driving distance is by calculation depending on the driving conditions, and the indicated figure may not always be the actual allowable distance. When the fuel gauge near to E or when E segment blinks, fill fuel promptly. 木曜日 29 12 VFR1200X-32MGH600.book 30 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments (Continued) (VFR1200XD) Operation Guide (P23) Speedometer Fuel gauge (P21) TOTAL/TRIP button FCD button TOTAL/TRIP button & FCD button (P20) Tachometer NOTICE Do not operate the engine in the tachometer red zone. Excessive engine speed can adversely affect engine life. Tachometer red zone (excessive engine rpm range) 30 Air temperature gauge (AIR) (P22) Coolant temperature gauge ( ) Fuel mileage meter (P26) When the 1st (E) segment of the fuel gauge is flashed (P27) Odometer [TOTAL] & Tripmeter [TRIP A/B] (P23) Clock (12-hour display) To set the clock (P24) Backlight brightness adjustment (P25) 12 VFR1200X-32MGH600.book 31 ページ ２０１２年７月５日 木曜日 午後１０時５７分 u “-” appears for a few seconds and then goes off when the engine starts. u “-” flashes when the engine stop switch position is changed from RUN to OFF with the ignition switch on. u “-” flashes when the ignition switch is turned on with the engine stop switch OFF Operation Guide D indicator Comes on when the D mode is selected in the AT MODE. (P44) S indicator Comes on when the S mode is selected in the AT MODE. (P44) Gear position indicator The gear position is shown in the gear position indicator when the D, S mode or MT MODE are selected. position position. The indicator may flash if: u The front wheel leaves the ground. u You turn the wheel while the motorcycle is upright on the stand. This is normal. To operate the system again, turn the ignition switch off, then on again. If the “-” indicator is blinking in the gear position window while riding: (P97) continued 31 12 VFR1200X-32MGH600.book 32 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Indicators Operation Guide Parking brake indicator (VFR1200XD only) Lights as a reminder that you have not released the parking brake lever. (P36) Low oil pressure indicator Comes on when the ignition switch is turned on. Goes off when the engine starts. If it comes on while engine is running: (P93) ABS (Anti-lock Brake System) indicator Comes on when the ignition switch is turned on. Goes off when your speed reaches approximately 10 km/h (6 mph). If it comes on while riding: (P94) High coolant temperature indicator If it comes on while riding: (P92) PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) Comes on briefly when the ignition switch is turned on with the engine stop switch in the RUN position. If it comes on while engine is running: (P93) 32 12 VFR1200X-32MGH600.book 33 ページ ２０１２年７月５日 木曜日 午後１０時５７分 TCS (Traction Control System) OFF indicator Comes on when the TCS is turned off. Operation Guide HISS indicator (P113) • Comes on briefly when the ignition switch is turned on. Goes off if the ignition key has the correct coding. • Flashes every 2 seconds for 24 hours when the ignition switch is turned off. High beam indicator Right turn signal indicator Neutral indicator Comes on when the transmission is in Neutral. Left turn signal indicator TCS (Traction Control System) indicator • Comes on when the ignition switch is turned on. Goes off when your speed reaches approximately 10 km/h (6 mph) to indicate TCS is ready to work. • Blinks when TCS is operating. If it comes on while riding: (P95) 33 12 VFR1200X-32MGH600.book 34 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Switches (VFR1200X) Operation Guide 34 Engine stop switch Should normally remain in the RUN position. u In an emergency, switch to the OFF position to stop the engine. Start button Headlight turns off when operating the starter motor. Hazard switch TCS (Traction Control System) OFF switch Switchable when the Press and hold to turn the TCS on and off. ignition switch is on. u The TCS OFF indicator comes on when TCS is turned off. Can be turned to off Turn signal switch regardless of the u Pressing the switch turns the turn signal off. ignition switch Horn button position. Headlight dimmer switch u The signals continue • : High beam flashing with the • : Low beam ignition switch is OFF Passing light control switch or LOCK after the Flashes the high beam headlight. hazard switch is on. 12 VFR1200X-32MGH600.book 35 ページ ２０１２年７月５日 木曜日 午後１０時５７分 ON Ignition Switch Switches the electrical system on/off, locks the steering. OFF Turns engine off. LOCK Locks steering. Steering Lock ❙ Locking Lock the steering when parking to help prevent theft. A U-shaped wheel lock or similar device is also recommended. !a Turn the handlebar all the way to the left. !a !b Turn Push Operation Guide u Key can be removed when in the OFF or LOCK position. Turns electrical system on for starting/riding. !b Push the key down, and turn the ignition switch to the LOCK position. u Jiggle the handlebar if the lock is difficult to engage. !c Remove the key. ❙ Unlocking Ignition key Insert the key, push it in, and turn the ignition switch to the OFF position. 35 12 VFR1200X-32MGH600.book 36 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Switches (Continued) Operation Guide (VFR1200XD) Parking brake lever and Release button Be sure the parking brake is applied while parking and warming up the engine. u Make sure the parking brake lever is released before riding. To apply the parking brake lock Pull the parking brake lever back to lock the rear wheel. u Be sure the release button pops out and parking brake lever is not released. u The parking brake lock will not function if the parking brake is not adjusted properly. (P78) To release the parking brake lock Release the parking brake lever by lightly pulling in the lever (!a) and pressing the release button (!b). u Before riding, check that the parking brake indicator is turned off and make sure that the parking brake is fully released so there is no drag on the rear wheel. 36 Hazard switch (P34) !a Shift up switch (+) To shift up the gear. (P45) Headlight dimmer/ Passing light control switch • : High beam • : Low beam • : Flashes the high beam headlight. Turn signal switch Shift down switch (-) To shift down the gear. !b (P45) 12 VFR1200X-32MGH600.book 37 ページ ２０１２年７月５日 木曜日 午後１０時５７分 u Key can be removed when in the OFF or LOCK position. Steering Lock (P35) AT/MT Switch To shift between the AT MODE and MT MODE. Horn button N-D Switch To shift between Neutral and AT MODE. (P44) Start button Headlight turns off when operating the starter motor. Operation Guide Ignition Switch Switches the electrical system on/off, locks the steering. (P44) Engine stop switch Should normally remain in the RUN position. u In an emergency, switch to the OFF position to stop the engine. TCS (Traction Control System) OFF switch Press and hold to turn the TCS on and off. u The TCS OFF indicator comes on when TCS is turned off. 37 12 VFR1200X-32MGH600.book 38 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Starting the Engine Operation Guide (VFR1200X) Start your engine using the following procedure, regardless of whether the engine is cold or warm. !c !a !a Make sure the engine stop switch is in the RUN position. !b Turn the ignition switch to the ON position. !c Shift the transmission to Neutral ( N indicator comes on). Alternatively, pull in the clutch lever to start your motorcycle with the transmission in gear so long as the side stand is raised. !d Press the start button with the throttle completely closed. !d !b NOTICE • If the engine does not start within 5 seconds, turn the ignition off and wait 10 seconds before trying to start the engine again for recovery of battery voltage. • Extended fast idling and revving the engine can damage the engine, and the exhaust system. • Snapping the throttle or fast idling for more than about 5 minutes may cause exhaust pipe discolouration. 38 If the engine does not start: !a Open the throttle fully and press the start button for 5 seconds. !b Repeat the normal starting procedure. !c If the engine starts, open the throttle slightly if idling is unstable. !d If the engine does not start, wait 10 seconds before trying steps !a & !b again. ❙ If Engine Will Not Start (P91) 12 VFR1200X-32MGH600.book 39 ページ ２０１２年７月５日 !e !c !a 午後１０時５７分 !a Make sure the engine stop switch is in the RUN position. !b Turn the ignition switch to the ON position. !c Check the transmission in Neutral ( N indicator comes on). !d Press the start button with the throttle completely closed. !e Make sure the parking brake lever is released before riding. Operation Guide (VFR1200XD) Start your engine using the following procedure, regardless of whether the engine is cold or warm. 木曜日 ❙ If Engine Does Not Start (P38) !d !b NOTICE • If the engine does not start within 5 seconds, turn the ignition off and wait 10 seconds before trying to start the engine again for recovery of battery voltage. • Extended fast idling and revving the engine can damage the engine, and the exhaust system. • Snapping the throttle or fast idling for more than about 5 minutes may cause exhaust pipe discolouration. When you stop the engine !a To stop the engine, put gear to Neutral ( N indicator comes on). u If you turn the ignition switch to the OFF position when the motorcycle in gear, the engine will shut off with the clutch disengaged. !b Turn the ignition switch off. !c Pull the parking brake lever when you park the motorcycle. 39 12 VFR1200X-32MGH600.book 40 ページ ２０１２年７月５日 Shifting Gears Operation Guide (VFR1200X) Your motorcycle transmission has six forward gears in a one-down, five-up shift pattern. 2 3 4 5 6 N 1 If you put the motorcycle in gear with the side stand down, the engine will shut off. 40 木曜日 午後１０時５７分 12 VFR1200X-32MGH600.book 41 ページ ２０１２年７月５日 午後１０時５７分 Operation Guide (VFR1200XD) VFR1200XD is equipped with an automatically controlled 6-speed transmission. It can be shifted automatically (by AT MODE) or manually (by MT MODE). 木曜日 continued 41 12 VFR1200X-32MGH600.book 42 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Shifting Gears (Continued) (VFR1200XD) Dual Clutch Transmission Operation Guide In order to respond to rider demands in a broad range of situations, the transmission is equipped with three operating modes, AT MODE (including D mode for regular operation and S mode for sporty riding); and MT MODE (MT mode for a 6-speed manual operation), which delivers the same shift feel as a manual transmission. The Dual Clutch Transmission system runs a self check immediately after starting the engine. “-” appears in the gear position indicator window for a few seconds, then goes out. While “-” appears, you cannot shift into gear. 42 N-D switch AT-MT switch AT MT MODE MODE 12 VFR1200X-32MGH600.book 43 ページ ２０１２年７月５日 u Turn the ignition off and on again. u If neutral is still not selected after turning the engine off then on again. (P97) You may hear (click) noises when the transmission shifts to Neutral (N). This is normal. When you can change between N and D: u Motorcycle is stopped and the engine is idling. u Throttle is completely off. It is not possible to change from Neutral to D mode while the throttle is applied. u You cannot change between N and D mode while the wheels are rotating. u Side stand is raised. 午後１０時５７分 NOTICE To prevent clutch damage, do not use the throttle to keep the motorcycle stopped uphill. AT MODE: In this mode the gears are shifted automatically according to your riding conditions. And also using the shift up switch (+) or shift down switch (-), you can temporarily shift up or down. These switches are convenient when you want to temporarily down-shift in front of a curve, etc. (P45) You can choose between two modes within AT MODE: D mode and S mode. D mode (AT): This is the standard mode when AT MODE is selected. Select D mode for regular operation and efficient fuel economy. Operation Guide Neutral (N): Neutral is selected automatically when you turn the ignition switch to ON. If neutral is not selected when you turn the ignition switch to ON: 木曜日 43 12 VFR1200X-32MGH600.book 44 ページ ２０１２年７月５日 Operation Guide S mode (AT): Select this mode while riding in AT MODE when you need more power, such as when overtaking, climbing hills, pulling away. MT MODE: MT MODE (6-speed manual operation) You can choose between 6 gears in this mode. Changing between Neutral and AT/MT Changing from Neutral (N) to AT MODE Press the D/S side of the N-D switch (!a). The D mode indicator comes on, ”1” is shown in the gear position indicator and first gear is selected. Changing from AT or MT MODE to Neutral Press N on the N-D switch (!b). Changing between D mode and S mode while in AT MODE Press the D/S side of the N-D switch. The S or D mode indicator comes on (!c,!d). 44 木曜日 午後１０時５７分 Changing between AT MODE and MT MODE Press the AT/MT switch (!e). The S or D indicator goes out while MT MODE is selected (!f). !e N-D switch AT-MT !a switch !b !c !d !f 12 VFR1200X-32MGH600.book 45 ページ ２０１２年７月５日 u If the MT MODE is selected, the transmission does not shift up automatically. Do not allow the engine revs to go into the red zone. u The transmission automatically shifts down when you slow down, even in MT MODE. u You will start from 1st gear even if MT MODE is selected. Downshifting Blipping Control In MT mode, this system controls down shifting with the throttle completely closed by increasing engine revs automatically to match the gear ratio. u This system may not increase engine revs in some running conditions. 午後１０時５７分 Gear shift operation Shifting Up: Press the shift up switch (+) (!g). Shifting Down: Press the shift down switch (-) (!h). You cannot continue shifting gear by keeping the shift switch pressed. To continue shifting gear release the switch and press it again. Operation Guide Riding in MT MODE Shift up and down with the + and - switch. The selected gear is shown on the gear position indicator. 木曜日 !g !h Shift Limit You can’t shift gear down if the engine revs exceed the limit. 45 12 VFR1200X-32MGH600.book 46 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Refuelling Opening the Fuel Fill Cap Fuel fill cap Ignition key Filler neck plate Operation Guide Fuel level (max) Fuel filler opening Closing the Fuel Fill Cap !a After refuelling, push the fuel fill cap closed until it locks. Lock cover Do not fill with fuel above the plate. Fuel type: Unleaded petrol only Fuel octane number: Your motorcycle is designed to use Research Octane Number (RON) 95 or higher. Tank capacity: 21.5 litres (5.68 US gal, 4.73 Imp gal) ❙ Refuelling and Fuel Guideline (P15) 46 Open the lock cover, insert the ignition key, and turn it clockwise to open the cap. !b Remove the key and close the cover. u The key cannot be removed if the cap is not locked. 3 WARNING Petrol is highly flammable and explosive. You can be burned or seriously injured when handling fuel. • Stop the engine, and keep heat, sparks, and flame away. • Handle fuel only outdoors. • Wipe up spills immediately. 12 VFR1200X-32MGH600.book 47 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Storage Equipment A helmet holder, a helmet set wire (in the tool kit) and a tool kit are located under the seat. There is also space to store a U-shaped lock (Except BR type). The document bag is located on the underside of the seat. U-shaped lock (Except BR type) Helmet holder Helmet set wire u The U-shaped lock is held in place on the rear fender by a rubber strap. u Use the helmet holder only when parked. u Some U-shaped locks may not fit in the compartment due to their size or design. ❙ Removing the seat. (P63) Operation Guide Underside of the seat Tool kit Document bag 3 WARNING Riding with a helmet attached to the holder can interfere with the rear wheel or suspension and could cause a crash in which you can be seriously hurt or killed. Use the helmet holder only while parked. Do not ride with a helmet secured by the holder. 47 12 VFR1200X-32MGH600.book 48 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully before attempting any maintenance. Refer to “Specifications” for service data. Importance of Maintenance ......................P. 49 Maintenance Schedule...............................P. 50 Maintenance Fundamentals ......................P. 53 Tool kit ........................................................P. 62 Removing & Installing Body Components .. P. 63 Seat...........................................................P. 63 Clip ...........................................................P. 64 Final Gear Cover........................................P. 64 Right Engine Heat Guard & Right Under Cowl ..P. 65 Battery ......................................................P. 67 Engine Oil ...................................................P. 68 Coolant ....................................................... P. 74 Brakes/Clutch ............................................. P. 76 Side Stand .................................................. P. 80 Final Drive Oil ............................................ P. 81 Throttle....................................................... P. 82 Other Adjustments .................................... P. 84 Clutch and Brake Levers............................ P. 84 Front Suspension ...................................... P. 85 Rear Suspension........................................ P. 86 Headlight Aim........................................... P. 88 Brakelight Switch ...................................... P. 88 Windscreen Height ................................... P. 89 12 VFR1200X-32MGH600.book 49 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Importance of Maintenance Importance of Maintenance 3 WARNING Improperly maintaining your motorcycle or failing to correct a problem before you ride can cause a crash in which you can be seriously hurt or killed. Always follow the inspection and maintenance recommendations and schedules in this owner’s manual. Always read the maintenance instructions before you begin each task, and make sure that you have the tools, parts, and skills required. We cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Maintenance Keeping your motorcycle well-maintained is absolutely essential to your safety and to protect your investment, obtain maximum performance, avoid breakdowns, and reduce air pollution. Maintenance is the owner’s responsibility. Be sure to inspect your motorcycle before each ride, perform the periodic checks specified in the Maintenance Schedule. 2 P. 50 Maintenance Safety Follow these guidelines when performing maintenance. ● Stop the engine and remove the key. ● Park your motorcycle on a firm, level surface using the side stand or a maintenance stand to provide support. ● Allow the engine, muffler, brakes, and other high-temperature parts to cool before servicing as you can get burned. ● Run the engine only when instructed, and do so in a well-ventilated area. 49 12 VFR1200X-32MGH600.book 50 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Schedule The maintenance schedule specifies the maintenance requirements necessary to ensure safe, dependable performance, and proper emission control. Maintenance 50 Maintenance work should be performed in accordance with Honda’s standards and specifications by properly trained and equipped technicians. Your dealer meets all of these requirements. Keep an accurate record of maintenance to help ensure that your motorcycle is properly maintained. Make sure that whomever performs the maintenance completes this record. All scheduled maintenance is considered a normal owner operating cost and will be charged for by your dealer. Retain all receipts. If you sell the motorcycle, these receipts should be transferred with the motorcycle to the new owner. Honda recommends that your dealer should road test your motorcycle after each periodic maintenance is carried out. 12 VFR1200X-32MGH600.book 51 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Schedule Items Pre-ride Check 2 P. 53 × 1,000 km × 1,000 mi 1 0.6 Fuel Line Frequency *1 12 24 8 16 I I Throttle Operation I I 48 32 I I Annual Regular Refer to Check Replace page – I 46 I I I I 82 I Air Cleaner *2 R R – Spark Plug I R – Valve Clearance I I Engine Oil I Engine Oil Filter Clutch Oil Filter VFR1200XD Engine Idle Speed – R R R R R R 68 R R R R R R 69 R 72 R – I I I I I I I I I I Cooling System I I I I I – Secondary Air Supply System I I I I I – Radiator Coolant *3 I R I Maintenance Level : Intermediate. We recommend service by your dealer, unless you have the necessary tools and are mechanically skilled. Procedures are provided in an official Honda Shop Manual. : Technical. In the interest of safety, have your motorcycle serviced by your dealer. Maintenance Fuel Level 36 24 3 Years 74 Maintenance Legend I : Inspect (clean, adjust, lubricate, or replace if necessary) R : Replace continued 51 12 VFR1200X-32MGH600.book 52 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Schedule Items Pre-ride Check 2 P. 53 × 1,000 km × 1,000 mi 1 0.6 Frequency *1 12 24 8 16 36 24 48 32 Annual Regular Refer to Check Replace page Final Drive Oil Maintenance Brake Fluid *3 I Brake Pads Wear I Brake System I Brakelight Switch Brake Lock Operation VFR1200XD I Headlight Aim Lights/Horn I Engine Stop Switch I Clutch System 81 76 I I I I I I I I I 77 I I I I I 53 I I I I I 88 I I I I I I I I 78 88 I – – VFR1200X I I I I I VFR1200X I I I I I I I I I I 80 I I I I I – I I I I I I – I I I I I I 59 Steering Head Bearings I I I Notes: *1 : At higher odometer readings, repeat at the frequency interval established here. *2 : Service more frequently when riding in unusually wet or dusty areas. *3 : Replacement requires mechanical skill. I I I – Clutch Fluid *3 I Side Stand I Suspension Nuts, Bolts, Fasteners Wheels/Tyres 52 3 Years 2 Years I I 84 2 Years 79 12 VFR1200X-32MGH600.book 53 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals Pre-ride Inspection Check the following items before you ride motorcycle: ● Fuel level − Fill fuel tank when necessary. 2 P. 46 ● Throttle − Check for smooth opening and full closing in all steering positions. 2 P. 82 ● Engine oil level − Add engine oil if necessary. Check for leaks. 2 P. 68 ● Coolant level − Add coolant if required. Check for leaks. 2 P. 74 Maintenance To ensure safety, it is your responsibility to perform a pre-ride inspection and make sure that any problem you find is corrected. A preride inspection is a must, not only for safety, but because having a breakdown, or even a flat tyre, can be a major inconvenience. Brakes − Check operation; Front and Rear: check brake fluid level and pads wear. 2 P. 76, 77 ● Lights and horn − Check that lights, indicators and horn function properly. ● Engine stop switch − Check for proper function. (VFR1200X) ● Clutch − Check clutch fluid level. 2 P. 79 ● Side stand ignition cut-off system − Check for proper function. 2 P. 80 ● Wheels and tyres − Check condition, air pressure and adjust if necessary. 2 P. 59 ● 53 12 VFR1200X-32MGH600.book 54 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals Replacing Parts Always use Honda Genuine Parts or their equivalents to ensure reliability and safety. Except BR, II BR type Maintenance 54 When ordering coloured components, specify the model name, colour, and code mentioned on the colour label. The colour label is attached to the rear fender under the seat. 2 P. 63 Except BR, II BR type Colour label 3 WARNING Installing non-Honda parts may make your motorcycle unsafe and cause a crash in which you can be seriously hurt or killed. Always use Honda Genuine Parts or equivalents that have been designed and approved for your motorcycle. 12 VFR1200X-32MGH600.book 55 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals Battery NOTICE Your battery is a maintenance-free type and can be permanently damaged if the cap strip is removed. This symbol on the battery means that this product must not be treated as household waste. NOTICE An improperly disposed of battery can be harmful to the environment and human health. Always confirm local regulations for battery disposal. 3 WARNING The battery gives off explosive hydrogen gas during normal operation. A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you. Maintenance Your motorcycle has a maintenance-free type battery. You do not have to check the battery electrolyte level or add distilled water. Clean the battery terminals if they become dirty or corroded. Do not remove the battery cap seals. There is no need to remove the cap when charging. Wear protective clothing and a face shield, or have a skilled mechanic do the battery servicing. ❙ Cleaning the Battery Terminals 1. Remove the battery. 2 P. 67 2. If the terminals are starting to corrode and are coated with a white substance, wash with warm water and wipe clean. continued 55 12 VFR1200X-32MGH600.book 56 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals 3. If the terminals are heavily corroded, clean and polish the terminals with a wire brush or sandpaper. Wear safety glasses. Maintenance Fuses protect the electrical circuits on your motorcycle. If something electrical on your motorcycle stops working, check for and replace any blown fuses. 2 P. 109 ❙ Inspecting and Replacing Fuses 4. After cleaning, reinstall the battery. The battery has a limited life span. Consult your dealer about when you should replace the battery. Always replace the battery with another maintenance-free battery of the same type. NOTICE Installing non-Honda electrical accessories can overload the electrical system, discharging the battery and possibly damaging the system. 56 Fuses Turn off the ignition switch to remove and inspect fuses. If a fuse is blown, replace with a fuse of the same rating. For fuse ratings, see “Specifications.” 2 P. 127 Blown fuse NOTICE Replacing a fuse with one that has a higher rating greatly increases the chance of damage to the electrical system. 12 VFR1200X-32MGH600.book 57 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals If a fuse fails repeatedly, you likely have an electrical fault. Have your motorcycle inspected by your dealer. *1. Engine Oil ❙ Selecting the Engine Oil Oil code Oil classification *2. *3. The SAE standard grades oils by their viscosity. The API classification specifies the quality and performance rating of engine oils. Use SG or higher oils, excluding oils marked as “Energy Conserving” on the circular API service symbol. Maintenance Engine oil consumption and oil quality deteriorates according to riding conditions and time elapsed. Check the engine oil level regularly, and add the recommended engine oil if necessary. Dirty oil or old oil should be changed as soon as possible. The JASO T 903 standard is an index for engine oils for 4-stroke motorcycle engines. There are two classes: MA and MB. For example, the following label shows the MA classification. For recommended engine oil, see “Specifications.” 2 P. 126 If you use non-Honda engine oil, check the label to make sure that the oil satisfies all of the following standards: ● JASO T 903 standard*1: MA ● SAE standard*2: 10W-30 ● API classification*3: SG or higher Not recommended Recommended 57 12 VFR1200X-32MGH600.book 58 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals Brake Fluid (Clutch Fluid) Maintenance Do not add or replace brake fluid, except in an emergency. Use only fresh brake fluid from a sealed container. If you do add fluid, have the brake system serviced by your dealer as soon as possible. NOTICE Brake fluid can damage plastic and painted surfaces. Wipe up spills immediately and wash thoroughly. Recommended brake fluid: Honda DOT 4 Brake Fluid or equivalent Final Drive Oil Recommended final drive oil: Hypoid gear oil SAE 80 58 Recommended Coolant Pro Honda HP is a pre-mixed solution of antifreeze and distilled water. Concentration: 50% antifreeze and 50% distilled water A concentration of antifreeze below 40% will not provide proper corrosion and cold temperature protection. A concentration of up to 60% will provide better protection in colder climates. NOTICE Using coolant not specified for aluminium engines or ordinary tap water can cause corrosion. 12 VFR1200X-32MGH600.book 59 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals Tyres (Inspecting/Replacing) ❙ Checking the Air Pressure Inspect the tyres for signs of abnormal wear on the contact surface. Maintenance Visually inspect your tyres and use an air pressure gauge to measure the air pressure at least once a month or any time you think the tyres look low. Always check air pressure when your tyres are cold. ❙ Inspecting for Abnormal Wear ❙ Inspecting for Damage ❙ Inspecting Tread Depth Inspect the tyres for cuts, slits, or cracks that exposes fabric or cords, or nails or other foreign objects embedded in the side of the tyre or the tread. Also inspect for the bumps or bulges in the side walls of the tyres. Inspect the tread wear indicators. If they become visible, replace the tyres immediately. For safe riding, you should replace the tyres when the minimum tread depth is reached. or TWI Wear indicator location mark continued 59 12 VFR1200X-32MGH600.book 60 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals 3 WARNING Maintenance Riding on tyres that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed. Follow all instructions in this owner’s manual regarding tyre inflation and maintenance. Germany German law prohibits use of tyres whose tread depth is less than 1.6 mm. Have your tyres replaced by your dealer. For recommended tyres, air pressure and minimum tread depth, see “Specifications.” 2 P. 126 Follow these guidelines whenever you replace tyres. 60 ● Use the recommended tyres or equivalents of the same size, construction, speed rating, and load range. ● Have the wheel balanced with Honda Genuine balance weights or equivalents after the tyre is installed. ● Do not install a tube inside a tubeless tyre on this motorcycle. Excessive heat build-up can cause the tube to burst. ● Use only tubeless tyres on this motorcycle. The rims are designed for tubeless tyres, and during hard acceleration or braking, a tubetype tyre could slip on the rim and cause the tyre to rapidly deflate. 12 VFR1200X-32MGH600.book 61 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Maintenance Fundamentals 3 WARNING Always use the size and type of tyres recommended in this owner’s manual. This motorcycle is equipped with a viscous type air cleaner element. Air blow cleaning or any other cleaning can degrade the viscous element performance and cause the intake of dust. Do not perform the maintenance. Should be serviced by your dealer. Maintenance Installing improper tyres on your motorcycle can adversely affect handling and stability, and can cause a crash in which you can be seriously hurt or killed. Air Cleaner 61 12 VFR1200X-32MGH600.book 62 ページ ２０１２年７月５日 Tool kit The tool kit is stored under the seat. 2 P. 47 Maintenance 62 You can perform some roadside repairs, minor adjustments and parts replacement with the tools contained in the kit. Spark plug wrench 8 × 12 mm Open end wrench ● 10 × 14 mm Open end wrench ● 12 × 17 mm Open end wrench ● 14 × 17 mm Open end wrench ● Standard/Phillips screwdriver ● Screwdriver grip ● 5 mm Hex wrench ● Helmet set wire ● ● 木曜日 午後１０時５７分 12 VFR1200X-32MGH600.book 63 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Removing & Installing Body Components ❙ Installation Seat Front stay Prongs Seat Rear stays Maintenance Seat lock 1. Insert the front and rear prongs into the front and rear stays on the frame. 2. Push forward and down on the rear of the seat until it locks in place. Make sure that the seat is locked securely in position to pull it up lightly. The seat locks automatically when closed. Take care not to lock your key in the underseat compartment. Ignition key ❙ Removal 1. Insert the ignition key into the seat lock, and turn and hold the key clockwise to unlock the seat. 2. Pull the rear of the seat back and up. 63 12 VFR1200X-32MGH600.book 64 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Removing & Installing Body Components u Clip Clip Final Gear Cover The clips must be removed to remove the right rear cowl. The final gear cover must be opened to drain the final gear oil. Maintenance Bolts ❙ Removal 1. Press down on the centre pin to release the lock. 2. Pull the clip out of the hole. Centre pin ❙ Installation 1. Push the bottom of the centre pin. Final gear cover ❙ Removal 1. Remove the bolts. 2. Open the final gear cover. 2. Insert the clip into the hole. 3. Press down on the centre pin to lock the clip. 64 12 VFR1200X-32MGH600.book 65 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Removing & Installing Body Components u Right Engine Heat Guard & Right Under Cowl ❙ Installation ❙ Removal Install the parts in the reverse order of removal. 1. Remove the clip. 2 P. 64 2. Remove the prongs from the grommets. 3. Remove the right engine heat guard. The right engine heat guard must be opened to service the coolant reserve tank or to check the engine number. (VFR1200X) The right under cowl must be removed to service the engine oil filter. (VFR1200XD) The right under cowl must be removed to service the engine oil filter and the clutch oil filter. Grommets Maintenance Right Engine Heat Guard & Right Under Cowl Prong Right engine heat guard Clip Prong continued 65 12 VFR1200X-32MGH600.book 66 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Removing & Installing Body Components u Right Engine Heat Guard & Right Under Cowl 4. Remove the bolts. 5. Remove the prong from the grommet. 6. Remove the right under cowl. (VFR1200X) (VFR1200XD) Grommet Maintenance Bolt Grommet Prong Bolts Prong Bolts 66 Right under cowl Right under cowl ❙ Installation Install the parts in the reverse order of removal. 12 VFR1200X-32MGH600.book 67 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Removing & Installing Body Components u Battery ❙ Removal Battery Battery Rubber strap Maintenance 1. Remove the seat. 2 P. 63 2. Unhook the rubber strap. 3. Disconnect the negative - terminal from the battery. 4. Disconnect the positive + terminal from the battery. 5. Remove the battery taking care not to drop the terminal nuts. ❙ Installation Negative terminal Positive terminal Install the parts in the reverse order of removal. Always connect the positive + terminal first. Make sure that bolts and nuts are tight. The clock will be reset 1:00 if the battery is disconnected. For proper handling of the battery, see “Maintenance Fundamentals.” 2 P. 55 Battery Goes Dead 2 P. 105 67 12 VFR1200X-32MGH600.book 68 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil Maintenance Checking the Engine Oil Adding Engine Oil 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait 2 to 3 minutes. 3. Place your motorcycle in an upright position on a firm, level surface. 4. Check that the oil level is between the upper and lower level marks in the oil inspection window. If the engine oil is below or near the lower level mark, add the recommended engine oil. 2 P. 57 1. Add the recommended oil until it reaches the upper level mark. u Place your motorcycle in an upright position on a firm, level surface when checking the oil level. u Do not overfill above the upper level mark. u Make sure no foreign objects enter the oil filler opening. u Wipe up any spills immediately. 2. Securely reinstall the oil fill cap. Filler opening Oil level inspection window Upper level Oil fill cap 68 Lower level 12 VFR1200X-32MGH600.book 69 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil u Changing Engine Oil & Filter For the recommended oil and oil selection guidelines, see “Maintenance Fundamentals.” 2 P. 57 1. If the engine is cold, idle the engine for 3 to 5 minutes. 2. Turn the ignition switch off, stop the engine and wait for 2 to 3 minutes. 3. Park on a firm, level surface and lower the side stand. 4. Place a drain pan under the drain bolt. 5. Remove the oil fill cap, drain bolt, and sealing washer to drain the oil. Maintenance NOTICE Overfilling with oil or operating with insufficient oil can cause damage to your engine. Do not mix different brands and grades of oil. They may affect lubrication and clutch operation. Changing Engine Oil & Filter Changing the oil and filter requires special tools. We recommend that you have your motorcycle serviced by your dealer. Use a new Honda Genuine oil filter or equivalent specified for your model. Sealing washer Drain bolt NOTICE Using the wrong oil filter can result in serious damage to the engine. continued 69 12 VFR1200X-32MGH600.book 70 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil u Changing Engine Oil & Filter Maintenance 6. Remove the right engine heat guard and right under cowl. 2 P. 65 7. Remove the oil filter with a filter wrench and let the remaining oil drain out. Make sure the prior seal is not stuck to the engine. u Discard the oil and oil filter at an approved recycling centre. Rubber seal Oil filter 70 8. Apply a thin coat of engine oil to the rubber seal of a new oil filter. 9. Install a new oil filter and tighten. Torque: 26 N·m (2.7 kgf·m, 19 lbf·ft). 10. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. Torque: 29 N·m (3.0 kgf·m, 21 lbf·ft). 12 VFR1200X-32MGH600.book 71 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil u Changing Engine Oil & Filter 11. Fill the crankcase with the recommended oil (2 P. 57) and install the oil fill cap. Maintenance Required oil VFR1200X When changing oil & engine oil filter: 3.3 litres (3.5 US qt, 2.9 Imp qt) When changing oil only: 3.1 litres (3.3 US qt, 2.7 Imp qt) VFR1200XD When changing oil & engine oil filter: 3.9 litres (4.1 US qt, 3.4 Imp qt) When changing oil only: 3.6 litres (3.8 US qt, 3.2 Imp qt) 12. Check the oil level. 2 P. 68 13. Check that there are no oil leaks. 14. Install the right engine heat guard and right under cowl. 71 12 VFR1200X-32MGH600.book 72 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil u Changing Clutch Oil Filter (VFR1200XD only) Changing Clutch Oil Filter (VFR1200XD only) Maintenance Use a new Honda Genuine clutch oil filter or equivalent specified for your model. NOTICE Using the wrong clutch oil filter can result in serious damage to the transmission. 1. Follow the steps 1-7 of Changing Engine Oil & Filter. 2 P. 69 2. Remove the clutch oil filter cover, clutch oil filter and spring by removing the clutch oil filter bolts A and B. u Discard the oil and clutch oil filter at an approved recycling centre. IN-SIDE mark Rubber seal Clutch oil filter Spring Bolt B O-ring Bolts A Clutch oil filter cover 72 12 VFR1200X-32MGH600.book 73 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Oil u Changing Clutch Oil Filter (VFR1200XD only) Torque: 26 N·m (2.7 kgf·m, 19 lbf·ft). 9. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. Torque: 29 N·m (3.0 kgf·m, 21 lbf·ft). 10. Fill the crankcase with the recommended oil (2 P. 57) and install the oil fill cap. Required oil When changing oil, engine oil filter & clutch oil filter: engine oil filter: 4.0 litres (4.2 US qt, 3.5 Imp qt) Maintenance 3. Install the new clutch oil filter with the rubber seal facing in, toward the engine. You will see “IN-SIDE” mark on the clutch oil filter body, near the seal. 4. Replace the O-ring and apply a thin coat of engine oil to the new O-ring when before installing it. 5. Install the spring and the clutch oil filter cover. 6. Install the clutch oil filter bolts A, B and tighten. 7. Apply a thin coat of engine oil to the rubber seal of a new engine oil filter. 2 P. 70 8. Install a new engine oil filter and tighten. 11. Check the oil level. 2 P. 68 12. Check that there are no oil leaks. 13. Install the right engine heat guard and right under cowl. 73 12 VFR1200X-32MGH600.book 74 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Coolant Checking the Coolant Maintenance 1. Place your motorcycle on a firm, level surface. 2. Hold your motorcycle in an upright position. 3. Check that the coolant level is between the UPPER and LOWER level marks in the reserve tank. Reserve tank UPPER level LOWER level Reserve tank cap 74 If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a serious leak. Have your motorcycle inspected by your dealer. Adding Coolant 1. If the coolant level is below the LOWER level, add the recommended coolant 2 P. 58 until the level reaches the UPPER level mark. Add fluid only from the reserve tank cap and do not remove radiator cap. 2. Remove the right engine heat guard. 2 P. 65 12 VFR1200X-32MGH600.book 75 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Coolant u Changing Coolant Changing Coolant Have your dealer change the coolant unless you have the proper tools and are mechanically qualified. Maintenance 3. Remove the reserve tank cap and add fluid while monitoring the coolant level. u Do not overfill above the UPPER level mark. u Make sure no foreign objects enter the reserve tank opening. 4. Securely reinstall the cap. 5. Reinstall the right engine heat guard. 3 WARNING Removing the radiator cap while the engine is hot can cause the coolant to spray out, potentially scalding you. Always let the engine and radiator cool down before removing the radiator cap. 75 12 VFR1200X-32MGH600.book 76 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Brakes/Clutch Checking Brake Fluid Maintenance 1. Place your motorcycle in an upright position on a firm, level surface. 2. Front Check that the brake fluid reservoir is horizontal and that the fluid level is above the LOWER level mark. 3. Rear Check that the brake fluid reservoir is horizontal and that the fluid level is between the LOWER level and UPPER level marks. Front Front brake fluid reservoir LOWER level mark 76 If the brake fluid level in either reservoir is below the LOWER level mark or the brake lever and pedal freeplay becomes excessive, inspect the brake pads for wear. If the brake pads are not worn, you most likely have a leak. Have your motorcycle inspected by your dealer. Rear Rear brake fluid reservoir UPPER level mark LOWER level mark 12 VFR1200X-32MGH600.book 77 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Brakes/Clutch u Inspecting the Brake Pads Inspecting the Brake Pads Front Disc Rear Disc Pad Pad Pad Wear indicator Maintenance Check the condition of the brake pad wear indicator wear indicators. The pads need to be replaced if a brake pad is worn to the wear indicator. 1. Front Inspect the brake pads from below the brake caliper. u Always inspect both left and right calipers. 2. Rear Inspect the brake pads from the rear left of the motorcycle. If necessary have the pads replaced by your dealer. Always replace both left and right brake pads at the same time. Wear indicator 77 12 VFR1200X-32MGH600.book 78 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Brakes/Clutch u Inspecting the Parking Brake (VFR1200XD only) Inspecting the Parking Brake (VFR1200XD only) Maintenance If the efficacy of the parking brake become weak, have the brake adjusted by your dealer. Parking brake lever 78 Place your motorcycle on a firm, level surface. Stop the engine and push your motorcycle while applying the parking brake lever to check the efficacy of the parking brake. 12 VFR1200X-32MGH600.book 79 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Brakes/Clutch u Checking Clutch Fluid (VFR1200X only) Checking Clutch Fluid (VFR1200X only) Maintenance Clutch fluid reservoir If the fluid level is low or if you find fluid leaks, or deterioration or cracks in the hoses and fittings, have the clutch system serviced by your dealer. LOWER level mark 1. Place your motorcycle in an upright position on a firm, level surface. 2. Check that the clutch fluid reservoir cap is horizontal and that the fluid level is above the lower level mark. 79 12 VFR1200X-32MGH600.book 80 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Side Stand Maintenance Side stand spring 1. Check that the side stand operates smoothly. If the side stand is stiff or squeaky, clean the pivot area and lubricate the pivot bolt with clean grease. 2. Check the spring for damage or loss of tension. 3. (VFR1200X) Sit on the motorcycle, put the transmission in Neutral, and raise the side stand. 80 (VFR1200XD) Sit on the motorcycle and raise the side stand. 4. (VFR1200X) Start the engine, pull the clutch lever in, and shift the transmission into gear. (VFR1200XD) Start the engine and press the D/S side of N-D switch to switch the transmission into D mode. 5. Lower the side stand all the way. The engine should stop as you lower the side stand. If the engine doesn’t stop, have your motorcycle inspected by your dealer. 12 VFR1200X-32MGH600.book 81 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Final Drive Oil Changing Final Drive Oil Oil fill hole cap Torque: 12 N·m (1.2 kgf·m, 9 lbf·ft). 6. Fill the final gear with the recommended oil. 2 P. 58 Required oil: 200 cm3 (6.8 US oz, 7.0 Imp oz) Maintenance 1. Place your motorcycle on the side stand on a level surface. 2. Open the final gear cover. 2 P. 64 3. Place a drain pan under the drain bolt. 4. Remove the oil fill hole cap, drain bolt, and sealing washer to drain the oil. 5. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. 7. Check the oil level. It should be flush with the lower edge of the oil fill hole. 8. Reinstall the oil fill hole cap and tighten. Torque: 8 N·m (0.8 kgf·m, 5.9 lbf·ft). Lower edge Drain bolt 9. Check that there are no oil leaks. 10. Close the final gear cover. Sealing washer 81 12 VFR1200X-32MGH600.book 82 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Throttle Checking the Throttle Maintenance 82 With the engine off, check that the throttle rotates smoothly from fully closed to fully open in all steering positions and throttle freeplay is correct. If the throttle does not move smoothly, close automatically, or if the cable is damaged, have the motorcycle inspected by your dealer. Freeplay at the throttle grip flange: 2 to 4 mm (0.08 to 0.16 in). Freeplay Flange 12 VFR1200X-32MGH600.book 83 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Throttle u Adjusting the Throttle Freeplay Adjusting the Throttle Freeplay (VFR1200XD) Cable boot Throttle grip Adjuster – Throttle grip Maintenance 1. Slide the cable boot. 2. Loosen the lock nut. 3. Turn the adjuster until the freeplay is 2 to 4 mm (0.08 to 0.16 in). 4. Tighten the lock nut, return the cable boot, and inspect the throttle action again. (VFR1200X) + Lock nut Adjuster – + Lock nut Cable boot 83 12 VFR1200X-32MGH600.book 84 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments Adjusting the Clutch and Brake Levers Maintenance You can adjust the distances between the tip of the clutch lever and handle grip, and between the tip of the brake lever and handle grip. ❙ Adjustment method Turn the adjuster until the numbers align with the index mark while pushing the lever forward in the desired position. After adjustment, check that the levers operate correctly before riding. NOTICE Do not turn the adjuster beyond its natural limit. VFR1200XD is not equipped with clutch lever and clutch lever adjuster. Clutch lever Index mark Adjuster Forward Forward Handle grip 84 Brake lever 12 VFR1200X-32MGH600.book 85 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments u Adjusting the Front Suspension Adjusting the Front Suspension ❙ Spring Preload You can adjust the rebound damping by the adjuster to suit the load or the road surface. Turn clockwise to increase rebound damping (hard), or turn counterclockwise to decrease rebound damping (soft). The standard position is 7 clicks (VFR1200X)/6 clicks (VFR1200XD) from the maximum setting. Maintenance You can adjust the spring preload by the adjuster to suit the load or the road surface. Turn clockwise to increase spring preload (hard), or turn counterclockwise to decrease spring preload (soft). The standard position is 5th groove (VFR1200X)/4th groove (VFR1200XD) from the top aligning with the top surface of the fork bolts. ❙ Rebound Damping Fork bolt Adjuster (VFR1200X) 5th groove (VFR1200XD) 4th groove Adjuster continued 85 12 VFR1200X-32MGH600.book 86 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments u Adjusting the Rear Suspension NOTICE Do not turn the adjuster beyond its natural limits. Adjust both left and right forks to the same spring preload and rebound damping. Adjusting the Rear Suspension ❙ Spring Preload Maintenance You can adjust the spring preload by the adjuster knob to suit the load or the road surface. Turn clockwise to increase spring preload (hard), or turn counterclockwise to decrease spring preload (soft). The standard position is 7 clicks (VFR1200X)/9 clicks (VFR1200XD) from the minimum setting. Adjuster knob 86 12 VFR1200X-32MGH600.book 87 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments u Adjusting the Rear Suspension ❙ Rebound Damping NOTICE Do not turn the adjuster beyond its natural limits. NOTICE The rear shock absorber damper unit contains high pressure nitrogen gas. Do not attempt to disassemble, service, or improperly dispose of the damper. See your dealer. Maintenance You can adjust the rebound damping by the adjuster to suit the load or the road surface. Turn clockwise to increase rebound damping (hard), or turn counterclockwise to decrease rebound damping (soft). The standard position is 1 3/8 turns (VFR1200X)/7/8 turns (VFR1200XD) from the maximum setting. Adjuster 87 12 VFR1200X-32MGH600.book 88 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments u Adjusting the Headlight Aim Adjusting the Headlight Aim Maintenance You can adjust vertical aim of the headlight for proper alignment. Turn the knob in or out as necessary. Obey local laws and regulations. Adjusting the Brakelight Switch Check the operation of the brakelight switch. Turn the adjusting nut in the direction A if the switch operates too late, or turn the nut in the direction B if the switch operates too soon. Brakelight switch Knob Lower Raise A B Adjusting nut 88 12 VFR1200X-32MGH600.book 89 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Other Adjustments u Adjusting the Windscreen Height Adjusting the Windscreen Height 2. Remove the nuts. Low position High position Washers Maintenance You can adjust the windscreen height 2 positions. 1. Remove the windscreen by removing the screws and the washers. Windscreen Nuts Nuts 3. Set the all nuts to the low position holes or high position holes. 4. Install the windscreen. 5. Install and tighten the screws and washers. Washers Screws Screws 89 12 VFR1200X-32MGH600.book 90 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Troubleshooting Engine Will Not Start (HISS indicator stays on) ......................................................... P. 91 Overheating (High coolant temperature indicator is on)..........................................P. 92 Warning Indicators On or Flashing ...........P. 93 Low Oil Pressure Indicator..........................P. 93 PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) ............P. 93 ABS (Anti-lock Brake System) Indicator ......P. 94 TCS (Traction Control System) Indicator .....P. 95 Other Warning Indications ........................P. 96 If the “-” Indicator is Blinking in the Gear Position Window While Riding............... P. 97 Tyre Puncture............................................. P. 98 Electrical Trouble ..................................... P. 105 Battery Goes Dead .................................. P. 105 Burned-out Light Bulb............................. P. 105 Blown Fuse ............................................. P. 109 12 VFR1200X-32MGH600.book 91 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Engine Will Not Start (HISS indicator stays on) ❙ Starter Motor Operates But Engine Does Not Start ❙ Starter Motor Does Not Operate Check the following items: ● Make sure engine stop switch is RUN position 2 P. 34, 37 ● Check for a blown fuse 2 P. 109 ● Check for a loose battery connection or battery terminal corrosion 2 P. 67 ● Check the condition of the battery 2 P. 105 If the problem continues, have your motorcycle inspected by your dealer. Troubleshooting Check the following items: ● Check the correct engine starting sequence 2 P. 38 ● Check that there is petrol in the fuel tank ● Check if the PGM-FI malfunction indicator lamp (MIL) is on u If the indicator light is on, contact your dealer as soon as possible. ● Check if the HISS indicator stays on u Turn the ignition switch to the OFF position and remove the key. Reinsert the key and turn the ignition switch to the ON position. If the indicator still stays on, check the following: Check if there is no another HISS key (including spare key) close to the ignition switch. Check if there are no any metallic seals or stickers on the key. If the HISS indicator still stays on, have your motorcycle inspected by your dealer. 91 12 VFR1200X-32MGH600.book 92 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Overheating (High coolant temperature indicator is on) Troubleshooting The engine is overheating when the following occurs: ● High coolant temperature indicator comes on ● Acceleration becomes sluggish ● If this occurs, pull safely to the side of the road and perform the following procedure. Extended fast idling may cause the high coolant temperature indicator comes on. NOTICE Continuing to ride with an overheated engine can cause serious damage to the engine. 2. Check that the radiator fan is operating, and then turn the ignition switch to the OFF position. If the fan is not operating: Suspect a fault. Do not start the engine. Transport your motorcycle to your dealer. If the fan is operating: Allow the engine to cool with the ignition switch in the OFF position. 3. After the engine has cooled, inspect the radiator hose and check if there is a leak. 2 P. 74 If there is a leak: 1. Stop the engine using the ignition switch, and then turn the ignition switch to the ON position. 92 Do not start the engine. Transport your motorcycle to your dealer. 4. Check the coolant level in the reserve tank, and add coolant as necessary. 2 P. 74 5. If 1–4 check normal, you may continue riding, but closely monitor the high coolant temperature indicator. 12 VFR1200X-32MGH600.book 93 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Warning Indicators On or Flashing Low Oil Pressure Indicator If the low oil pressure indicator comes on, pull safely to the side of the road and stop the engine. 1. Check the engine oil level, and add oil as necessary. 2 P. 68 2. Start the engine. u Only continue riding if the low oil pressure indicator goes off. Rapid acceleration may momentarily cause the low oil pressure indicator to come on, especially if the oil is at or near the low level. If the low oil pressure indicator stays on when the oil level is at the proper level, stop the engine and contact your dealer. PGM-FI (Programmed Fuel Injection) Malfunction Indicator Lamp (MIL) If the indicator comes on while riding, you may have a serious problem with the PGM-FI system. Reduce speed and have your motorcycle inspected by your dealer as soon as possible. Troubleshooting NOTICE Continuing to ride with low oil pressure can cause serious damage to the engine. If the engine oil level goes down rapidly, your motorcycle may have a leak or another serious problem. Have your motorcycle inspected by your dealer. 93 12 VFR1200X-32MGH600.book 94 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Warning Indicators On or Flashing u ABS (Anti-lock Brake System) Indicator ABS (Anti-lock Brake System) Indicator Troubleshooting 94 If the indicator operates in one of the following ways, you may have a serious problem with the brake system. Reduce your speed and have your motorcycle inspected by your dealer as soon as possible. Indicator comes on or starts flashing while riding. ● Indicator does not come on when the ignition switch is in the ON position. ● Indicator does not go off at speeds above 10 km/h (6 mph). ● If the ABS indicator stays on, your brakes will continue to work as a conventional system, but without the anti-locking function. The ABS indicator may flash if you turn the rear wheel while your motorcycle is lifted off the ground. In this case, turn the ignition switch off and then on again. The ABS indicator will go off after your speed reaches 10 km/h (6 mph). 12 VFR1200X-32MGH600.book 95 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Warning Indicators On or Flashing u TCS (Traction Control System) Indicator TCS (Traction Control System) Indicator Indicator comes on while riding. Indicator does not comes on when the ignition switch is in turned on. ● Indicator does not go off at speeds above 10 km/h (6 mph). ● ● The TCS indicator may comes on if you turn the rear wheel while your motorcycle is lifted off the ground. In this case, turn the ignition switch off and on again. The TCS indicator will go off after your speed reaches 10 km/h (6 mph). Troubleshooting If the indicator operates in one of the following ways, you may have a serious problem with the TCS (Traction Control System). Reduce your speed and have your motorcycle inspected by your dealer as soon as possible. Even when the TCS indicator is on, your motorcycle will have normal riding ability without TCS function. u When the indicator comes on while the TCS is in operation, you will have to close the throttle grip completely to regain normal riding ability. 95 12 VFR1200X-32MGH600.book 96 ページ ２０１２年７月５日 Other Warning Indications Fuel Gauge Failure Indication If the fuel system has an error, all segments will blink as shown in the illustration. If this occurs, see your dealer as soon as possible. Troubleshooting 96 木曜日 午後１０時５７分 12 VFR1200X-32MGH600.book 97 ページ ２０１２年７月５日 木曜日 午後１０時５７分 If the “-” Indicator is Blinking in the Gear Position Window While Riding If you still cannot start the engine: Start the engine while applying the brake lever or pressing the brake pedal. If you can shift from N to D mode: Start the engine while applying the brake lever or pressing the brake pedal. If you can’t shift from N to D mode and the “-” indicator is blinking: Damage is preventing you from riding. Have your motorcycle inspected by your dealer immediately. Troubleshooting (VFR1200XD only) If the “-” indicator is blinking while riding, you may have a serious problem with the Dual Clutch Transmission system. Park your motorcycle in a safe place and have your motorcycle inspected by dealer immediately. There is possibility for you to ride yourself to go to dealer if you try to follow the procedure below. 1. Turn the ignition switch to OFF. 2. Turn the ignition switch to ON and start the engine. If you cannot start the engine: Turn the ignition switch to OFF and move the motorcycle back and forth slightly (to disengage the gears). Turn the ignition switch to ON again and start the engine. 97 12 VFR1200X-32MGH600.book 98 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture Repairing a puncture or removing a wheel requires special tools and technical expertise. We recommend you have this type of service performed by your dealer. After an emergency repair, always have the tyre inspected/replaced by your dealer. Troubleshooting 98 Emergency Repair Using a Tyre Repair Kit If your tyre has a minor puncture, you can make an emergency repair using a tubeless tyre repair kit. Follow the instructions provided with the emergency tyre repair kit. Riding your motorcycle with a temporary tyre repair is very risky. Do not exceed 50 km/h (30 mph). Have the tyre replaced by your dealer as soon as possible. 3 WARNING Riding your motorcycle with a temporary tyre repair can be risky. If the temporary repair fails, you can crash and be seriously injured or killed. If you must ride with a temporary tyre repair, ride slowly and carefully and do not exceed 50 km/h (30 mph) until the tyre is replaced. Removing Wheels Follow these procedures if you need to remove a wheel in order to repair a puncture. 12 VFR1200X-32MGH600.book 99 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels When removing and installing the wheel, be careful not to damage the wheel speed sensor and pulser ring. ❙ Front Wheel 3. On the left side, remove the mounting bolts and remove the brake caliper. Left side Troubleshooting Removal 1. Park on a firm, level surface. 2. Cover both sides of the front wheel and brake caliper with protective tape or cloth. 4. On the right side, remove the mounting bolts and remove the brake caliper. u Support the brake caliper assembly so that it doesn’t hang from the brake hose. Do not twist the brake hose. u Avoid getting grease, oil, or dirt on the disc or pad surfaces. u Do not pull the brake lever or push the brake pedal while the brake caliper is removed. u Take care to prevent the brake caliper from scratching the wheel during removal. Right side Tape or cloth Mounting bolts Brake calipers continued 99 12 VFR1200X-32MGH600.book 100 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels Troubleshooting 5. Remove the front axle bolt. 6. Loosen the right axle pinch bolts. 7. Support your motorcycle securely and raise the front wheel off the ground using a maintenance stand or a hoist. 8. Loosen the left axle pinch bolts. 9. On the left side, withdraw the front axle shaft, and remove the side collars and wheel. Front axle bolt Front axle pinch bolts Front axle shaft 100 12 VFR1200X-32MGH600.book 101 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels Surface of fork leg 4. Tighten the left axle pinch bolts to hold the axle. 5. Tighten the axle bolt. Torque: 59 N·m (6.0 kgf·m, 44 lbf·ft). 6. Loosen the left axle pinch bolts. 7. Tighten the right axle pinch bolts. Torque: 22 N·m (2.2 kgf·m, 16 lbf·ft). 8. Install the right brake caliper and tighten the mounting bolts. Troubleshooting Installation 1. Attach the side collars to the wheel. 2. On the left side, place the wheel between the fork legs and insert the lightly greased front axle shaft to the end, through the left fork leg and wheel hub. 3. Align the end of the front axle shaft with the surface of the fork leg. Torque: 31 N·m (3.2 kgf·m, 23 lbf·ft). End of front axle shaft continued 101 12 VFR1200X-32MGH600.book 102 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels 9. Install the left brake caliper and tighten the mounting bolts. Torque: 31 N·m (3.2 kgf·m, 23 lbf·ft). Troubleshooting u Take care to prevent the brake caliper from scratching the wheel during installation. u Use new mounting bolts when installing the brake caliper. NOTICE When installing the brake caliper into position on the fork leg, carefully fit the brake disc between the pads to avoid scratching them. 10. Lower the front wheel on the ground. 11. Apply the brake lever and brake pedal several times. Then, pump the fork several times. 102 12. Retighten the left axle pinch bolts. Torque: 22 N·m (2.2 kgf·m, 16 lbf·ft). 13. Raise the front wheel off the ground again, and check that the wheel rotates freely after you release the brake. 14. Remove the protective tape or cloth. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. 12 VFR1200X-32MGH600.book 103 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels ❙ Rear Wheel Nut Rear wheel nuts Washers Muffler Troubleshooting Removal 1. Support your motorcycle securely and raise the rear wheel off the ground using a maintenance stand or a hoist. 2. Loosen the muffler band bolt. 3. Remove the muffler stay bolt, nut and washers. 4. Move the muffler outward. 5. Remove the rear wheel nuts, and remove the rear wheel. Rear wheel nuts Muffler band bolt Muffler stay bolt continued 103 12 VFR1200X-32MGH600.book 104 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Tyre Puncture u Removing Wheels Installation 1. To install the rear wheel, reverse the removal procedure. 2. Install the rear wheel and tighten the rear wheel nuts equally. Troubleshooting 104 Torque: 108 N·m (11 kgf·m, 80 lbf·ft). 3. Tighten the muffler band bolt. Torque: 17 N·m (1.7 kgf·m, 13 lbf·ft). 4. Check that the wheel rotates freely. If a torque wrench was not used for installation, see your dealer as soon as possible to verify proper assembly. Improper assembly may lead to loss of braking capacity. 12 VFR1200X-32MGH600.book 105 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble Burned-out Light Bulb Charge the battery using a motorcycle battery charger. Remove the battery from the motorcycle while charging. Do not use an automobile-type battery charger, as these can overheat a motorcycle battery and cause permanent damage. If the battery does not recover after recharging, contact your dealer. Follow the procedure below to replace a burned-out light bulb. Turn the ignition switch to the OFF or LOCK position. Allow the bulb to cool before replacing it. Do not use bulbs other than those specified. Check the replacement bulb for correct operation before riding. NOTICE Jump starting using an automobile battery is not recommended, as this can damage your motorcycle’s electrical system. For the light bulb wattage, see “Specifications.” 2 P. 127 Troubleshooting Battery Goes Dead continued 105 12 VFR1200X-32MGH600.book 106 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Headlight Bulb Pin Bulb Troubleshooting Socket Socket cover 1. Remove the socket cover by turning it counterclockwise. 2. Pull the socket off the bulb without turning it. 106 3. Press the pin down and pull out the bulb without turning it. 4. Install a new bulb and parts in the reverse order of removal. Do not touch the glass surface with your fingers. If you touch the bulb with your bare hands, clean it with a cloth moistened with alcohol. 12 VFR1200X-32MGH600.book 107 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Position Light Bulb ❙ Brake/Tail Light Socket Bulb Brake/Tail light Troubleshooting 1. Pull the socket and remove it. 2. Pull out the bulb without turning. 3. Install a new bulb and parts in the reverse order of removal. The brake and tail light uses several LEDs. If there is a LED which is not turned on, see your dealer for this service. continued 107 12 VFR1200X-32MGH600.book 108 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble u Burned-out Light Bulb ❙ Front/Rear Turn Signal Light ❙ License Plate Light License plate light Troubleshooting Turn signal light Front and rear turn signal light uses several LEDs. If there is a LED which is not turned on, see your dealer for this service. 108 License plate light uses several LEDs. If there is a LED which is not turned on, see your dealer for this service. 12 VFR1200X-32MGH600.book 109 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble u Blown Fuse Blown Fuse Before handling fuses, see “Inspecting and Replacing Fuses.” 2 P. 56 ❙ Fuse Box Fuses Spare fuses Fuse box cover Troubleshooting Fuse puller 1. Remove the seat. 2 P. 63 2. Remove the fuse box cover. 3. Pull the main fuse A and other fuses out one by one with the fuse puller in the fuse box cover and check for a blown fuse. Always replace a blown fuse with a spare of the same rating. 4. Reinstall the fuse box cover. 5. Reinstall the seat. Main fuse A continued 109 12 VFR1200X-32MGH600.book 110 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Electrical Trouble u Blown Fuse ❙ Fuse Holder Fuses Starter magnetic switch cover Troubleshooting NOTICE If a fuse fails repeatedly, you likely have an electrical problem. Have your motorcycle inspected by your dealer. Main fuse B Fuse holder FI fuse 1. Remove the seat. 2 P. 63 2. Remove the starter magnetic switch cover. 110 3. Pull the main fuse B and other fuse out one by one with the fuse puller and check for a blown fuse. Always replace a blown fuse with a spare of the same rating. u Spare fuses are provided in the fuse box. u A fuse puller is provided in the fuse box cover. 4. Reinstall parts in the reverse order of removal. 12 VFR1200X-32MGH600.book 111 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Information Keys...........................................................P. 112 Instruments, Controls, & Other Features...P. 113 Fuels Containing Alcohol (Except Brazil) .... P. 116 Catalytic Converter ..................................P. 117 Caring for Your Motorcycle.....................P. 118 Storing Your Motorcycle .........................P. 121 Transporting Your Motorcycle ................P. 122 You & the Environment ...........................P. 123 Serial Numbers .........................................P. 124 12 VFR1200X-32MGH600.book 112 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Keys Keys Ignition key Information The ignition key contains a special coded chip that is recognized by the immobilizer system (HISS) in order to start the engine. Handle the key carefully to prevent damaging the HISS components. ● Do not bend keys or subject them to undue stress. ● Avoid prolonged exposure to sunlight or high temperatures. ● Do not grind, drill or in any way alter their shape. ● Do not expose to strong magnetic objects. If you lose all keys and the key number plate, the PGM-FI unit/ignition control module must be replaced by your dealer. To avoid this, keep a duplicate key. If you lose a key, make another duplicate key immediately. 112 To make a duplicate key and register it with your HISS system, take the spare key, the key number plate, and the motorcycle to your dealer. A metal key holder may cause damage to the area surrounding the ignition switch. 12 VFR1200X-32MGH600.book 113 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments, Controls, & Other Features Instruments, Controls, & Other Features Ignition Switch Engine Stop Switch Do not use the engine stop switch except in an emergency. Doing so when riding will cause the engine to suddenly turn off, making riding unsafe. If you stop the engine using the engine stop switch, turn the ignition switch off. Failing to do so will drain the battery. Odometer The display locks 999,999 when the read-out exceeds 999,999. The tripmeter A, B returns to 0.0 when the read-out exceeds 99,999.9. HISS The Honda Ignition Security System (HISS) immobilizes the engine’s ignition system if an improperly-coded key is used to try and start the engine. When the ignition switch is turned off, the HISS immobilizer system is always alert, even if the HISS indicator is not flashing. If the ignition switch is turned on with the engine stop switch in the RUN position, the HISS indicator turns on and goes off after a few seconds to indicate it is OK to start the engine. 2 HISS Indicator Does Not Turn OFF P. 91 Information The headlight is always on when the ignition switch is on. Leaving the ignition switch on with the engine stopped will drain the battery. Do not turn the key while riding. Tripmeter The HISS indicator starts flashing every 2 seconds for 24 hours after the ignition switch is turned off. To prevent or to restore the HISS indicator flashing: continued 113 12 VFR1200X-32MGH600.book 114 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments, Controls, & Other Features 1. Turn the ignition switch on while pressing and holding the TOTAL/TRIP button (2 P. 20, 30). u The HISS indicator flashes once. 2. Turn the ignition switch off. South Africa only Singapore only Brazil only EC Directive Information This immobilizer system complies with R & TTE (Radio and Telecommunications Terminal Equipment and the mutual recognition of their conformity) Directive. The declaration of conformity to R & TTE Directive is provided to the owner at the time of purchase. The declaration of conformity should be kept at a safe place. When the declaration of conformity is lost or is not provided, contact your dealer. 114 0542-08-3333 (01)07898921465038 This equipment operates on a secondary basis and, consequently, must accept harmful interference, including from stations of the same kind, and may not cause harmful interference to systems operating on a primary basis. 12 VFR1200X-32MGH600.book 115 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Instruments, Controls, & Other Features Document Bag The owner’s manual, registration, and insurance information can be stored in the plastic document bag on the underside of the seat. 2 P. 47 Ignition Cut-off System Information A banking (lean angle) sensor automatically stops the engine and fuel pump if the motorcycle falls over. To reset the sensor, you must turn the ignition switch to OFF and back to the ON position before the engine can be restarted. 115 12 VFR1200X-32MGH600.book 116 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Fuels Containing Alcohol (Except Brazil) Fuels Containing Alcohol (Except Brazil) Information 116 Some conventional fuels blended with alcohol are available in some locales to help reduce emissions to meet clean air standards. If you plan to use blended fuel, check that it is unleaded and meets the minimum octane rating requirement. The following fuel blends can be used in your motorcycle: ● Petrol containing ethanol (ethyl alcohol) 10% by volume. u Petrol containing ethanol may be marketed under the name Gasohol. The use of petrol containing more than 10% ethanol may: ● Damage the painting of the fuel tank. ● Damage the rubber tubes of the fuel line. ● Cause corrosion of the fuel tank. ● Cause poor drivability. NOTICE Use of blended fuels containing higher than approved percentages can damage metal, rubber, plastic parts of your fuel system. If you notice any undesirable operating symptoms or performance problems, try a different brand of petrol. 12 VFR1200X-32MGH600.book 117 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Catalytic Converter Catalytic Converter A defective catalytic converter contributes to air pollution and can impair your engine’s performance. A replacement unit must be an original Honda part or equivalent. Information This motorcycle is equipped with a three-way catalytic converter. The catalytic converter contain precious metals that serve as catalysts in high temperature chemical reactions that convert hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx) in the exhaust gasses into safe compounds. Follow these guidelines to protect your motorcycle’s catalytic converter. ● Always use unleaded petrol. Leaded petrol will damage the catalytic converter. ● Keep the engine in good running condition. ● Have your motorcycle serviced if your engine is misfiring, backfiring, stalling, or otherwise not running properly, stop riding and turn off the engine. 117 12 VFR1200X-32MGH600.book 118 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Caring for Your Motorcycle Caring for Your Motorcycle Information Frequent cleaning and polishing is important to ensure the long life of your Honda. A clean motorcycle makes it easier to spot potential problems. In particular, seawater and salts used to prevent ice on roads promote the formation of corrosion. Always wash your motorcycle thoroughly after riding on coastal or treated roads. Washing Allow the engine, muffler, brakes, and other high-temperature parts to cool before washing. 1. Rinse your motorcycle thoroughly using a garden hose to remove loose dirt. 2. If necessary, use a sponge or a soft towel with mild cleaner to remove road grime. u Clean the windscreen, headlight lens, panels, and other plastic components with extra care to avoid scratching them. Avoid 118 directing water into the air cleaner, muffler, and electrical parts. 3. Thoroughly rinse your motorcycle with plenty of clean water and dry with a soft, clean cloth. 4. After the motorcycle dries, lubricate any moving parts. u Make sure that no lubricant spills onto the brakes or tyres. Brake discs or pads contaminated with oil suffer greatly reduced braking effectiveness and can lead to a crash. 5. Apply a coat of wax to prevent corrosion. u Avoid products that contain harsh detergents or chemical solvents. These can damage the metal, paint, and plastic on your motorcycle. Keep the wax clear of the tyres and brakes. u If your motorcycle has any matte painted parts, do not apply a coat of wax to the matte painted surface. 12 VFR1200X-32MGH600.book 119 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Caring for Your Motorcycle ❙ Washing Precautions should dissipate after a few minutes of running the engine. ● Do not use waxes containing compounds at the matte painted surface: u Using plenty of water, clean the matte painted surface with a soft cloth or sponge. Dry with a soft, clean cloth. u Use neutral detergent to clean matte painted surface. Aluminium Components Aluminium will corrode from contact with dirt, mud, or road salt. Clean aluminium parts regularly and follow these guidelines to avoid scratches: ● Do not use stiff brushes, steel wool, or cleaners containing abrasives. ● Avoid riding over or scraping against curbs. Information Follow these guidelines when washing: ● Do not use high-pressure washers: u High-pressure water cleaners can damage moving parts and electrical parts, rendering them inoperable. ● Do not direct water at the muffler: u Water in the muffler can prevent starting and causes rust in the muffler. ● Dry the brakes: u Water adversely affects braking effectiveness. After washing, apply the brakes intermittently at low speed to help dry them. ● Do not direct water under the seat: u Water in the under seat compartment can damage your documents and other belongings. ● Do not direct water at the air cleaner: u Water in the air cleaner can prevent the engine from starting. ● Do not direct water near the headlight: u Any condensation inside the headlight continued 119 12 VFR1200X-32MGH600.book 120 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Caring for Your Motorcycle Panels and Windscreen Information 120 Follow these guidelines to prevent scratches and blemishes: ● Wash gently using a soft sponge and plenty of water. ● To remove stubborn stains, use diluted detergent and rinse thoroughly with plenty of water. ● Avoid getting petrol, brake fluid, or detergents on the instruments, windscreen, panels, or headlight. Exhaust Pipe and Muffler The exhaust pipe and muffler are stainless steel but may become stained by mud or dust. To remove mud or dust, use a wet sponge and a liquid kitchen abrasive, then rinse well with clean water. Dry with chamois or a soft towel. If necessary, remove heat stains by using a commercially available fine texture compound. Then rinse by the same manner as removing mud or dust. NOTICE Even though the exhaust is made of stainless steel, it can become stained. Remove all marks and blemishes as soon as they are noticed. 12 VFR1200X-32MGH600.book 121 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Storing Your Motorcycle Storing Your Motorcycle Information If you store your motorcycle outdoors, you should consider using a full-body motorcycle cover. If you won’t be riding for an extended period, follow these guidelines: ● Wash your motorcycle and wax all painted surfaces (except matte painted surfaces). Coat chrome pieces with rust-inhibiting oil. ● Place your motorcycle on a maintenance stand and position a block so that both tyres are off the ground. ● After rain, remove the body cover and allow the motorcycle to dry. ● Remove the battery (2 P. 67) to prevent discharge. Charge the battery in a shaded, wellventilated area. u If you leave the battery in place, disconnect the negative - terminal to prevent discharge. After removing your motorcycle from storage, inspect all maintenance items required by the Maintenance Schedule. 121 12 VFR1200X-32MGH600.book 122 ページ ２０１２年７月５日 Transporting Your Motorcycle Transporting Your Motorcycle Information 122 If your motorcycle needs to be transported, it should be carried on a motorcycle trailer or a flatbed truck or trailer that has a loading ramp or lifting platform, and motorcycle tie-down straps. Never try to tow your motorcycle with a wheel or wheels on the ground. NOTICE Towing your motorcycle can cause serious damage to the transmission. 木曜日 午後１０時５７分 12 VFR1200X-32MGH600.book 123 ページ ２０１２年７月５日 木曜日 午後１０時５７分 You & the Environment You & the Environment Owning and riding a motorcycle can be enjoyable, but you must do your part to protect the environment. drain or on the ground. Used oil, petrol, coolant, and cleaning solvents contain poisons that can hurt refuse workers and contaminate drinking water, lakes, rivers, and oceans. Choose Sensible Cleaners Information Use a biodegradable detergent when you wash your motorcycle. Avoid aerosol spray cleaners that contain chlorofluorocarbons (CFCs) which damage the atmosphere’s protective ozone layer. Recycle Wastes Put oil and other toxic wastes in approved containers and take them to a recycling centre. Call your local or state office of public works or environmental services to find a recycling centre in your area, and to get instructions on how to dispose of non-recyclable wastes. Do not place used engine oil in the trash, or pour it down a 123 12 VFR1200X-32MGH600.book 124 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Serial Numbers Serial Numbers Information 124 The frame and engine serial numbers uniquely identify your motorcycle and are required in order to register your motorcycle. They may also be required when ordering replacement parts. The frame number is stamped on the right side of the steering head. The engine number is stamped on the side of the crankcase. To check the engine number, remove the right engine heat guard. 2 P. 65 You should record these numbers and keep them in a safe place. Frame number Engine number 12 VFR1200X-32MGH600.book 125 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Specifications Specifications ■ Main Components Type Overall length Overall width Overall height Wheelbase Minimum ground clearance Caster angle Trail Curb weight SC70 2,285 mm (90.0 in) 915 mm (36.0 in) 1,335 mm (52.6 in) 1,595 mm (62.8 in) 180 mm (7.1 in) Maximum weight 194 kg (428 lb) capacity*1 Maximum luggage weight*2 18.5 kg (41 lb) Rear carrier 10 kg (22 lb) Passenger capacity Rider and 1 passenger Minimum turning radius 2.7 m (8.9 ft) Displacement 1,237 cm3 (75.45 cu-in) Bore × stroke 81.0 × 60.0 mm (3.19 × 2.36 in) *1 Including rider, passenger, all luggage, and accessories *2 Includes the weight of the luggage and added accessories Specifications 28º 00´ 107 mm (4.2 in) VFR1200X 275 kg (606 lb) VFR1200XD 285 kg (628 lb) Compression ratio 12.0:1 Unleaded petrol Fuel Recommended: 95 RON or higher Tank capacity 21.5 litres (5.68 US gal, 4.73 Imp gal) YTZ14S Battery 12V-11.2Ah (10 HR) / 11.8Ah (20HR) VFR1200X 1st 2.600 2nd 1.600 3rd 1.260 4th 1.076 5th 0.961 6th 0.897 Gear ratios VFR1200XD 1st 2.250 2nd 1.700 3rd 1.304 4th 1.107 5th 0.967 6th 0.886 VFR1200X 1.738 / 1.060 / 2.545 Reduction ratios (primary / secondary / final) VFR1200XD 1.738 / 1.063 / 2.545 125 12 VFR1200X-32MGH600.book 126 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Specifications ■ Service Data 110/80R19M/C 59V 150/70R17M/C 69V Tyre type Radial, tubeless PIRELLI SCORPION TRAIL E Front BRIDGESTONE BW-501 RADIAL F Recommended Tyres PIRELLI SCORPION TRAIL E Rear BRIDGESTONE BW-502 RADIAL F Front 250 kPa (2.50 kgf/cm2, 36 psi) Tyre air pressure Rear 290 kPa (2.90 kgf/cm2, 42 psi) Front 1.5 mm (0.06 in) Minimum tread depth Rear 2.0 mm (0.08 in) IMR8E-9HES (NGK) or Spark plugs (standard) VUH24ES (DENSO) (non0.80 to 0.90 mm (0.031 to Spark plug gap adjustable) 0.035 in) Idle speed 1,150 ± 100 rpm Honda 4-stroke motorcycle oil API Service Recommended Classification SG or higher, excluding oils marked as “Energy Conserving,” engine oil SAE 10W-30, JASO T 903 standard MA Tyre size Specifications 126 VFR1200X Front Rear Engine oil capacity After draining 3.1 litres (3.3 US qt, 2.7 Imp qt) After draining & engine oil filter change 3.3 litres (3.5 US qt, 2.9 Imp qt) After disassembly 4.0 litres (4.2 US qt, 3.5 Imp qt) VFR1200XD After draining After draining & engine oil filter change After draining, engine & clutch oil filter change After disassembly 3.6 litres (3.8 US qt, 3.2 Imp qt) 3.9 litres (4.1 US qt, 3.4 Imp qt) 4.0 litres (4.2 US qt, 3.5 Imp qt) 4.9 litres (5.2 US qt, 4.3 Imp qt) Recommended Hypoid gear oil SAE 80 final drive oil 200 cm3 (6.8 US oz, After draining 7.0 Imp oz) Final drive oil capacity 220 cm3 (7.4 US oz, After disassembly 7.7 Imp oz) 12 VFR1200X-32MGH600.book 127 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Specifications Recommended brake (clutch) fluid Honda DOT 4 Brake Fluid Cooling system capacity VFR1200X 3.56 litres (3.76 US qt, 3.13 Imp qt) VFR1200XD 3.70 litres (3.91 US qt, 3.26 Imp qt) Recommended coolant Pro Honda HP Coolant ■ Bulbs 12V-55W × 2 LED LED LED 12V-5W × 2 LED Engine oil drain bolt Oil filter Final drive oil fill hole cap Final drive oil drain bolt Front wheel axle bolt Front wheel brake caliper mounting bolts Front wheel axle pinch bolts Rear wheel nuts Muffler band bolt 29 N·m (3.0 kgf·m, 21 lbf·ft) 26 N·m (2.7 kgf·m, 19 lbf·ft) 8 N·m (0.8 kgf·m, 5.9 lbf·ft) 12 N·m (1.2 kgf·m, 9 lbf·ft) 59 N·m (6.0 kgf·m, 44 lbf·ft) 31 N·m (3.2 kgf·m, 23 lbf·ft) 22 N·m (2.2 kgf·m, 16 lbf·ft) 108 N·m (11 kgf·m, 80 lbf·ft) 17 N·m (1.7 kgf·m, 13 lbf·ft) Specifications Headlight Brake/Tail light Front turn signal lights Rear turn signal lights Position light License plate light ■ Torque Specifications ■ Fuses Main fuse Other fuses A 50A B 30A 30A, 20A, 15A, 10A 127 12 VFR1200X-32MGH600.book 128 ページ ２０１２年７月５日 木曜日 午後１０時５７分 Index Index A ABS (Anti-lock Brake System) Indicator............................................. 32, 94 Accessories ................................................. 16 AT Mode .................................. 31, 42, 43, 44 AT/MT Switch............................................. 37 Index 128 B Battery ................................................. 55, 67 Brakelight Switch ...................................... 88 Brakes Fluid ................................................... 58, 76 Pad Wear ................................................. 77 Parking Brake ........................................... 78 Braking....................................................... 12 Bulb Brake/Tail Light....................................... 107 Front Turn Signal .................................... 108 Headlight ............................................... 106 License Plate........................................... 108 Position Light.......................................... 107 Rear Turn Signal ..................................... 108 C Caring for Your Motorcycle ....................118 Clutch Fluid ...................................................58, 79 Colour label................................................54 Combined ABS ...........................................13 Coolant.................................................58, 74 D D mode.....................................31, 42, 43, 44 Digital Clock Adjustment ..........................24 E Electrical Trouble .....................................105 Engine Number ..................................................124 Oil ......................................................57, 68 Oil Filter ..............................................69, 72 Overheats .................................................92 Starting.....................................................38 Stop Switch ....................34, 37, 38, 39, 113 Stopping.................................................113 Environment ............................................123 12 VFR1200X-32MGH600.book 129 ページ ２０１２年７月５日 Equipment Owner’s Manual .................................... 115 Tool Kit .................................................... 62 G Gasohol.................................................... 116 Gear position indicator............................. 31 H Hazard Switch ..................................... 34, 36 Headlight Aim........................................... 88 Headlight Dimmer Switch .................. 34, 36 Helmet Holder........................................... 47 午後１０時５７分 High Beam Indicator ................................. 33 High Coolant Temperature Indicator ............................................. 32, 92 HISS Indicator ...................................... 33, 91 Horn Button......................................... 34, 37 I Ignition Cut-off System Banking Sensor....................................... 115 Side Stand ................................................ 80 Ignition key.............................................. 112 Ignition Switch ........................ 35, 37, 38, 39 Image Labels................................................ 6 Indicators ................................................... 32 Instruments................................................ 20 Index F Final Drive Oil............................................ 81 Flooded Engine ......................................... 38 Frame Number ........................................ 124 Fuel Gauge...................................................... 21 Remaining................................................ 21 Fuels Containing Alcohol ....................... 116 Fuses .................................................. 56, 109 木曜日 L Labels ........................................................... 6 Load Limits................................................. 17 Loading Guidelines ................................... 17 Low Oil Pressure Indicator .................. 32, 93 129 12 VFR1200X-32MGH600.book 130 ページ ２０１２年７月５日 M Maintenance Fundamentals........................................... 53 Importance............................................... 49 Safety....................................................... 49 Schedule .................................................. 50 Maximum Weight Limit ............................ 17 Modifications............................................. 16 N Neutral Indicator ....................................... 33 Index O Odometer ................................................ 113 Oil Engine................................................ 57, 68 Overheating............................................... 92 P Parking....................................................... 14 Parking brake Indicator ............................ 32 Parts Location ............................................ 18 Passing light control switch ................ 34, 36 130 木曜日 午後１０時５７分 Petrol ..................................................46, 116 PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL).....32, 93 Protective Apparel.....................................11 R Recommended Coolant ....................................................58 Final Drive Oil............................................58 Fuel ..........................................................46 Oil ............................................................57 Refuelling...................................................46 Removal Clip...........................................................64 Final Gear Cover .......................................64 Right Engine Heat Guard ..........................65 Right Under Cowl .....................................65 Repair Kit ...................................................98 Riding Precautions.....................................12 S S mode............................................31, 42, 44 Safety Precautions .....................................11 12 VFR1200X-32MGH600.book 131 ページ ２０１２年７月５日 T Tachometer ......................................... 20, 30 TCS (Traction Control System).................. 15 TCS (Traction Control System) Indicator ............................................ 33, 95 TCS (Traction Control System) OFF Indicator .................................................. 33 午後１０時５７分 TCS (Traction Control System) OFF Switch................................................. 34, 37 Throttle ...................................................... 82 Tool kit....................................................... 62 Transporting Your Motorcycle ............... 122 Tripmeter ................................................. 113 Troubleshooting........................................ 90 Turn signal indicators................................ 33 Tyres Air Pressure .............................................. 59 Puncture................................................... 98 Replacing ........................................... 59, 98 W Warning Indicators On.............................. 93 Washing Your Motorcycle ...................... 118 Weight Limit.............................................. 17 Wheels Front removal ........................................... 99 Rear removal .......................................... 103 Windscreen ................................................ 89 Index Serial Numbers ........................................ 124 Shifting Gears............................................ 40 Side Stand.................................................. 80 Side Stand Ignition Cut-off System.......... 80 Specifications .......................................... 125 Speedometer............................................. 21 Start Button............................. 34, 37, 38, 39 Starting the Engine................................... 38 Steering Lock............................................. 35 Stopping Engine ..................................... 113 Storage Equipment ............................................... 47 Owner’s Manual .................................... 115 Storing Your Motorcycle ........................ 121 Switches..................................................... 34 木曜日 131